V-ZUG 64003 Installation guide

Brand: V-ZUG

Model: 64003

Type: Installation guide

V-ZUG 64003, an island hood with extraction and recirculation modes, effortlessly manages kitchen fumes and odors. Designed for hobs with ignition fuses, it maintains a safe cooking environment. Its efficient motor operates at altitudes up to 2000m and seamlessly integrates into your kitchen's electrical system.

Installation instructions

Island hood

Operating mode: Extraction/recirculation

Range hood DSDSR12

J64003113-R06

31/01/2020

J64003113-R06

The appliance should be installed by qualified personnel only.

Each step must be carried out and checked in full in the order specified.

Validity

These installation instructions apply to:

64003 (DSDSR12, construction width 120 cm)

64008 (DSDSR12, construction width 120 cm)

General notes

If other firing systems are being used at the same time (e.g. wood, gas, oil or coal fired heating appliances), safe op-

eration is only possible providing a room negative pressure of 4 Pa (0.04 mbar) is not exceeded at the location of the

appliance.

Risk of toxic fumes! An adequate flow of fresh air must be guaranteed e.g. via non-closable openings in doors or

windows and in combination with an air-intake/exhaust-air wall box or by other technical means.

If the appliance is installed over hobs, each cooking zone must be fitted with an ignition fuse and the minimum dis-

tances (see section «Dimensions») must be adhered to.

Efficient repairs can only be guaranteed if it is possible to uninstall the complete appliance at any time without caus-

ing any damage.

Identification plate

▸ Remove the grease filters. The identification plate is located on the inside of the appliance.

Installation accessories supplied

All fixing elements are contained in the scope of delivery.

Extraction mode

The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burning gas or

other fuels.

Observe the local fire regulations.

Electrical connections

Electrical connections must be carried out by qualified personnel in accordance with the guidelines and standards

for low-voltage installations and the specifications of the local electricity supply companies.

A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An

all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and

socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching

are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and

fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Check old installa-

tions.

▸ The appliance is designed for use up to a max. altitude of 2000 m above sea level.

▸ Refer to the identification plate for information on the required mains voltage, current type and fuse protection.

The mains plug must not be cut off.

Installation instructions

Island hood

Operating mode: Extraction/recirculation

Range hood DSDSR12

J64003113-R06

31/01/2020

J64003113-R06

Dimensions

ø150

1200

670

137

318

700

210

1170

Cut-out measurements

1178±2

675±2

Distance above hob

Minimum distance X above hob: min. 800 mm

Maximum recommended distance: 1300 mm

Installation

Installation with built-in motor

1. Use the screws S1 to secure the lateral supports A far enough

up that they do not yet lock into place.

2. Create a ceiling cover cut-out that is aligned with the centre of

the hob.

3. Reinforce the two long sides of the ceiling cover with square

timber B. The total combined height of the wood and the ceiling

cover must measure between 60mm and 75mm.

The motor housing D can be rotated on all four sides.

4. Position the ceiling hood as close as possible to the ceiling.

Connect the mains connection and the exhaust air pipe.

60–75

5. Push the ceiling hood into the cut-out until the lateral supports

A lock into place.

6. Screw the four screws S1 into the hood until the ceiling hood

comes into contact with the ceiling.

7. Carry out function test.

Installation instructions

Island hood

Operating mode: Extraction/recirculation

Range hood DSDSR12

J64003113-R06

31/01/2020

J64003113-R06

Installation with external motor

Accessories set H43403 is required (not in scope of delivery).

1. Screw lateral supports A upwards as far as possible before

they fold back in using screws S1.

2. Make the ceiling cut-out, aligned with the middle of the hob.

3. Reinforce the ceiling along the two long sides with rectangular

wooden blocks B. Total height including wood and ceiling must

be between 60mm and 75mm.

4. Take off the motor housing D.

64003

64008

5. Unplug motor cable C leading to the motor directly at the motor.

6. Screw locking plate E to the hood and then pull long cable F

through the cut-out in the hood (where necessary, detach the

perforated plate) and plug into existing motor cable C*. If the air

outlet is directed upwards, the round perforation in locking plate

E must be detached. (*) depending on model.

7. Connect exhaust duct 5 to connecting piece G. The connecting

lead can be installed on all four sides.

8. If the air outlet is at the side, detach relevant lateral perforation

J in the hood.

9. Connect mains plug to mains socket.

10. Slide the ceiling hood into the cut-out until the lateral supports

A engage.

11. Screw the four screws S1 into the hood until the ceiling hood

rests on the ceiling.

12. Remove the grease filters. Fasten connecting piece G from the

inside with four screws S2.

Installation instructions

Island hood

Operating mode: Extraction/recirculation

Range hood DSDSR12

J64003113-R06

31/01/2020

J64003113-R06

13. Pass the long cable through air intake housing half H and plug

into the motor.

14. Screw air intake housing half H to motor housing D. Make sure

they are correctly aligned.

15. Connect the ceiling range hood to external motor unit 8 by

means of flat channel 5, transition piece 6 (from angular to

round) and round pipe 7 .

Connection variants for ceiling range hoods

11 Optional recirculation box

16. Connect exhaust air side 9 of external motor unit 8 to exhaust

air pipe 10.

17. Carry out function test.

V-ZUG 64003 Installation guide

V-ZUG 64003 Installation guide

V-ZUG 64003 Installation guide

Related papers

Other documents