0
Product Information Packet
Product Information PacketProduct Information Packet
Product Information Packet
Product Name:
Product Name: Product Name:
Product Name: Portable
PortablePortable
Portable
Goal Post
Goal PostGoal Post
Goal Post
Product Part Numbers: 410
Product Part Numbers: 410Product Part Numbers: 410
Product Part Numbers: 410353, 410358
353, 410358353, 410358
353, 410358
1
Table of Contents
Table of ContentsTable of Contents
Table of Contents
Introduction……………………………………………………………………………….……..……………….…
General Safety Rules…………………………………………………………………….…..……………….…..
Symbols……………………………………………………………………………………..…………………...…
Technical Specifications………………………………………………………………………………………….
User Instructions…………………………………………………………………………………………………..
Maintenance…………………………………………………………………………..……………………….…..
Customer Service Information………………………………………………………..……..…..……...……….
Introduction
IntroductionIntroduction
Introduction
The Rogers Athletic Portable Goal Post has been designed and manufactured with safety, performance and
dependability as top priorities, making it easy to operate and maintain.
The care you give your Goal Post will greatly determine your satisfaction with its performance and service life.
We urge careful study of this manual to provide you with a thorough understanding of your new Goal Post
before operating, as well as suggestions for operation and maintenance.
If your manual becomes lost or destroyed, Rogers Athletic will gladly provide you with a new copy. Should you
require additional information or assistance, please feel free to contact us.
BECAUSE ROGERS ATHLETIC MAINTAINS AN ONGOING PROGRAM OF
PRODUCT DEVELOPMENT AND IMPROVEMENT, WE RESERVE THE RIGHT
TO MAKE IMPROVEMENTS IN DESIGN OR CHANGES IN SPECIFICATIONS
WITHOUT INCURRING ANY OBLIGATIONS TO INSTALL THEM ON UNITS
PREVIOUSLY SOLD.
1
2
3
4
5
9
9
2
General Safety Rules
General Safety RulesGeneral Safety Rules
General Safety Rules
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in serious personal
injury.
SAVE THESE INSTRUCTIONS
Use field equipment in a supervised environment with proper gear.
Inspect equipment prior to use. DO NOT use if it appears damaged or inoperable. Inspect belt
for wear or fraying. Replacement belt can be obtained from Rogers Athletic. NOTE: to avoid damage
to equipment, lock the Goal Post down in storage position if winds over 40mph are expected.
Always wear a helmet when training with the Goal Post.
If used during scrimmage or game conditions, attach safety padding (410357).
Save these instructions. Refer to them frequently and use them to instruct others who may use the
Goal Post. If you loan someone your Goal Post, loan them these instructions also.
Read the Product Information Packet. Failure to read this packet is considered a misuse of this
equipment.
Become familiar with all caution and warning decals affixed to the field equipment before use.
Never cover or deface caution/warning labels.
Never move Goal Post while uprights are in up position. Moving the unit only when uprights are
stored reduces risk of tip over.
3
Symbols
SymbolsSymbols
Symbols
Read the Operator’s Manual:
To reduce risk of injury,
user must read and understand operator’s manual before
using this product.
40mph wind warning
:
In the event of winds 40mph or
greater, lock Goal Post down in the storage position.
Safety Alert: Precautions that involve your safety.
Do not move with uprights set up
:
Avoid risk of Goal
Post tipping over by moving it only when the uprights are
stored.
Do Not Climb
:
To reduce risk of injury, do not climb on
field equipment.
For Off
-
Road Use Only Warning Label:
Field equipment
is not intended or designated for roadway travel.
4
Rogers Athletic
Rogers Athletic Rogers Athletic
Rogers Athletic Field Equipment
Field EquipmentField Equipment
Field Equipment Specifications
Specifications Specifications
Specifications
Portable Goal Post
Portable Goal PostPortable Goal Post
Portable Goal Post
Portable Goal Post Construction, Finish, and Hardware
- Constructed of ASTM steel.
- Baked-on powder coat finish.
- Zinc-plated hardware.
H
W
D
Weight: 23’4” = 1200 lbs
18’6” = 1170 lbs
Height: 30’
Width: High-School crossbar 23’4”
College/Pro crossbar 18’6”
Depth: 24’6”
- Use at any practice location and at games
with padding.
- All steel construction.
- Crossbar and uprights powder coated white.
- Includes heavy-duty winch for raising and
lowering the crossbar.
5
1
Take crossbar from storage position and insert in post (do not bolt in place).
Position in approximate location of use and disconnect from vehicle. If locating at a goal line, measure 49”
from the leading edge of the goal line to the front of the Goal Post trolley frame. Lower trailer jack.
49” to leading edge
of rear goal line
2
6
Tilt one side of crossbar to ground and slide upright on crossbar and bolt tight. Repeat for opposite upright.
Level crossbar and secure with bolts. Check that cross bar is parallel to field’s end line before raising.
Bolt a streamer to each upright.
3
4
Level and bolt after uprights
are attached.
7
Crank the jacks until the wheels are 4 to 6 inches off the ground.
Note:
With 2 people, crank both jacks
simultaneously. With only 1 person, crank each jack a couple turns at a time and alternate between jacks.
Pull the pin out of the stabilizer-arm sleeve and slide the arm out. Re-pin through the sleeve at the next hole
in the arm. Pull the jack-assembly pin and rotate the jack perpendicular to the ground (the pin clicks back
into place). Repeat this process for the other stabilizer.
5
6
8
Secure the support beam by pinning through both vertical tubes on the frame. Insert the fastener pin
through the support beam pin. WARNING: Failure to pin the support beam as shown here could result in
severe bodily injury, death and/or property damage. Replace all pins when goal post is not being used.
Raise the Goal Post into full upright
position by cranking the winch at the hitch
end of the trailer.
5
6
9
Maintenance
MaintenanceMaintenance
Maintenance
WARNING!
READ AND UNDERSTAND ALL MAINTENANCE PROCEDURES.
Failure to follow all procedures listed below may cause serious injury and/or
decrease equipment functionality.
Frequently check to see that all bolts are securely fastened.
Finishing recommendations for crossbar and uprights: Prep with mineral spirits or lacquer thinner.
Following the manufacturer’s instructions, prime with True-Test #1280, then apply True-Test XO-Rust
oil base paint in your choice of color.
Field equipment should be washed periodically with soapy water to maintain original surface
finish.
Replace any damaged equipment with genuine Rogers Athletic parts. Failure to do so may result
in unsafe equipment and/or personal injury.
Customer Service
Customer ServiceCustomer Service
Customer Service
For parts or service contact Rogers Athletic Company. When ordering parts be sure to provide all relevant
information available including the name and part number of the equipment purchased. This information is
located on the cover of this product information package. Customer service are Monday through Friday from
8:00 a.m. to 5:00 p.m. Eastern Standard Time. Customers can phone (989) 386-2950 or toll free at (800) 248-
0270. Fax toll free at (888) 549-9659 or mail to:
Rogers Athletic Company
3760 W. Ludington Drive
Farwell, MI 48622
10
Rogers Athletic Company
3760 N. Ludington Drive
Farwell, MI 48622
www.rogersathletic.com
(989) 386-2950
(800) 248-0270
Fax toll free (888) 549-9659
PIP410353
/
