Esta 60.000 Owner's manual

Brand: Esta

Model: 60.000

Type: Owner's manual

This manual is also suitable for

Installation instructions

DDE 1500

Order No.: 60.000

DDE 1500 Alu-Mix

Order No.: 60.000.001

Do not use this product unless you have

read the operating instructions and understood them.

Translation of Original operating instructions

60000-08-03

General instructions

DDE 1500

60000-52-03

Edition notice

Translation of Original operating instructions

Document no.: 60000-08-03

Publishing date: 14.09.2017

Model: DDE 1500 // DDE 1500 Alu-Mix

Article no.: 60,000 // 60,000,001

Publisher

ESTA Apparatebau GmbH & Co. KG Tel.: +49 (0) 73 07 80 4 -0

Gotenstr. 2-6 Fax: +49 (0) 73 07 80 4 -500

89250 Senden Email: [email protected]

Germany www.esta.com

Transfer or reproduction of this document, or the use or communication of its content, is forbidden

without explicit consent. Violators will be liable for damages. All rights to patent, utility or design

registration are reserved.

The warranty can only be accepted if the following conditions are met:

- Professional transport

- Professional assembly, commissioning and operation using these operating instructions.

Verifiable compliance with the prescribed maintenance intervals.

- Operation of the product with conveyed media having the specified chemical and physical

properties.

- Immediate reporting of damage to the manufacturer.

- Exclusive use of genuine replacement parts.

- Structural modifications to the original condition only to be carried out with the agreement and

written approval of the manufacturer.

General instructions

60000-52-03

DDE 1500

1. General instructions ...................................................................................................... 4

1.1 Target group ........................................................................................................... 4

1.2 Tips ........................................................................................................................ 4

2. Product identification .................................................................................................... 5

2.1 Technical data ........................................................................................................ 5

2.2 Intended application ............................................................................................... 6

3. Product description ....................................................................................................... 7

3.1 Product illustration of DDE 1500 ............................................................................ 7

3.2 Functional description ............................................................................................ 8

4. Safety instructions ........................................................................................................ 9

4.1 Hazard categories .................................................................................................. 9

4.2 Symbol explanation ................................................................................................ 9

4.3 General safety instructions ................................................................................... 11

4.4 Fire hazard prevention ......................................................................................... 11

4.5 Preventing mechanical hazards ........................................................................... 12

4.6 Preventing electrical hazards ............................................................................... 13

4.7 Preventing dust hazards ....................................................................................... 14

5. Delivery and commissioning ...................................................................................... 15

5.1 Delivery and transport .......................................................................................... 15

5.2 Connection ........................................................................................................... 16

5.3 Function check ..................................................................................................... 18

5.4 Commissioning ..................................................................................................... 19

5.5 Suction line connection ........................................................................................ 19

5.6 Troubleshooting during commissioning ................................................................ 20

6. Operating instructions ................................................................................................ 20

6.1 Switching the product on ...................................................................................... 20

6.2 Operating the product ........................................................................................... 20

7. Maintenance & troubleshooting ................................................................................. 22

7.1 Maintenance instructions ...................................................................................... 22

7.2 Inspection and maintenance intervals .................................................................. 23

7.3 Emptying the disposal unit.................................................................................... 24

7.4 Locating the collection drawer with the adjusting screw ....................................... 24

7.5 Dismantling the outlet element filter mat .............................................................. 25

7.6 Replacing filter cartridges ..................................................................................... 26

7.7 Cleaning the product ............................................................................................ 28

7.8 Storing the product ............................................................................................... 28

7.9 Rectifying faults .................................................................................................... 29

8. Disposal ....................................................................................................................... 31

8.1 Disposal of collected material ............................................................................... 31

8.2 Disposal of the filter cartridge ............................................................................... 31

8.3 Disposal of the product ......................................................................................... 31

9. Optional equipment ..................................................................................................... 32

9.2 Dust Class H post-filter cassette .......................................................................... 32

10. Declaration of incorporation ...................................................................................... 33

Notes ................................................................................................................................... 35

General instructions

DDE 1500

60000-52-03

1. General instructions

1.1 Target group

These instructions are intended for

 Skilled warehousing and logistics personnel responsible for transport

 Operators trained on the product who are familiar with the extraction

process,

 Service, cleaning and maintenance staff trained on the product.

 Trained electrical specialists.

1.2 Tips

Before operation, all persons who are to use the product or perform maintenance

on it must be provided with information, instructions and training in the

substance(s) for which it is to be used, including the procedure for safe disposal of

the collected material. Responsibilities must be clearly established on site for the

following

 Assembly

 Commissioning

 Operation

 Maintenance and repairs

 Disposal

Read the instructions carefully before working with the product.

The product may only be used by persons who have been instructed in its handling

and are explicitly authorised to use it.

Always keep the instructions at the place where the product is being used, so that

they can be seen by personnel at all times.

These instructions describe the product at the time of first delivery following

manufacture.

 Keep the documents throughout the product's service life.

 Pass these and other supplementary documents on to any subsequent

owners or users.

 Add all changes to the documents that they receive.

Check the completeness of the documents and pay attention to their content.

Product identification

60000-52-03

DDE 1500

2. Product identification

2.1 Technical data

We reserve the right to make technical changes.

Item no.

60.000

60.000.002

Type DDE 1500

DDE 1500

DDE 1500 Alu-Mix

Nominal frequency

[Hz]

Drive power

[kW]

1,1

Connection voltage

[V]

400 / 460

Nominal current

[A]

2,20

2,45

2,15

2,40

Circuit breaker

[A]

C16A (Automat)

Protection class

IP 55

Max. vacuum

[Pa]

1.950

2.750

1.950

2.750

Max. airflow volume

[m³/h]

1.450

1.700

1.300

1.550

Compressed air connection

bar

4-6

average sound pressure level LpA*

[dBA]

71,5

75,5

64,5

69,5

Dimensions L x W x H

(including filter unit)

[mm]

650 x 710 x 1.455

650 x 710 x 1.860

Ambient temperature

[°C]

540

Rel. humidity

[%]

30 - 70

min. spatial requirement around the

product

Operator's side (front)

Inlet

Outlet

Rear

Top

[mm]

1.000

500

1.000

Total weight (including filter unit)

[kg]

160

195

Production year

see type plate

* Using the enveloping surface method DIN EN ISO 3744, measured at minimum volume flow; noise measurement margin of

error approx. 4 dBA

** Custom voltage on request

Product identification

DDE 1500

60000-52-03

2.2 Intended application

2.2.2 Intended use

The product has been manufactured based on state-of-the-art technology and

according to recognized safety regulations and must be used as intended:

 For permanent connection to a Lissmac processing machine

 Only functional as a dust extractor in conjunction with an appropriate filter

unit from the DDE 1500 series.

 As a fan unit for a modular dust extraction concept.

 For commercial use, such as in industrial enterprises and workshops.

 For extraction in individual workplaces.

 Only for dry cleaning.

 As a central extraction system on dust-generating machinery.

 As a central extraction system on chip-generating machinery.

 As a central extraction system on machines which produce swarf and chips.

Other applications are considered unintended use. LISSMAC is not liable for

damages due to unintended use!

2.2.3 Improper use

The product has been manufactured according to the state of the art and

recognized safety regulations. Unintended use may cause hazards.

Therefore:

 Do not operate without an appropriate filter unit from the DDE 1500 series.

 Do not use or store outdoors or in wet conditions.

 Do not change the location of the product during suction operation.

 Do not set up or operate in dust/gas-explosive areas.

 Do not use in painting operations.

 Do not use for the extraction of aluminium or highly alloyed steel dust.

 Do not connect to processing machines that may produce active ignition

sparks or hot embers.

 Do not suck up liquids.

 Do not suck up aggressive gases.

 Do not suck up any readily flammable or glowing particles.

2.2.4 Reasonably foreseeable misuse

 Do not suck up hot embers, such as cigarette butts.

 Do not cause complete closure of the suction openings.

Product description

60000-52-03

DDE 1500

3. Product description

3.1 Product illustration of DDE 1500

Fan unit

Disposal unit

Opening of

intake port

Filter unit

Cleaning unit

Outlet element

Transport lugs

Compressed air

connection

Product description

DDE 1500

60000-52-03

3.2 Functional description

The fan unit can be combined with different filter units from the DDE 1500 series. It

is equipped with a three-phase motor which drives a radial fan. The fan unit is

supplied with or disconnected from the required power via the connection to the

Lissmac main system.

Due to the negative pressure produced by the fan, air is sucked in through the

corresponding filter unit. Permanent filters located in the filter unit separate the dust

from the air that is sucked in. The purified air is fed back into the room through the

outlets on the top of the fan unit.

The filter cartridges are manually cleaned with compressed air. Compressed air is

fed into the rotating cleaning device in the product's filter unit via the compressed air

connection. The filters are freed from dust and regenerated as a result of this

cleaning.

The disposal unit attached below the filter collects the dust that has been cleaned

off. The collection drawer is lowered and pulled out for easier disposal of the collected

material.

Safety instructions

60000-52-03

DDE 1500

4. Safety instructions

4.1 Hazard categories

Safety instructions and cross-topic information are indicated in this manual by

symbols.

Based on the severity of the hazard, the hazard warnings are categorized as

follows:

DANGER

Hazard warning about an immediate danger to people.

Failure to comply can lead to severe injury or death.

WARNING

Warning about a recognisable hazard.

Failure to comply can lead to severe injury or death, and can destroy the product

or parts of it.

CAUTION

Instruction about a hazard.

Failure to comply can lead to slight injury and to damage to the product.

4.2 Symbol explanation

Further information

Reference to legal regulations

Safety instructions

DDE 1500

60000-52-03

4.2.1 Symbols on the product

Before commissioning, read and observe the installation instructions and safety

instructions (per ISO 11684)

1. Switch the product off.

2. Wait 5 minutes.

3. Then pull out the collection

drawer or open the product.

Do not take in glowing dust or other sources of ignition. Do not use in conjunction

with spark-generating machinery.

Safety instructions

60000-52-03

DDE 1500

4.3 General safety instructions

During extraction, the volume flow returned from the product into the room should

be no more than 50% of the air supplied. With open room ventilation, supply air

flow should be assumed as equal to the room volume every hour. This means that

the rate of air replacement must be once per hour.

Supply air flow [m³/h] = room volume [m³]  air replacement rate [1/h]

Example:

When the product is operating at the nominal airflow volume of 1,060 m³/h, the

same volume of fresh air must be fed in. This occurs with natural ventilation if the

volume of the work room is 1,060 m³ (e.g., 353 m² surface with a 3 m ceiling

height).

According to work equipment user directives 2009/104/EG and TRGS 560, safety

devices for prevention or removal of hazards must be regularly maintained and

regularly inspected by an expert for safe, flawless operation.

In all emergencies, the product must be disconnected from the power supply

immediately, turned off at the main switch and the plug pulled immediately.

4.4 Fire hazard prevention

A cyclone can separate sparks and glowing particles but the manufacturer does

not guarantee any protection from fire as a result. Spark detection and quenching

systems adapted to the application can be provided for this.

DANGER

Danger of fire due to sparks and glowing particles

 If there is a fire, alert the fire department immediately, and contain the fire

by appropriate means.

 Keep a suitable extinguishing agent near the product before start-up and

during operation.

Safety instructions

DDE 1500

60000-52-03

4.5 Preventing mechanical hazards

CAUTION

Injuries from crushing

 Make sure that the surface can be driven on, is level and sufficiently load

bearing.

 Do not park on a sloping floor.

 Always wear safety shoes when moving the device!

 Watch out for pipe or hose connections and other valves, or disconnect if

required.

WARNING

Crushing hazard due to loose or open covers during operation

 Keep covers tightly closed during operation!

WARNING

Risk of tripping due to inattentiveness and when the collection drawer is pulled out.

 Always pay attention to the local accident prevention regulations.

 Keep a distance from the product when you are not working with it.

 Always push the collection drawer back in after visual inspection and

emptying.

WARNING

Risk of falling due to improper handling of the transport lugs.

 Always pay attention to the local accident prevention regulations.

 Only attach the permitted transport aids and lifting tools to the transport lugs.

All movable machine parts driven by electric motors must be covered by fixed,

securely fastened protective covers that can be removed only with tools.

The compressed air must be disconnected after use, before moving the device to

another site and before cleaning, maintenance, or replacement or removal of

movable parts.

Safety instructions

60000-52-03

DDE 1500

4.6 Preventing electrical hazards

DANGER

Electric shock from high voltages

 Follow the safety rules for working with electrical products!

 Secure the product from being switched on.

 Render the product voltage-free by switching off the main system!

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

DANGER

Electric shock from high voltages when power cable is damaged

 Do not damage by running over, crushing, straining, etc.

 Regularly check the power cable for damage and ageing.

 Do not use if damage has been found on the power cable!

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

 Use only original LISSMAC replacement parts.

DANGER

High-voltage electric shock when working on the running product

 Switch off the product via the main system and secure it from being

switched on again.

 Render the product voltage-free by switching off the connected main

system!

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

DANGER

Residual hazard from loose or open covers

 Keep covers closed during operation!

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

All electrical parts must be covered by fixed, securely fastened protective covers

that can be removed only with tools. The product complies with Protection Class I

according to EN 60335.

After use, before moving the product to another site and before cleaning,

maintenance, or replacement or removal of movable parts, switch off the product

at the main switch and render it voltage-free.

Safety instructions

DDE 1500

60000-52-03

4.7 Preventing dust hazards

CAUTION

Damage due to dust release

 Maintenance, cleaning, repair and emptying work may be done only by

expert personnel.

 Wear personal protective equipment.

- Respirator mask (particle filter class P3)

- Protective clothing

- Protective gloves

- Eye protection

 Set up locally filtered forced-air ventilation where the product is being

maintained, inspected or cleaned.

 Operate the product only with the complete filtration system.

 Seal the intake port with a sealing plug so it is dust-tight when transporting.

CAUTION

Damage due to dust build-up in the pipe system

 Check the connected piping system regularly for dust deposits.

 Observe the minimum air speed required for your application and the

resulting minimum airflow volume.

When opening and emptying the collection drawer, dust

inhalation cannot be ruled out. That is why all servicing, cleaning

and maintenance procedures, including the emptying of the

collection drawer, are only to be performed by specialist

personnel with personal protective equipment.

The people assigned to cleaning work must be instructed with

regard to the aspirated toxic materials. Harm to bystanders and

the environment must be prevented by all means. After the

maintenance has been carried out, the maintenance area must

be thoroughly cleaned.

Delivery and

commissioning

60000-52-03

DDE 1500

5. Delivery and commissioning

5.1 Delivery and transport

DANGER

Danger from falling product

 Do not walk under heavy loads.

 The lifting and transporting equipment must be designed for the weight of

the product.

WARNING

Crushing hazard if the product settles during transport

 Secure the product during transport.

 Wear safety shoes.

CAUTION

Risk of damaging the product due to improper transport.

 Do not push the product over the floor if it does not have any rollers.

 Use only suitable lifting and transport equipment (such as a forklift or lift

truck) when transporting the product to its set-up location.

 Watch out for the centre of gravity – which is not in the middle – when

lowering the machine.

 Make sure the floor has adequate weight capacity and can be properly

driven on when transporting the product.

 Products with feet or recesses for fork-lift trucks must always be dowelled

to the floor.

Upon delivery inspect the product for transportation damage. Damage

determined must be reported and documented immediately.At delivery,

the product is fastened to a pallet.

 Remove the protective cover and floor securing devices.

 Check the delivery is complete

 Pay attention to the weight of the product and its centre of gravity

during all transport work.

 Hang the product using sling gear (e.g. a lifting belt, round sling)

at the positions provided, lift it from the pallet and set it down

immediately on the floor next to the pallet.

 Lift the product from the pallet using a forklift at the positions

provided and set it down immediately on the floor next to the

pallet.

Delivery and

commissioning

DDE 1500

60000-52-03

5.2 Connection

5.2.1 Electrical connection

DANGER

Electric shock from high voltages

 Avoid damage to the power cable caused by running over, crushing or

straining it.

 Regularly check the power cable for damage and wear.

 Do not start up if damage has been found on the power cable!

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

 Use only original replacement parts.

Before establishing cable connections between the product and the mains, it is

essential to check that the operating voltage specified on the rating plate matches

that of the mains.

DANGER

Electric shock from high voltages

 Follow the safety rules for working with electrical products!

 The product must be secured from being switched on again while work is

being carried out on it.

Place the device horizontally on an even surface as close as possible to the dust

source.

Connection to the building's power supply is made at the installation location.

DDE 1500

Mains (standard)

3~PEN /

3~PE+N

Three-phase current

400V/50Hz 3N~

Fuse

[Amp.]

C16A (circuit breaker)

* Custom voltage on request; observe the specifications on the rating plate.

Delivery and

commissioning

60000-52-03

DDE 1500

5.2.3 Pneumatic connection

Compressed air is required for the manual rotary cleaning of the filter elements in

the filter unit. Connect oil and water-free compressed air to ensure operational

safety and machine availability.

Connection to the compressed air supply (compressor) is made at the installation

location.

DDE 1500

Compressed air quality (ISO 8573-

1:2010-04)

Class 3.2.2

Pressure

[bar]

4 - 6

Connection-ø

['']

¼ (ø9mm)

5.2.4 Activation operations for motors:

Motors with high output without frequency converters should be not be switched on

and off within a short period of time too frequently. Otherwise, electrical

components could overload as a result. Please observe the table for activation

operations:

Motor output (kW)

Activation operations per hour

1 – 4

Up to 8 starts

4 – 7,5

Up to 6 starts

7,5 – 15

Up to 4 starts

15 – 30

Up to 3 starts

From 30

Electronically controlled overrun time

Delivery and

commissioning

DDE 1500

60000-52-03

5.3 Function check

Before the product is first used, a function check must be performed.

Operate the main switch on the main system to carry out a functional test of the

product.

5.3.1 Rotation direction monitoring

DANGER

Electric shock from high voltages

 Any work on the electrical grid and on live components parts may only be

performed by an electrician.

When the direction of rotation is incorrect, the product becomes impermissibly hot,

the volume increases, the airflow volume falls, and the product’s suction

performance suffers. Damage to the product cannot be ruled out.

After first switching on the product, you should check that the fan rotor’s direction

of rotation is correct.

1. Switch on the product using the main switch on the connected system.

2. Check the direction of rotation of the fan impeller.

3. If the direction of rotation is incorrect, have phases L1 and L3 reversed by

an electrical technician.

4. Switch the connected main system on again.

5. The product is ready for operation.

Delivery and

commissioning

60000-52-03

DDE 1500

5.4 Commissioning

Use original accessories.

Once a functional inspection has been completed, the connection is made to the

processing apparatus that is to be extracted.

1. Disconnect the product from the compressed air supply.

2. Switch the product off at the connected main system.

3. Place the product on an even surface as close as possible to the work

station.

4. Switch the product on again at the connected main system.

5. Connect the compressed air.

5.5 Suction line connection

Connect the processing machine to be vacuumed to the filter unit's

intake port through a pipeline.

For a suction line, use

 a pipeline with a length of 3 m that meets the national

requirements for this application.

 an appropriate pipe (wrap fold) that meets the national

requirements for this application.

 approved adapters for short diameter on the connection

piece

If the pipe diameter is increased or the pipeline lengthened, it cannot be

guaranteed that no dust deposits will collect in the pipeline.

Observe the minimum air speed necessary for your application. Regularly check

the pipeline for dust deposits.

Operating instructions

DDE 1500

60000-52-03

5.6 Troubleshooting during commissioning

Fault

Possible cause

Possible solution

The motor shuts down

before reaching the

operating speed.

The switching products

present (main system) are

incorrectly set up or are

unsuitable.

Check the direction of

rotation and have phases

reversed by an electrical

technician if necessary.

Motor power consumption

is too high.

Direction of motor rotation

is incorrect.

The phases in the mains

power cable may only be

changed by an electrical

technician.

The desired air quantity is

not reached

The supply cable's

preliminary fuse has

tripped.

Motor was switched on/off

too often within a short

period of time.

Please consult the

"Activation operations for

motors" table.

6. Operating instructions

6.1 Switching the product on

Before starting work, check that the product is in a proper and safe condition.

The compressed air supply (4-6 bar) must be connected.

Switch the product on at the connected main system.

6.2 Operating the product

After connecting the suction hose to the dust source:

1. Switch the product on at the main system.

2. Start processing machine / extraction element.

3. Start the processing operation.

The location of the product must not be changed during operation.

When finishing the processing operation:

1. End the processing operation.

2. Switch off processing machine / extraction element.

3. Take the product out of operation using the connected main system.

Page is loading ...

Esta 60.000 Owner's manual

Brand: Esta

Model: 60.000

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Esta 60.000 Owner's manual

This manual is also suitable for

Esta 60.000 Owner's manual

Other documents