M-ELEC M-ELEC ML-MR8-M-RF 8W Multi LED Downlight User manual
- Type
- User manual
The M-ELEC M-ELEC ML-MR8-M-RF 8W Multi LED Downlight is a versatile and energy-efficient lighting solution for a variety of applications. With a low profile design, it can be installed under trusses and frames, making it ideal for use in tight spaces. It features an on-board driver with improved dimming capabilities and a recessed face for a clean and modern look. It has an IP40 rating at the back and an IP54 rating at the front, making it suitable for use in both indoor and outdoor applications.
The M-ELEC M-ELEC ML-MR8-M-RF 8W Multi LED Downlight is a versatile and energy-efficient lighting solution for a variety of applications. With a low profile design, it can be installed under trusses and frames, making it ideal for use in tight spaces. It features an on-board driver with improved dimming capabilities and a recessed face for a clean and modern look. It has an IP40 rating at the back and an IP54 rating at the front, making it suitable for use in both indoor and outdoor applications.
8W MULTI LED DOWNLIGHT
* With an on-board driver
** Fits under majority of trusses
ELIMINATES
PLUG BASES
COMPATIBLE WITH
MAJOR DIMMERS
FITS UNDER
TRUSSES
OUR SLIMMEST
DOWNLIGHT **
*
ALSO AVAILABLE WITH
44mm
The new MR8-M-RF features a low profile body to allow installation under trusses and frames while receiving an
updated on-board driver with improved dimming capabilities and a recessed face.
MR8-M-RF includes an IC-4 rating which allows it to rest against, and be covered with, suitable insulation.
*RAPID version available
ML-MR8-M-RF
Product information
TECHNICAL INFORMATION
Total Power: 8W*
Lumen Output: WW 710lm | NW 792lm | W 737lm
Colour Temp: WW 3000K NW 4000K W 5700K
IP Rating: IP40 Back
IP54 Front
89-105lm/w
CRI: 80+
Beam Angle: 110°
Dimmable: Yes (Triac)
Integrated
Average Life: 50,000 hrs**
Double Insulated Ye s
Power Factor
Dimensions: Base: Diameter 110mm | Depth 44mm*** | Cut out 90mm
5 Years
*Total power consumed including driver
** Average life is calculated on expected average lifespan
*** Total depth measured from front of mounting surface to top of heat sink
Downlight
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
• Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
• Disconnect power before installing or servicing
• All components must not be mechanically stressed
• 000)
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
• Insulation distance: Building insulation and building elements may abut the luminaire on the sides and/or the top.
• The light source of this luminaire is not replaceable - the whole luminaire should be replaced.
• The flexible cord that is damaged can only be replaced by the manufacturer, its service agent, or a similarly qualified person.
T. 1300 222 445 | www.melec.com.au For further information about our warranties please go to: melec.com.au/legal/warranties
INSTALLATION GUIDE
1. Before commencing installation or maintenance, ensure electricity is switched off at the mains
2. Remove existing downlight and disconnect old transformer OR for new installations mark and cut out
90 mm hole in ceiling
3. Set the desired colour output with the “selector switch” on the back of the downlight head (see
picture beside)
4. Plug unit into a suitable surface socket OR connect the rapid connector onto the cable
5. Carefully bend spring clips upwards and install new LED downlight
The new MR8-M features a low profile body to allow installation under trusses and frames while receiving an
updated on-board driver with improved dimming capabilities.
MR8-M includes an IC-4 rating which allows it to rest against, and be covered with, suitable insulation.
ML-MR8-M-RF-RAPID
Product information
TECHNICAL INFORMATION
Total Power: 8W*
Lumen Output: WW 710lm | NW 792lm | W 737lm
Colour Temp: WW 3000K NW 4000K W 5700K
IP Rating: IP40 Back
IP54 Front
89-105lm/w
CRI: 80+
Beam Angle: 110°
Dimmable: Yes (Triac)
Integrated
Average Life: 50,000 hrs**
Double Insulated Ye s
Power Factor
Dimensions: Base: Diameter 110mm | Depth 44mm*** | Cut out 90mm
5 Years
*Total power consumed including driver
** Average life is calculated on expected average lifespan
*** Total depth measured from front of mounting surface to top of heat sink
Downlight
T. 1300 222 445 | www.melec.com.au For further information about our warranties please go to: melec.com.au/legal/warranties
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
• Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
• Disconnect power before installing or servicing
• All components must not be mechanically stressed
• 000)
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
• Insulation distance: Building insulation and building elements may abut the luminaire on the sides and/or the top.
• The light source of this luminaire is not replaceable - the whole luminaire should be replaced.
• The flexible cord that is damaged can only be replaced by the manufacturer, its service agent, or a similarly qualified person.
1. Before commencing installation or maintenance, please ensure electricity is switched off
at the mains.
2. Remove existing downlight or mark and cut appropriate hole in ceiling.
3. Set the desired colour output with the selector switch on the back of the downlight head.
4. Install Rapid ® connector, see next page for instructions.
5. Carefully bend spring clips upwards and install the LED Downlight.
6. Test.
DOWNLIGHT INSTALLATION INSTRUCTIONS
LED DOWNLIGHT
SPRING CLIPS
RAPID CONNECTOR
T. 1300 222 445 | www.melec.com.au For further information about our warranties please go to: melec.com.au/legal/warranties
Follow the below steps to connect the Rapid® connector and downlight to an input TPS cable.
1. Slide the cover back until you can remove it completely.
2. For 1.5mm cable* place the cable into the channel and push it down so it’s
completely flat.
OR
3. For 2.5 mm cable*, remove the insert in the centre.
4. Place the cable* into the channel and push it down so it is completely flat.
5. Align the lid pins with the channel grooves.
6. Use a steady firm motion and slide the cover closed until you hear a ‘click’ sound.
This indicates the unit is now installed securley.
7. OPTIONAL: Fix the rapid connector into place using suitable fixing screws or the
cable tie loops.
RAPID® CONNECTOR INSTALLATION INSTRUCTIONS
UNIVERSAL POLARITY SAFE.
L & N are interchangable.
* Suitable for use with 1.5mm and 2.5mm 2C+E ONLY WITH CENTRE EARTH cables in accordance with AS/NZS 5000.2:2006 conductor range.
PLEASE NOTE!
1. Strip 15mm of the outer cable insulation exposing the inner insulated wires.
2. Insert active, earth and neutral insulated cables* into the slots on the terminator block.
3. Clip the terminator block in the top end of the channel ensuring the cable* is sitting flat in the channel.
4. Place the cover on top of the main body and press the pins firmly into the channel grooves. Slide lid forwards until you hear a 'click’ sound. This
indicates the unit is now installed securley.
TERMINATION GUIDE FOR RAPID® CONNECTOR
1
5
mm
1. Insert a small flat bladed screwdriver into position 'A' and lift slightly.
2. Slide the cover back until you can remove it completely.
UNLOCKING GUIDE FOR RAPID® CONNECTOR
A
T. 1300 222 445 | www.melec.com.au For further information about our Warranties please go to: melec.com.au/legal/warranties
at any time without notice. Please visit www.melec.com.au for the latest information on our products
A
ONSITE WARRANTY
EXCLUSIVE TO
MEMBERS ONLY
FREE
MEMBERS ONLY
MEMBERS ONLY
F
F
R
R
E
E
E
E
O
O
N
N
S
S
I
I
T
T
E
E
W
W
A
A
R
R
R
R
A
A
N
N
T
T
Y
Y
F
F
O
O
R
R
3
3
Y
Y
E
E
A
A
R
R
S
S
I
I
N
N
C
C
L
L
U
U
D
D
E
E
S
S
P
P
A
A
R
R
T
T
S
S
&
&
L
L
A
A
B
B
O
O
U
U
R
R
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
I
n
n
c
c
o
o
n
n
j
j
u
u
n
n
c
c
t
t
i
i
o
o
n
n
w
w
i
i
t
t
h
h
y
y
o
o
u
u
r
r
s
s
t
t
a
a
n
n
d
d
a
a
r
r
d
d
p
p
r
r
o
o
d
d
u
u
c
c
t
t
w
w
a
a
r
r
r
r
a
a
n
n
t
t
y
y
Version 1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
M-ELEC M-ELEC ML-MR8-M-RF 8W Multi LED Downlight User manual
- Type
- User manual
The M-ELEC M-ELEC ML-MR8-M-RF 8W Multi LED Downlight is a versatile and energy-efficient lighting solution for a variety of applications. With a low profile design, it can be installed under trusses and frames, making it ideal for use in tight spaces. It features an on-board driver with improved dimming capabilities and a recessed face for a clean and modern look. It has an IP40 rating at the back and an IP54 rating at the front, making it suitable for use in both indoor and outdoor applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Eurolux D108SC Owner's manual
-
-
Martec TLDD34523WD Operating instructions
-
Melec ML-MRWPB-120-M User manual
-
-
Melec ML-MRSLB-60-M Installation guide
-
Martec TLTD34510MD Operating instructions
-
Martec TLAM34510WD Operating instructions
-
Melec ML-BKT-FWSB User manual
-
GreenBrook V7T3000W Operating instructions
