New Classic FURNITURE Bella Installation guide

Type
Installation guide
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the PARTS LIST and/or HARDWARE LIST shown below.
Caution: Please read the instructions thoroughly before assembly.
1. We recommend that you assemble this product with the assistance of another person; this will make the
assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
2. Please do not over tighten screws or bolts until the assembly is completed.
3. Please put all parts on a non-abrasive floor before assembly,and follow the assembly steps to assemble
your newly purchased product correctly and efficently.
Assembly Instructions
MADE IN VIETNAM PAGE: 1 OF 4
ITEM NO. D324-3P
BELLA COUNTER SOFA TABLE WITH
2 STOOLS & USB PORT
PARTS LIST
NO.
A
COMPONENT SKETCH QTY.
2 PCS
B2 PCS
SHORT SIDE
STRETCHER
2 PCS
F2 PCS
D
LEG (Right)
2 PCS
C
CUSHION SEAT
4 PCS
NO.
1FLAT WASHER
1/4” DIA.
SPRING
WASHER
1/4” DIA.
HARDWARE LIST
COMPONENT SKETCH QTY.
16 PCS
216 PCS
316 PCS
412 PCS
WOOD SCREW
#8 x 1 1/2” L
51 PC
E
LONG SIDE
STRETCHER
LEG
LEG (Left)
BOLT
1/4” x 2 1/4
ALLEN KEY
M4
MADE IN VIETNAM PAGE: 2 OF 4
Assembly Instructions
STEP 3
STEP 1 STEP 2
ITEM NO. D324-3P
BELLA COUNTER SOFA TABLE WITH
2 STOOLS & USB PORT
3
5
2
1
A
B
X4
A
B
C
C
4
X2
A
BC
C
D
E (Right)
F (Left)
5
3
2
1
X4
4
X4
Assembly Instructions
MADE IN VIETNAM PAGE: 3 OF 4
ITEM NO. D324-3P
BELLA COUNTER SOFA TABLE WITH
2 STOOLS & USB PORT
PARTS LIST
NO.
A
COMPONENT SKETCH QTY.
1 PC
B1 PC
1 PC
D
LEG (Right)
2 PCS
C
TABLE TOP
1 PC
NO.
1FLAT WASHER
5/16” DIA.
SPRING
WASHER
5/16” DIA.
HARDWARE LIST
COMPONENT SKETCH QTY.
6 PCS
26 PCS
36 PCS
46 PC S
WOOD SCREW
#8 x 1 1/2” L
51 PC
E
SUPPORT ROD
LEG (Left)
BOLT
5/16” x 1 3/4
ALLEN KEY
M4
TABLE
STRETCHER
MADE IN VIETNAM PAGE: 4 OF
Assembly Instructions
ITEM NO. D324-3P
BELLA COUNTER SOFA TABLE WITH
2 STOOLS & USB PORT
A
B (Left)
C (Right)
D
A
532 1
X3
4
E
A
B (Left)
E
4
A
E
X2
X4
D
D
D
Attach Left Leg(B), Right Leg (C) to Table Top (A)
by using Flat Washer (1), Spring Washer (2) and
Bolt (3).
Attach Table Stretcher (E) to Left Leg (B), make
sure the wooden dowel is completely pushed
into position.
Attach Support Rod (D) to Table Top (A)
and Table Stretcher (E).
C (Right)
C (Right)
B (Left)
STEP 1
STEP 3 STEP 4
Attach Table Stretcher (E) to Right Leg (C), screw in
all Wood Screw (4), make sure they are completely
pushed into position. Then your product is ready
for you to enjoy.
STEP 2
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

New Classic FURNITURE Bella Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI