DeWalt DW896 TYPE 1 Owner's manual

Category
Power tools
Type
Owner's manual

This manual is also suitable for

DeWalt DW896 TYPE 1 is a 16-Gauge Nibbler designed to cut metal sheets with precision and ease. Its powerful motor and durable construction make it suitable for various metalworking applications, including HVAC, roofing, and fabrication. The tool features a versatile cutter that can be adjusted to cut in any direction, allowing for intricate cuts and shapes. With its compact size and lightweight design, the DW896 is easy to maneuver and control, even in tight spaces.

DeWalt DW896 TYPE 1 is a 16-Gauge Nibbler designed to cut metal sheets with precision and ease. Its powerful motor and durable construction make it suitable for various metalworking applications, including HVAC, roofing, and fabrication. The tool features a versatile cutter that can be adjusted to cut in any direction, allowing for intricate cuts and shapes. With its compact size and lightweight design, the DW896 is easy to maneuver and control, even in tight spaces.

Questions? See us on the World Wide Web at www_dewalt.corn
iNSTRUCTiON MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA
DE GARANTfA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
®
DW896
16-Gauge Nibbler
Grignoteuse de calibre 16
Cortadora de I_rnina calibre 16
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY DEWALTTOOL, CALL US TOLL FREE AT:
I=800=4=DEWALT (1=800=433=9258)
PADDLE
SWITCH
I
PUNCH
Irnportaret Safety Instructiores
_ WARNING: When using electric tools, basic safety precautions
should always be followed to reduce risk of fire, electric shock,
and personal inju_ including the following:
READ A££ INSTRUCTIONS
Double Iresulation
Double insulated tools are constructed throughout with two separate
layers of electrical insulation or one double thickness of insulation
between you and the tool's electrical system. Tools built with this
insulation system are not intended to be grounded. As a result, your
tool is equipped with a two prong plug which permits you to use
extension cords without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety
precautions when operating this tool. The insulation system is for
added protection against injury resulting from a possible electrical
insulation failure within the tool.
.&CAUTION: WHEN SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS. Repair or replace damaged cords.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on
equipment to reduce the risk of electric shock. When provided, this
plug will fit in the polarized outlet only one way. If the plug does not fit
fully into the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug
in any way.
Safety Instructieres For All Tools
* KEEP WORKAREA CLEAN. Cluttered areas and benches invite
injuries.
* CONSIDER WORKAREA ENVIRONMENT. Don't expose power
tools to rain. Don't use power tools in damp or wet locations. Keep
work area weft fit. Do not use tool in presence of flammable liquids
or gases.
* GUARD AGAINST ELECTRIC SHOCK. Prevent body contact
with grounded surfaces. For example; pipes, radiators, ranges, and
refrigerator enclosures.
* KEEP CHILDREN AWAY. Do not let visitors contact tool or
extension cord. Aft visitors should be kept away from work area.
* STORE IDLE TOOLS. When not in use, tools should be stored in
dry, and high or locked-up place -- out of reach of children.
* DON'T FORCE TOOL. It will do the job better and safer at the
rate for which # was intended.
* USE RIGHT TOOL. Don't force smafl tool or attachment to do the
job of a heavy-duty tool. Don't use tool for purpose not intended.
* DRESS PROPERLY. Do not wear loose clothing or jewelry. They
can be caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors. Wear
protective hair covering to contain long hair.
* USE SAFETY GLASSES. Also use face or dust mask if operation
is dusty.
* DON'T ABUSE CORD. Never carry tool by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil, and sharp
edges.
* SECURE WORK. Use clamps or a vise to hold work. It's safer than
using your hand and # frees both hands tooperate tool.
* DON'T OVERREACH. Keep proper footing and balance at aft
times.
* MAiNTAiN TOOLS WITH CARE. Keep tools sharp and clean for
better and safer performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords periodically and if
damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
* DISCONNECT OR LOCK OFF TOOLS when not in use, before
servicing, and when changing accessories, such as blades, bits,
cutters.
o
o
o
o
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of
checking to see that keys and adjusting wrenches are removed
from tool before turning it on.
AVOID UNINTENTIONAL STARTING. Don't carry tool with finger
on switch. Be sure switch is off when plugging in.
EXTENSION CORDS. Use only 3-wire extension cords that have
3-prong grounding-type plugs and 3-pole receptacles that accept
the tool's plug. Replace or repair damaged cords. Make sure your
extension cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and
nameplate ampere rating, ff in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts
120V
240V
Ampere Rating
More Not more
Than Than
0 6
6 10
10 12
12 16
Total Length of Cord in Feet
0-25 26-50 51-100 101-150
0-50 51-100 101-200 201-300
AWG
18 16 16 14
18 16 14 12
16 16 14 12
14 12 NotRecommended
OUTDOOR USE EXTENSION CORDS. When tool is used
outdoors, use only extension cords intended for use outdoors and
so marked.
STAY ALERT. Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
CHECK DAMAGED PARTS. Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction
manual.Havedefectiveswitchesreplacedbyauthorizedservice
center.Donotusetoolifswitchdoesnotturnitonandoff.
SAVE THESE INSTRUCTIONS
Motor
Your DEWALT tool is powered by a DEWALT built motor. Be sure your
power supply agrees with the nameplate marking. Voltage decrease of
more than 10% will cause loss of power and overheating. All DEWALT
tools are factory tested; if this tool does not operate, check the power
supply.
Switch
To start tool, depress the paddle switch (Figure 1). To turn the tool off,
release the paddle. The paddle switch can be locked on by engaging
the lock button located near the rear ofthe tool, while holding the paddle
depressed. Always be surethat the tool is not locked on before plugging
in. To turn the tool off when it is locked on, squeeze and release the
paddle once.
Setting the Cutter
TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY.
The cutter can be set to cut in any direction relative to the body. Release
the set screw in the knurled ring (Figure 2) with key provided and
unscrew the ring by rotating in a counterclockwise direction as viewed
from the cutter.
Loosen ring just enough to be able to rotate the die. Set the die so that
the connecting web (Figure 3) is on the opposite side of the direction of
cut. Fully tighten the knurled ring and lock by tightening the set screw.
Operation
NOTE: ALWAYS WEAR SAFETY GLASSES.
Make sure the knurled ring (Figure 2) is tight prior to use. Keep fingers
away from cutter and other moving parts.
BUTTON
FIG. 3
DIRECTION OF CUT
PADDLE SWITCH
FIG. 2
---DIE
CONNECTING
WEB
FIG.6
FIG.4
FIG.5
The nibbler cuts a slot in the work 6mm wide so remember to
compensate for this when marking out and calculating material
requirements.
When starting the cut from an edge, place the nibbler so the slot in the
die engages the work and the edge is against the punch, which is the
moving part when cutting (Figure 4).
Start the nibbler by depressing the paddle switch. Hold the body
parallel to the work surface.
Exert only enough forward pressure to start the nibbler cutting and
maintain this pressure. Extra pressure will not increase the rate of cut
as the amount of material removed at each cutting stroke is fixed and
the rate of cut is dependent only on the speed of the nibbler. The
cutting line of the work should be lightly coated with oil to lubricate the
punch and die while cutting.
NOTE: Punch and die should be lubricated by immersing in a good
quality cutting oil approximately every 30 feet of cutting.
When the cut is to be started or finished within the periphery of the
work, a 13mm (1/2") hole must first be drilled in the work at the start or
finish point. This enables the die to be entered or withdrawn as it is
larger in diameter than the slot being cut in the work (Figure 5).
Circular holes should be cut in the manner shown in Figure 6, starting
at the 13mm (1/2") diameter hole within the circle.
Punch and Die Replacement
After a period of cutting, the punch will become blunted and require
replacement. At the same time, check the die for sharpness and replace
if necessary.
To remove the die, release the knurled ring (Figure 7). Having removed
the die, rotate the motor by turning the armature fan, accessible through
the side cooling slot, until the punch retaining nut is clear of the face of
the gearbox. With the spanner provided, release this nut
counterclockwise and remove the punch, Figure 8.Assemble in reverse
order.
Keepyournibblerascleanaspossiblebywipingwithacleanclothand
occasionallyblowingairthroughit.
Cleaning
Blowing dust and grit out of the main housing by means of air hose is
recommended and may be done as often as dirt is seen collecting in
and around the ventilator vents. The motor should be running while air
is being blown into the air vents.
Lubrication
DEWALTtools are properly lubricated at the factory and are ready to
use. Tools should be relubricated regularly every 60 days to 6 months,
depending on usage. Tools used constantly on production or heavy-
duty jobs and tools exposed to heat may require more frequent
lubrication. This lubrication should only be attempted by trained power
tool repairmen such as those at DEWALTcertified service centers.
Motor Brushes
When the brushes on this tool become worn out, the tool will
automatically stop and prevent damage to the motor. Brush
replacement should be performed by DEWALT service centers.
Accessories
Recommended accessories for use with your tool are available at extra
cost from your distributor or local service center.
A CAUTION: The use of any non-recommended accessory may be
hazardous.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and replacement) should
be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
Three Year Limited Warranty
DEWALTwill repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This
FiG. 7
DiE
I
KNURLED RiNG
!
FiG. 8
--PUNCH
warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This
warranty does not apply to accessories or damage caused where
repairs have been made or attempted by others. This warranty gives
you specific legal rights and you may have other rights which vary in
certain states or provinces.
In addition to the warranty, DEWALTtools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your
DEWALT Power Tool, Laser, or Nailer for any reason, you can return it
within 90 days from the date of purchase with a receipt for a full refund
- no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-4-DEWALT for a free
replacement.
POUR TOUT RENSEIGNEMENT SUPPLE_MENTAIRE SUR CET
OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSER SANS
FRAIS LE NUMI_RO:
1 800 4-DEWALT (1 800 433-9258)
IINTERRUPTEUR ,_
PALETTE
I
POINOON
Irnportantes rnesures de s_curit_
_ VERTISSEMENT : Afin de r6duire les risques d'incendie, de
secousses electriques ou de blessures Iorsqu'on utilise des outils
61ectriques, il faut toujours respecter les mesures de securit6 suivantes.
LIRE TOUTES LES DIRECTIVES
Double isolation
Les outils & double isolation comportent deux couches distinctes
d'isolant 61ectrique ou une double _paisseur d'isolant qui prot_gent
I'utilisateur contre les risques de blessures provenant du syst_me
PARA REPARACION Y SERVIClO DE SUS HERRAMIENTAS
ELECTRICAS, FAVOR DE DIRIGIRSE AL CENTRO DE
SERVICIO IVlAS CERCANO
CUUACAN, SIN
Av. Nicolb,s Bravo #1063 Sur - Col. industrial Bravo (667) 7 12 42 11
GUADALAJARA, JAL
Av. La Paz #1779 - Col. Americana Sector Juarez (33) 3825 6978
MEXICO, D.E
Eje Central Lb,zaro Cardenas No. 18 (55) 5588 9377
Local D, Col. Obrera
MERIDA, YUC
Calie 63 #459-A - Col. Centro (999) 928 5038
MONTERREY, N.L.
Av. Francisco J.Madero No.831 - Col. Centro (81) 8375 2313
PUEBLA, PUE
17 Notre #205 - Col. Centro (222) 246 3714
QUERETARO, QRO
Av. Madero 139 Pte.- Col. Centro (442) 214 1660
SAN LUIS POTOSI, SLP
Av. Universidad 1525 - Col. San Luis (444) 814 2383
TORREON, COAH
Blvd. Jndependencia, 96 Pte. - Col. Centro (871) 716 5265
VERACRUZ, VER
Prolongaci6n Diaz Mir6n #4280 - Col. Remes (229) 921 7016
VlLLAHERMOSA, TAB
Constituci6n 516-A - Col. Centro (993) 312 5111
PARA OTRAS LOCAUDADES LLAME AL: (55) 5326 7100
Epecificaciones (DW896)
Tensi6n de alimentaci6n 120 V CA/CD
Potencia nominal: 380 W
Frecuencia de operaci6n: 60 Hz
Consumo de corriente: 3,0 A
IMPORTADOR: DEWALT S.A. DE C.V.
BOSQUES DE CIDROS ACCESO RADIATAS NO. 42
COL. BOSQUES DE LAS LOMAS, 3A. SECCION, CP 05120
DELEGACION CUAJIMALPA, MEXICO, D.F
TEL. 5 326 7100
R.F.C.: BDE810626-1W7
Para servicioy ventas consulte /..... ',,,
"HERRAMIENTAS ELECTRICAS" SECCJ_'
en lasecci6n arnarilla. AMARILLA
17
DEWALTIndustrialToolCo.,701 EastJoppa Road, Baltimore,MD 21286 (APR04) Form No. 384263-00 DW896
Copyright © 1997, 2004
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the "D" shaped air intake grill; the array of
pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

DeWalt DW896 TYPE 1 Owner's manual

Category
Power tools
Type
Owner's manual
This manual is also suitable for

DeWalt DW896 TYPE 1 is a 16-Gauge Nibbler designed to cut metal sheets with precision and ease. Its powerful motor and durable construction make it suitable for various metalworking applications, including HVAC, roofing, and fabrication. The tool features a versatile cutter that can be adjusted to cut in any direction, allowing for intricate cuts and shapes. With its compact size and lightweight design, the DW896 is easy to maneuver and control, even in tight spaces.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI