Asus PE1100N User manual

PE1100N Series

Embedded Computer

User Manual

COPYRIGHT INFORMATION

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by

any means, except documentation kept by the purchaser for backup purposes, without the express

written permission of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS,

LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR

PRODUCT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to

the owners’ benefit, without intent to infringe.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND

SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR

LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE

PRODUCTS AND SOFTWARE DESCRIBED IN IT.

LIMITATION OF LIABILITY

Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to

recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled

to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including

death) and damage to real property and tangible personal property; or any other actual and direct

damages resulted from omission or failure of performing legal duties under this Warranty Statement,

up to the listed contract price of each product.

ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort

or infringement under this Warranty Statement.

This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its

suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY

CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3)

SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES

(INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS

INFORMED OF THEIR POSSIBILITY.

SERVICE AND SUPPORT

Visit our multi-language website at https://www.asus.com/support/

First Edition

September 2023

E22181

PE Series

3

Contents

About this manual .............................................................................................................5

Conventions used in this manual ......................................................................................... 6

Package contents ..............................................................................................................7

Chapter 1: Getting to know your Embedded Computer

1.1 Features ......................................................................................................................10

1.1.1 Front view ....................................................................................................................... 10

1.1.2 Rear view ......................................................................................................................... 13

1.1.3 Left view .......................................................................................................................... 18

1.1.4 Right view ....................................................................................................................... 20

1.2 Motherboard overview .........................................................................................21

1.2.1 Motherboard layout .................................................................................................... 21

1.2.2 Internal connectors ..................................................................................................... 23

Chapter 2: Using your Embedded Computer

2.1 Getting started ......................................................................................................... 28

2.1.1 Connect the AC power adapter to your Embedded Computer .................. 28

2.1.2 Connect a display panel to your Embedded Computer ................................ 30

2.1.3 Connect the USB cable from keyboard or mouse ............................................ 31

2.1.4 Turn on your Embedded Computer ...................................................................... 32

2.2 Turning off your Embedded Computer...........................................................33

Chapter 3: Upgrading your Embedded Computer

3.1 Removing the bottom cover ............................................................................... 36

3.2 Replacing the bottom cover ...............................................................................37

3.3 Installing a nano SIM card (optional) ...............................................................38

3.4 Installing an M.2 (E-key) module .......................................................................40

3.5 Installing an M.2 (M-key) module ...................................................................... 42

3.6 Installing an M.2 (B-key) module .......................................................................44

3.7 Installing antennas (optional) ............................................................................. 48

3.8 Installing wall mount brackets (optional) ......................................................51

3.9 Mounting to a surface (optional).......................................................................52

3.10 Installing DIN rail clips (optional) ......................................................................53

3.11 Installing the terminal block (optional) ...........................................................54

4

PE Series

Chapter 4: Setting up your Embedded Computer

4.1 Requirements ...........................................................................................................56

4.2 Installing or Updating the OS .............................................................................56

Appendix

Safety information .............................................................................................................60

Setting up your system ............................................................................................................ 60

Care during use ........................................................................................................................... 61

Regulatory notices ............................................................................................................63

Service and Support .........................................................................................................75

PE Series

5

About this manual

This manual provides information about the hardware and software features

of your Embedded Computer, organized through the following chapters:

Chapter 1: Getting to know your Embedded Computer

This chapter details the hardware components of your Embedded

Computer.

Chapter 2: Using your Embedded Computer

This chapter provides you with information on using your Embedded

Computer.

Chapter 3: Upgrading your Embedded Computer

This chapter provides you with information on how to upgrade the

memory modules, wireless modules, and hard disk drive / solid state

drive of your Embedded Computer.

Chapter 4: Setting up your Embedded Computer

This chapter will guide you in setting up your Embedded Computer for

the first time.

Appendix

This section includes notices and safety statements your Embedded

Computer.

6

PE Series

Conventions used in this manual

To highlight key information in this manual, some text are presented as

follows:

IMPORTANT! This message contains vital information that must be

followed to complete a task.

NOTE: This message contains additional information and tips that can

help complete tasks.

WARNING! This message contains important information that must be

followed to keep you safe while performing certain tasks and prevent

damage to your Embedded Computer's data and components.

PE Series

7

Package contents

Your Embedded Computer package contains the following items:

PE1100N Series

Terminal blocks Terminal block power adapter

I/O port dust covers Wall mount kit with two (2) brackets

8

PE Series

NOTE:

• Some bundled accessories may vary depending on the model. For

details on these accessories, refer to their respective user manuals.

• Illustrations of the device and accessories are for reference only.

Actual product specifications may vary depending on the model.

• If the device or its components fail or malfunction during normal

and proper use within the warranty period, bring the warranty

card to the ASUS Service Center for replacement of the defective

components.

Optional items

4G LTE/5G NR antennas Wi-Fi antennas

DIN rail clips

1

Getting to know your

Embedded Computer

10

PE Series

1.1 Features

1.1.1 Front view

Power input jack

The supplied terminal block power adapter converts AC

power to DC power for use with this jack. Power supplied

through this jack supplies power to the Embedded

Computer.

WARNING! The power adapter may become warm to

hot when in use. Do not cover the adapter and keep

it away from your body.

Cellular Signal LED

The cellular signal LED indicates whether the Embedded

Computer is connected to a cellular network.

PE Series

11

Wi-Fi Signal LED

The Wi-Fi signal LED indicates whether the Embedded

Computer is connected to a wireless network.

Serial (COM/CAN) Signal LED

Each numbered LED indicates whether a device that is

connected to the corresponding serial (COM/CAN) port on

the back panel is communicating through the serial bus.

Power button

The power button allows you to turn the Embedded

Computer on or off. You can use the power button to put

your Embedded Computer to sleep mode or press it for

four (4) seconds to force shutdown.

USB 3.2 Gen 1 port

The USB 3.2 Gen 1 (Universal Serial Bus) port provides a

transfer rate up to 5 Gbit/s and a maximum of 5V/0.9A

output per port.

HDMI™ port

The integrated 19-pin HDMI™ (High Definition Multimedia

Interface) port with a receptacle connector to support

external display devices with the following resolutions:

SOM HDMI Spec Resolution

Jetson Orin™

NX

HDMI 2.0 Up to 3840x2160 @ 60Hz

Jetson Orin

Nano™

HDMI 1.4 Up to 3840x2160 @ 30Hz

LAN port

The 8-pin RJ-45 LAN port supports a standard Ethernet

cable for 10/100/1000Mbps connection to a local

network.

12

PE Series

Activity Link LED

Status Description

Off No link

Yellow Linked

Yellow (blinking) Data activity

Yellow (blinking then

steady)

Ready to wake

up from suspend

mode

Speed LED

Status Description

Off 10Mbps connection

Orange 100Mbps connection

Green 1Gbps connection

LAN port LED indications

ACT/LINK LED SPEED LED

LAN port

The 8-pin RJ-45 LAN port supports a standard Ethernet

cable for 10/100/1000Mbps connection to a local

network.

Functional Earth Ground

The Functional Earth Ground provides you with a

grounding point.

PE Series

13

1.1.2 Rear view

14

PE Series

Isolated DIO connector

The Isolated Digital Input/Output (DIO) connector

provides electrical isolation (up to 2500 VDC) of digital

input and output signals, which allow micro controllers

to detect and output logic states. The high voltage

protection can be used in industrial level uses. Please refer

to the illustration below for the Isolated DIO connector’s

pin definitions.

Signal Specifications

Digital

Input

I/O Mode DI

Sensor Type Dry contact

Wet contact (NPN or PNP)

Dry Contact On: short to GND

Off: open

Wet Contact On: 10-30 Vdc

Off: 0-0.8 Vdc

Digital

Output

I/O Mode DO

Sensor Type Sink

Voltage 24 Vdc nominal, open collector to 30 Vdc

Current Rating 200 mA per channel

Protection

Isolation IEC 60950-1:2005 + A1:2009+A2:2013: Hi-pot

2.5 kV

ESD IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV

EFT IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV

Surge IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV

PE Series

15

Serial (COM) connector

The 9-pin DB9 connector allows you to connect RS-232/

RS-422/RS-485 devices that have serial ports, such as

bar code scanner, modem, or printers. Please refer to the

table below for the pin definitions of the different COM

connectors.

NOTE: Default set to RS-232.

12345

6789

Pin RS-232 RS-422 RS-485

1NA TX- D-

2RXD TX+ D+

3TXD RX+ NA

4NA RX- NA

5GND GND GND

6NA NA NA

7RTS# NA NA

8CTS# NA NA

9NA NA NA

16

PE Series

Serial (CAN) connector (on selected models)

The 9-pin CAN Bus serial connector allows you to connect

devices with a CAN interface, such as an electronic control

unit (ECU). Please refer to the table below for the pin

definitions of the CAN Bus connector.

12345

6789

CAN Bus

1 NA

2 CAN_L

3 GND

4 NA

5 GND

6 NA

7 CAN_H

8 NA

9 NA

PE Series

17

WWAN-MIMO wireless antenna jack

The WWAN-MIMO antenna jack allows you to connect a

wireless antenna to enhance 5G NR MIMO signals.

NOTE: The 4G LTE/5G NR wireless antennas are

optional and may not come bundled.

WLAN Wireless antenna jack

The Wi-Fi wireless antenna jack allows you to connect a

wireless antenna for Wi-Fi signals.

NOTE: The Wi-Fi wireless antennas are optional and

may not come bundled.

18

PE Series

1.1.3 Left view

Debug console port (on selected models)

This micro USB port allows you to connect a computer

to the integrated USB to UART debug console (baud rate

115200) using a micro USB cable. Once connected to a

computer, you can start debugging without the need for

additional equipment.

Flash (USB 2.0 micro USB) port

This flash (micro USB) port allows you to connect to a host

computer to flash the OS image.

NOTE: The features on this side are covered with a metal cover. Ensure

to remove and replace the metal cover when accessing these features.

For more information on removing and replacing the metal cover, refer

to Installing a nano SIM card.

PE Series

19

Nano SIM card slot

This slot allows you to insert a Nano SIM card.

Force recovery pinhole

The hard reset pinhole allows you to put your Embedded

Computer into Force Recovery Mode to update or flash

the OS.

WWAN wireless antenna jack

The WWAN antenna jack allows you to connect a wireless

antenna to enhance 4G LTE/5G NR signals.

NOTE: The 4G LTE/5G NR wireless antennas are

optional and may not come bundled.

20

PE Series

1.1.4 Right view

Expansion slot

This slot allows you to install an ASUS Expansion Module

(AEM) for additional I/O ports.

NOTE: Contact your ASUS sales representative for

more information on AEMs.

Page is loading ...

Asus PE1100N User manual

Asus PE1100N User manual

in other languages

Related papers

Other documents