Narrow Door Coolers
Two, Three and
Four Door Remote*
• Remote unit
• All 300 series stainless steel interior construction with
radius corners for easy cleaning
• Foamed-in-place CFC free insulation
• Galvanized steel sub-top
• Black vinyl-clad steel exterior front and sides
• Stainless steel evaporator housing with separate removable
evaporator drain pan
• Stainless steel die cast handle
• Leg sockets recessed into base
• 1/2" thick ABS plastic threshold scuff plate
• 180º swinging doors
Printed in USA Rev. 10-19-07
Specications subject to change without notice. For current specications please visit our website.
Glastender, Inc. • 5400 N Michigan Rd • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Approval/Notes:
Project:
Item #: Qty:
Model #:
4.06
AIA#
SIS#
Electrical
• 120V, 1 phase, 60 Hz
• Dedicated 15 amp circuit is required
• 14 gauge wire connection is made inside the cooler next to
evaporator housing - interior access is through on of the 3/4
"
side knock-out holes (electrician’s choice)
Refrigeration
• R134a or R404a expansion valve & temperature control
included. Specify type required when ordering.
• Recommended condensing unit:
ND40 - 1/4 HP which has an approximate rating of 2,200
BTU/H at +20ºF evaporator temperature
ND60 and ND80 - 1/3 HP which has an approximate rating of
3,064 BTU/H at +20ºF evaporator temperature
• All refrigeration hookups are made at the installation site
Plumbing
• A ten foot length of 1/2" ID by 5/8" OD plastic tubing is pro-
vided to drain condensate. The tubing should exit through one
of the 3/4" side knock-out holes (installer’s choice). The
maximum drainage is one ounce per hour - consult local codes
forcompliance-aoordrainmayberequired
Shelving
• Two adjustable vinyl coated shelves and one bottom
vinyl coated rack per door included
Legs
• 1-5/8" diameter
• Stainless steel bullet feet
Materials
• 22 gauge stainless steel parts include: interior floor, walls, ceiling,
and evaporator housing
• 22 gauge stainless steel type 430 parts include:
front of cabinet
• 22 gauge black vinyl-clad parts include: sides, standard
doors, and compressor compartment housing
• 22 gauge galvanized steel parts include: exterior
sub-top and back
• 16 gauge stainless steel parts include: legs
• 16 gauge galvanized steel parts include: base and
compressor compartment base plate
• 16 gauge zinc plated CR steel parts include: leg
sockets
• 12 gauge stainless steel parts include: hinges,
hinge brackets, and lock brackets
Standard Features
Specications
NSF standard 7 listed for open food storage
† Specify hinge location for each door
ND60-R1-SS(RRR)
COMPONENT
ND__ -_ _-_ _ (____)
Refrigeration
Hook-Up Location:
L = Left or R = Right
Door Hinge Location†:
(from left to right)
L = Left or R = Right
Base Height:
1 = 1"
6 = 6" Legs
Top Style:
N = No finished top
L = Laminated
S = Stainless
Door Style:
B = Black vinyl-clad
U = Unlaminated
L = Laminated
S = Stainless
G = Glass
X = Stainless Glass
Y = Laminated Glass
Size:
40 = 40" Two Door
60 = 60" Three Door
80 = 80" Four Door
* NOTE: These units are manufactured to order. Consult the factory for pricing information
Dimensional Information
ND40
Remote Narrow Door Coolers
ND60
5400 N Michigan Rd • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Printed in USA
ND80
Side View All Models
Plan View
Front Elevation
Plan View
Front Elevation
Front Elevation
Plan View
Model Capacity:
12 oz. bottle /
1/2 barrels
Refrigeration Voltage
Required
ND40 10.8 cases /
2 half barrels
1/4 H.P.
Recommended
R22 Expansion
valve provided
120v /
60 Hz /
1 phase
ND60 17 cases /
3 half barrels
1/3 H.P.
Recommended
R22 Expansion
valve provided
120v /
60 Hz /
1 phase
ND80 22.8 cases /
4 half barrels
1/3 H.P.
Recommended
R22 Expansion
valve provided
120v /
60 Hz /
1 phase
35"
28 5/8"
12"
1 1/2"
37"
40"
EVAPORATOR
HOUSING
ADD 1" TO HEIGHT FOR
FACTORY INSTALLED TOP
29 3/4"
17"
DOOR
OPENING
7 1/2"
7 1/2"
35"
28 5/8"
12"
1 1/2"
57"
60"
EVAPORATOR
HOUSING
ADD 1" TO HEIGHT FOR
FACTORY INSTALLED TOP
DOOR
OPENING
17"
29 3/4"
7 1/2"
35"
39 5/8"
12"
1 1/2"
77"
80"
EVAPORATOR
HOUSING
ADD 1" TO HEIGHT FOR
FACTORY INSTALLED TOP
DOOR
OPENING
17"
29 3/4"
35"
35"
24"
21"
30 3/4"
25 3/4"
EVAPORATOR
HOUSING
ADD 1" TO HEIGHT FOR
FACTORY INSTALLED TOP
ADD 1" TO HEIGHT FOR
FACTORY INSTALLED TOP
48"
6"
4 1/2" 4 1/2"
2 3/8"
22 1/2"
25 1/4"
22 3/4"
25 1/4"
STANDARD CABINET
WITH OPTIONAL 6" LEGS
180°
SWING
/