Kidde 21006371 User manual

Brand: Kidde

Model: 21006371

Category: Smoke detectors

Type: User manual

This manual is also suitable for

For your convenience, write down the following

information. If you call our Consumer Hotline,

these are the first questions you will be asked.

Smoke Alarm Model Number

(located on back of alarm):

Date Code (located on back of alarm).

National Fire Protection Association

(NFPA) and the manufacturer

recommends replacing this alarm

ten years from the date code:

Date of Purchase:

Where Purchased:

AC Wire-in Single and/or Multiple Station (up to 24 Devices)

Photoelectric Smoke Alarm with 9 Volt Battery Back Up and

“HUSH” Control to temporarily silence nuisance alarms.

Thank you for purchasing this smoke alarm. It is an important

part of your family’s home safety plan. You can trust this product

to provide the highest quality safety protection. We know you

expect nothing less when the lives of your family are at stake.

Kidde alarms and accessories CAN ONLY BE interconnected with

other Kidde alarms and accessories as well as specified brands and

models of interconnect compatible alarms. Connection of Kidde

products to a non-specified manufacturer’s interconnect system,

or connection with non-specified equipment from another manu-

facturer into an existing Kidde system could result in nuisance

alarming, failure to alarm, or damage to one or all of the devices

in the interconnect system. Refer to the User’s Guide supplied with

each Kidde product for interconnect compatible models, brands,

and devices. Refer to the wiring instructions in section 3 for NFPA

initiating device limits.

Smoke Alarm User’s Guide

21008164-EN Rev A

1375-7213-00

P12040

For model: P12040

SIGNALING

LISTED

WARNING! BATTERY DOOR WILL NOT CLOSE UNLESS A

BATTERY IS PRESENT. REMOVAL OF THE SMOKE ALARM

BATTERY AND DISCONNECTING OR LOSS OF AC POWER

WILL RENDER THE SMOKE ALARM INOPERATIVE.

ELECTRICAL RATING: 120 VAC, 60HZ, 80mA maximum per alarm

(maximum 80mA for originating unit with 24 devices interconnected).

CONTENTS OF THIS MANUAL

1 -- RECOMMENDED LOCATIONS FOR SMOKE ALARMS

2 -- LOCATIONS TO AVOID

3 -- INSTALLATION INSTRUCTIONS

4 -- OPERATION AND TESTING

5 -- NUISANCE ALARMS

6 -- MAINTENANCE

7 -- LIMITATIONS OF SMOKE ALARMS

8 -- GOOD SAFETY HABITS

9 -- NFPA PROTECTION STANDARD 72

10 --

CALIFORNIA STATE FIRE MARSHAL REQUIRED INFORMATION

11 -- SERVICE AND WARRANTY

1. RECOMMENDED LOCATIONS FOR ALARMS

• Locate the first alarm in the immediate area of the bedrooms.

Try to monitor the exit path as the bedrooms are usually farthest

from the exit. If more than one sleeping area exists, locate addi-

tional alarms in each sleeping area.

• Locate additional alarms to monitor any stairway as stairways act

like chimneys for smoke and heat.

• Locate at least one alarm on every floor level.

• Locate an alarm in every bedroom.

• Locate an alarm in every room where electrical appliances are

operated (i.e. portable heaters or humidifiers).

• Locate an alarm in every room where someone sleeps with the

door closed. The closed door may prevent an alarm not located

in that room from waking the sleeper.

• Smoke, heat, and combustion products rise to the ceiling and

spread horizontally. Mounting the smoke alarm on the ceiling in

the center of the room places it closest to all points in the room.

Ceiling mounting is preferred in ordinary residential construction.

• For mobile home installation, select locations carefully to avoid

thermal barriers that may form at the ceiling. For more details,

see MOBILE HOME INSTALLATION below.

• When mounting an alarm on the ceiling, locate it at a minimum

of 4” (10cm) from the side wall (see figure 1).

• When mounting the alarm on the wall, use an inside wall with

the top edge of the alarm at a minimum of 4” (10cm) and a

maximum of 12” (30.5cm) below the ceiling (see figure 1).

• Put smoke alarms at both ends of a bedroom hallway or large

room if the hallway or room is more than 30 ft (9.1 m) long.

• Install Smoke Alarms on sloped, peaked or cathedral ceilings

at or within 3 ft (0.9m) of the highest point (measured hori-

zontally). NFPA 72 states: “Smoke alarms in rooms with ceiling

slopes greater than 1 ft in 8 ft (.3m in 2.4m) horizontally shall

be located on the high side of the room.” NFPA 72 states: “A

row of alarms shall be spaced and located within 3 ft (0.9m) of

the peak of the ceiling measured horizontally” (see figure 3).

MOBILE HOME INSTALLATION

Modern mobile homes have been designed and built to be energy

efficient. Install smoke alarms as recommended above (refer to

RECOMMENDED LOCATIONS and figures 1 and 2).

FIGURE 2

FIGURE 3

FIGURE 1

In older mobile homes that are not well insulated compared to pres-

ent standards, extreme heat or cold can be transferred from the

outside to the inside through poorly insulated walls and roof. This

may create a thermal barrier which can prevent the smoke from

reaching an alarm mounted on the ceiling. In such units, install the

smoke alarm on an inside wall with the top edge of the alarm at a

minimum of 4” (10cm) and a maximum of 12” (30.5cm) below the

ceiling (see figure 1).

If you are not sure about the insulation in your mobile home, or if

you notice that the outer walls and ceiling are either hot or cold,

install the alarm on an inside wall. For minimum protection, install

at least one alarm close to the bedrooms. For additional protection,

see SINGLE FLOOR PLAN in figure 2.

WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER RV

OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE

EACH TRIP AND AT LEAST ONCE A WEEK DURING USE.

2. LOCATIONS TO AVOID

• In the garage. Products of combustion are present when you

start your automobile.

• Less than 4” (10cm) from the peak of an “A” frame type ceiling.

• In an area where the temperature may fall below 40ºF or rise

above 100ºF, such as garages and unfinished attics.

• In dusty areas. Dust particles may cause nuisance alarm or failure

to alarm.

• In very humid areas (greater than 85% R.H.). Moisture or steam

can cause nuisance alarms.

• In insect-infested areas.

• Smoke alarms should not be installed within 3 ft (.9m) of the fol-

lowing: the door to a kitchen, the door to a bathroom containing

a tub or shower, forced air supply ducts used for heating or cool-

ing, ceiling or whole house ventilating fans, or other high air flow

areas.

• Kitchens. Normal cooking may cause nuisance alarms. If a kitchen

alarm is desired, it should have an alarm silence feature or be a

photoelectric type.

• Near fluorescent lights. Electronic “noise” may cause nuisance

alarms.

• Smoke alarms are not to be used with detector guards unless the

combination (alarm and guard) has been evaluated and found

suitable for that purpose.

3. INSTALLATION INSTRUCTIONS

WIRING REQUIREMENTS

• This smoke alarm should be installed on a U.L. listed or recognized

junction box. All connections should be made by a qualified elec-

trician and all wiring used shall be in accordance with articles 210

and 300.3(B) of the U.S. National Electrical Code ANSI/NFPA 70,

NFPA 72 and/or any other codes having jurisdiction in your area.

The multiple station interconnect wiring to the alarms must be run

in the same raceway or cable as the AC power wiring. In addition,

the resistance of the interconnect wiring shall be a maximum of

10 ohms.

• The appropriate power source is 120 Volt AC Single Phase sup-

plied from a non-switchable circuit which is not protected by a

ground fault interrupter.

• WARNING: This alarm cannot be operated from power derived

from a square wave, modified square wave or modified sine wave

inverters. These types of inverters are sometimes used to supply

power to the structure in off grid installations, such as solar or

wind derived power sources. These power sources produce high

peak voltages that will damage the alarm.

WIRING INSTRUCTIONS FOR AC QUICK CONNECT HARNESS

CAUTION! TURN OFF THE MAIN POWER TO THE CIRCUIT

BEFORE WIRING THE ALARM.

• For alarms that are used as single station, DO NOT CONNECT THE

RED WIRE TO ANYTHING. Leave the red wire insulating cap in

place to make certain that the red wire cannot contact any metal

parts or the electrical box.

• When alarms are interconnected, all interconnected units must be

powered from a single circuit.

• A maximum of 24 Kidde devices may be interconnected in a mul-

tiple station arrangement. The interconnect system should not

exceed the NFPA interconnect limit of 12 smoke alarms and/or 18

alarms total (smoke, heat, carbon monoxide, etc.). With 18 alarms

interconnected, it is still possible to interconnect up to a total of 6

remote signaling devices and/or relay modules.

• When mixing models which have battery backup (i12040, i12040A,

i12060, i12060A, i12080, i12080A, i12090A, i4618, i1418A, 1275,

1276, 1285, 1296, PE120, P12040, PI2000, PI2010, KN-COSM-

IB, RF-SM-ACDC, KN-COPE-I, KN-SMFM-I, HD135F, KN-COB-IC,

KN-COP-IC) with models without battery backup, (i1235, i12020,

i12020A, KN-COSM-I SM120X, CO120X, SL177I) be advised that

the models without battery backup will not respond during an AC

power failure.

• The maximum wire run distance between the first and last unit in

an interconnected system is 1000 feet.

• Figure 4 illustrates interconnection wiring. Improper connection

will result in damage to the alarm, failure to operate, or a shock

hazard.

• Make certain alarms are wired to a continuous (non-switched)

power line. NOTE: Use standard UL listed household wire (as

required by local codes) available at all electrical supply stores and

most hardware stores.

FIGURE 4 INTERCONNECT WIRING DIAGRAM

WIRES ON ALARM HARNESS CONNECTED TO

Black Hot Side of AC Line

White Neutral Side of AC Line

Red Interconnect Lines (Red Wires) of

Other Units in the Multiple

Station Set up

BATTERY INSTALLATION

See Maintenance (section 6) for battery installation

CAUTION! IF BATTERY REMINDER FINGER IS NOT HELD DOWN

IN THE BATTERY COMPARTMENT BY THE BATTERY, THE

BATTERY DOOR WILL NOT CLOSE, THE AC QUICK CONNECTOR

WILL NOT ATTACH TO THE ALARM, AND THE ALARM WILL NOT

ATTACH TO THE TRIM RING (SEE SECTION 6, FIGURE 9).

FUSE

CIRCUIT

BREAKER

RED BLACK

WHITE

BLACK

WHITE

RED

CONNECTOR

Kidde

Relay Module

SM120X

First

Alarm

Additional

Alarm

Optional

Accessory

Additional

Alarm

MOUNTING INSTRUCTIONS

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!

1. Remove the trim ring from the back of the alarm by holding the

trim ring and twisting the alarm in the direction indicated by the

“OFF” arrow on the alarm cover.

2. After selecting the proper smoke alarm location as described

in section 1 and wiring the AC QUICK CONNECT harness as

described in the WIRING INSTRUCTIONS, attach the trim ring to

the electrical box (see figure 5).

3. Use a screwdriver to punch out only the pair of holes in the trim

ring that match your type of electrical box or plaster ring. Mount

the trim ring to the electrical box, using the appropriate holes.

NOTE: Use the circle, square and octagon markings near each

mounting hole in the trim ring to help you select the correct

mounting holes (see figure 5).

4. Pull the AC QUICK CONNECTOR through the center hole in the

trim ring and mount the ring, making sure that the mounting

screws are positioned in the small ends of the keyholes before

tightening the screws (see figure 5).

5. Plug the AC QUICK CONNECTOR into the back of the alarm (see

figure 6), making sure that the locks on the connector snap into

place. Then push the excess wire back into the electrical box

through the hole in the center of the trim ring.

6. If you have finished all the WIRING, BATTERY INSTALLATION AND

TRIM RING MOUNTING STEPS, you can install the alarm on the

trim ring. Alignment marks are provided on the side of the alarm

and on the trim ring (see figure 7).

7. Install the alarm on the trim ring with the indicating marks

aligned and rotate the alarm in the direction of the “ON” arrow

on the cover until the alarm snaps in place (see figure 7).

8. Turn on the AC power. The green AC Power On Indicator should

be lit when the alarm is operating from AC power.

FIGURE 5 SELECT CORRECT MOUNTING HOLES ON TRIM RING

Rectangular

Plaster Ring

Circular

Plaster Ring

Octagonal

Electrical Box

TAMPER RESIST LOCKING PIN: To make your smoke alarm tamper

resistant, a locking pin has been provided with your alarm. Using

this pin will help deter children and others from removing the

alarm from trim ring. To use the pin, insert it into the hole in the

side of the alarm after the alarm has been installed on the trim

ring (see figure 8). NOTE: The tamper resist pin will have to be

removed in order to change the batteries. Use long nose pliers to

pull the pin out of the hole. It is now possible to remove the alarm

from the trim ring.

After installation, TEST your alarm by pressing and holding the test

button for several seconds. This should sound the alarm.

4. OPERATION AND TESTING

OPERATION: The smoke alarm is operating once a fresh battery is

installed and testing is complete. When products of combustion

are sensed, the unit sounds a loud 85db pulsating alarm until the

air is cleared.

HUSH CONTROL: The “HUSH” feature has the capability of

temporarily desensitizing the alarm circuit for approximately 10

minutes. This feature is to be used only when a known alarm

condition, such as smoke from cooking activates the alarm. The

smoke alarm is desensitized by pushing the “HUSH” button on the

smoke alarm cover. If the smoke is not too dense, the alarm will

silence immediately and the red LED will flash every 10 seconds

for approximately 10 minutes. This indicates that the alarm is in a

temporarily desensitized condition. The smoke alarm will automati-

cally reset after approximately 10 minutes, and sound the alarm if

smoke is still present. The “HUSH” feature can be used repeatedly

until the air has been cleared of the condition causing the alarm.

NOTE: DENSE SMOKE WILL OVERRIDE THE HUSH CONTROL

FEATURE AND SOUND A CONTINUOUS ALARM.

To remove AC

connector,

squeeze

locking

arms and

pull.

Tamper resistant

locking pin

Alignment Marks

Remove

Install

FIGURE 6 FIGURE 7 FIGURE 8

CAUTION: BEFORE USING THE ALARM HUSH FEATURE,

IDENTIFY THE SOURCE OF THE SMOKE AND BE CERTAIN

A SAFE CONDITION EXISTS.

LED INDICATORS: This smoke alarm is equipped with red and green

LED indicators. The red LED is located under the test button and has

two modes of operation.

Standby Condition: The red LED will flash every 30-40

seconds to indicate that the smoke

alarm is operating properly.

Alarm Condition: When the alarm senses products of

combustion and goes into alarm, the red

LED will flash rapidly (one flash per second).

The rapid flashing LED and pulsating alarm

will continue until the air is cleared.

Hush Condition: The red LED will flash every 10 seconds

as long as the alarm is in Hush mode.

SMOKE SENSING CHAMBER OPERATION: This alarm will “chirp” if

any of the components in the smoke sensing chamber fail. This chirp

will occur between the flashes of the red LED indicator light. (If the

chirp occurs at the same time as the red LED flash, see section 6 for

low battery information).

WHEN UNITS ARE INTERCONNECTED, only the red LED of the alarm

which senses the smoke or is being tested (the originating unit) will

flash rapidly. All other units in the interconnect system will sound an

alarm but their red LED’s will NOT flash rapidly.

The green LED will be steady on to indicate the presence of AC power.

TESTING: Test by pushing the test button on the cover and holding it

down for a minimum of 5 seconds. This will sound the alarm if the

electronic circuitry, horn, and battery are working. In an intercon-

nected installation all interconnected alarms should sound when the

test button on any one of the interconnected alarm is pressed. If no

alarm sounds, check the fuse or circuit breaker supplying power to

the alarm circuit. Verify the green LED is on. If the alarm still does

not sound, the unit has defective batteries or other failure. DO NOT

use an open flame to test your alarm, you could damage the alarm

or ignite combustible materials and start a structure fire.

TEST THE ALARM WEEKLY TO ENSURE PROPER OPERATION. Erratic

or low sound coming from your alarm may indicate a defective

alarm, and it should be returned for service (see section 12).

NOTE: WEEKLY TESTING IS REQUIRED.

5. NUISANCE ALARMS

Smoke alarms are designed to minimize nuisance alarms.

Cigarette smoke will not normally set off the alarm, unless the

smoke is blown directly into the alarm. Combustion particles from

cooking may set off the alarm if the alarm is located close to the

cooking area. Large quantities of combustible particles are gener-

ated from spills or when broiling. Using the fan on a range hood

which vents to the outside (non-recirculating type) will also help

remove these combustible products from the kitchen.

If the alarm does sound, check for fires first. If a fire is discovered,

get out and call the fire department. If no fire is present, check

to see if one of the reasons listed in section 2 may have caused

the alarm. The Model P12040 has a “HUSH” control that is

extremely useful in a kitchen area or other areas prone to nuisance

alarms. For more information refer to section 4, OPERATION AND

TESTING.

6. MAINTENANCE

IF TAMPER RESIST PIN HAS BEEN USED, REFER TO TAMPER

RESIST LOCKING PIN IN SECTION 3 FOR PIN REMOVAL

INSTRUCTIONS.

To replace the battery, remove the alarm from the trim ring by

rotating the alarm in the direction of the “OFF” arrow on the

cover (see Section 3, Figure 7) To disconnect the A.C. power

harness, squeeze the locking arms on the sides of the Quick con-

nector while pulling the connector away from the bottom of the

alarm (see Section 3, Figure 6).

BATTERY INSTALLATION AND REMOVAL

To replace or install the batteries, you must first remove the alarm

from the trim ring by following the ALARM REMOVAL instructions

at the beginning of this section. After alarm has been removed,

you can open the battery door and install or replace the battery.

Battery installation instructions are provided on the inside of the

battery door.

FIGURE 9

When installing the battery, press the battery reminder finger

down into the battery compartment and install the battery (see

Figure 9).

CAUTION! IF THE BATTERY REMINDER FINGER IS NOT HELD

DOWN IN THE BATTERY COMPARTMENT BY THE BATTERY,

THE BATTERY DOOR WILL NOT CLOSE, THE A.C. QUICK

CONNECTOR WILL NOT ATTACH TO THE ALARM, AND THE

ALARM WILL NOT ATTACH TO THE TRIM RING.

The Model P12040 Smoke Alarm uses a 9V backup battery

(Carbon zinc, alkaline and lithium batteries may be used). A fresh

battery should last for one year under normal operating condi-

tions. This alarm has a low battery monitor circuit which will

cause the alarm to “chirp” approximately every 30 - 40 seconds

for a minimum of seven (7) days when the battery gets low.

Replace the battery when this condition occurs.

USE ONLY THE FOLLOWING 9 VOLT BATTERIES FOR SMOKE

ALARM REPLACEMENT.

Carbon Zinc Type: EVEREADY 1222;

GOLD PEAK 1604P OR 1604S

Alkaline Type: ENERGIZER 522; DURACELL MN1604,

MX1604,GOLD PEAK 1604A

PANASONIC 6AM6, 6AM-6, 6AM-6PI,

6AM6X, and 6LR61(GA)

Lithium Type: ULTRALIFE U9VL-J

NOTE: WEEKLY TESTING IS REQUIRED.

WARNING!! USE ONLY THE BATTERIES SPECIFIED. USE OF

DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT

ON THE SMOKE ALARM.

CLEANING YOUR ALARM

YOUR ALARM SHOULD BE CLEANED AT LEAST ONCE A YEAR

To clean your alarm, remove it from the mounting bracket as out-

lined in the beginning of this section. You can clean the interior

of your alarm (sensing chamber) by using compressed air or a vac-

uum cleaner hose and blowing or vacuuming through the open-

ings around the perimeter of the alarm. The outside of the alarm

can be wiped with a damp cloth. If cleaning does not restore the

alarm to normal operation the alarm should be replaced.

After cleaning, reinstall your alarm. Test your alarm by using the

test button and check that the green LED is on.

7. LIMITATIONS OF SMOKE ALARMS

WARNING: PLEASE READ CAREFULLY AND THOROUGHLY

• NFPA 72 states: Life safety from fire in residential occupancies

is based primarily on early notification to occupants of the need

to escape, followed by the appropriate egress actions by those

occupants. Fire warning systems for dwelling units are capable

of protecting about half of the occupants in potentially fatal

fires. Victims are often intimate with the fire, too old or young,

or physically or mentally impaired such that they cannot escape

even when warned early enough that escape should be possible.

For these people, other strategies such as protection-in-place or

assisted escape or rescue are necessary.

• Smoke alarms are devices that can provide early warning of pos-

sible fires at a reasonable cost; however, alarms have sensing

limitations. Ionization sensing alarms may detect invisible fire

particles (associated with fast flaming fires) sooner than photo-

electric alarms. Photoelectric sensing alarms may detect visible

fire particles (associated with slow smoldering fires) sooner than

ionization alarms. Home fires develop in different ways and are

often unpredictable. For maximum protection, Kidde recom-

mends that both Ionization and Photoelectric alarms be installed.

• A battery powered alarm must have a battery of the specified type,

in good condition and installed properly.

• AC powered alarms (without battery backup) will not operate if

the AC power has been cut off, such as by an electrical fire or

an open fuse.

• Smoke alarms must be tested regularly to make sure the batter-

ies and the alarm circuits are in good operating condition.

• Smoke alarms cannot provide an alarm if smoke does not reach

the alarm. Therefore, smoke alarms may not sense fires starting

in chimneys, walls, on roofs, on the other side of a closed door

or on a different floor.

• If the alarm is located outside the bedroom or on a different

floor, it may not wake up a sound sleeper.

• The use of alcohol or drugs may also impair one’s ability to hear

the smoke alarm. For maximum protection, a smoke alarm

should be installed in each sleeping area on every level of a

home.

• Although smoke alarms can help save lives by providing an early

warning of a fire, they are not a substitute for an insurance

policy. Home owners and renters should have adequate insur-

ance to protect their lives and property.

8. GOOD SAFETY HABITS

DEVELOP AND PRACTICE A PLAN OF ESCAPE

• Install and maintain fire extinguishers on every level of the home

and in the kitchen, basement and garage. Know how to use a

fire extinguisher prior to an emergency.

• Make a floor plan indicating all doors and windows and at least

two (2) escape routes from each room. Second story windows

may need a rope or chain ladder.

• Have a family meeting and discuss your escape plan, showing

everyone what to do in case of fire.

• Determine a place outside your home where you all can meet

if a fire occurs.

• Familiarize everyone with the sound of the smoke alarm and

train them to leave your home when they hear it.

• Practice a fire drill at least every six months, including fire drills

at night. Ensure that small children hear the alarm and wake

when it sounds. They must wake up in order to execute the

escape plan. Practice allows all occupants to test your plan

before an emergency. You may not be able to reach your chil-

dren. It is important they know what to do.

• Current studies have shown smoke alarms may not awaken all

sleeping individuals, and that it is the responsibility of individuals

in the household that are capable of assisting others to provide

assistance to those who may not be awakened by the alarm

sound, or to those who may be incapable of safely evacuating

the area unassisted.

WHAT TO DO WHEN THE ALARM SOUNDS

• Alert small children in the home.

• Leave immediately by your escape plan. Every second counts,

so don’t waste time getting dressed or picking up valuables.

• In leaving, don’t open any inside door without first feeling its

surface. If hot, or if you see smoke seeping through cracks,

don’t open that door! Instead, use your alternate exit. If the

inside of the door is cool, place your shoulder against it, open it

slightly and be ready to slam it shut if heat and smoke rush in.

• Stay close to the floor if the air is smoky. Breathe shallowly

through a cloth, wet if possible.

• Once outside, go to your selected meeting place and make

sure everyone is there.

• Call the fire department from your neighbor’s home -

not from yours!

• Don’t return to your home until the fire officials say that

it is all right to do so.

There are situations where a smoke alarm may not be effective

to protect against fire as stated in the NFPA Standard 72.

For instance:

a) smoking in bed

b) leaving children home alone

c) cleaning with flammable liquids, such as gasoline

9. NFPA REQUIRED PROTECTION

The National Fire Protection Association’s Standard 72 provides

the following information:

Smoke Detection - Where required by applicable laws, codes,

or standards for the specified occupancy, approved single- and

multiple-station smoke alarms shall be installed as follows: (1) In

all sleeping rooms Exception: Smoke alarms shall not be required

in sleeping rooms in existing one- and two-family dwelling units.

(2) Outside of each separate sleeping area, in immediate vicinity of

the sleeping rooms. (3) On each level of the dwelling unit, includ-

ing basements Exception: In existing one- and two-family dwelling

units, approved smoke alarms powered by batteries are permitted.

Smoke Detection - Are More Smoke Alarms Desirable? The

required number of smoke alarms might not provide reliable early

warning protection for those areas separated by a door from the

areas protected by the required smoke alarms. For this reason, it

is recommended that the householder consider the use of addi-

tional smoke alarms for those areas for increased protection. The

additional areas include the basement, bedrooms, dining room,

furnace room, utility room, and hallways not protected by the

required smoke alarms. The installation of the smoke alarms in

the kitchen, attic (finished or unfinished), or garage is normally

not recommended, as these locations occasionally experience

conditions that can result in improper operation.

This equipment should be installed in accordance with the

National Fire Protection Association’s Standard 72 (NFPA,

Batterymarch Park, Quincy, MA 02269).

NOTIFY YOUR LOCAL FIRE DEPARTMENT AND INSURANCE

COMPANY OF YOUR SMOKE ALARM INSTALLATION.

10. CAUTION (AS REQUIRED BY THE CALIFORNIA

STATE FIRE MARSHAL)

“Early warning fire detection is best achieved by the installation

of fire detection equipment in all rooms and areas of the house-

hold as follows. A smoke alarm installed in each separate sleeping

area (in the vicinity of, but outside of the bedrooms), and heat or

smoke alarms in the living rooms, dining rooms, bedrooms, kitch-

ens, hallways, attics, furnace rooms, closets, utility and storage

rooms, basements and attached garages”.

11. SERVICE AND WARRANTY

If after reviewing this manual you feel that your smoke alarm is

defective in any way, do not tamper with the unit. Return it for

servicing to: Kidde, 1016 Corporate Park Dr., Mebane, NC 27302.

1-800-880-6788 (See Warranty for in-warranty returns).

TEN YEAR LIMITED WARRANTY

Kidde warrants to the original purchaser that the enclosed smoke alarm

(but not the battery) will be free from defects in material and workman-

ship or design under normal use and service for a period of ten years

from the date of purchase. The obligation of Kidde under this warranty

is limited to repairing or replacing the smoke alarm or any part which we

find to be defective in material, workmanship or design, free of charge

to the customer, upon sending the smoke alarm with proof of date

of purchase, postage and return postage prepaid, to Warranty Service

Department, Kidde, 1016 Corporate Park Dr., Mebane, NC 27302.

This warranty shall not apply to the smoke alarm if it has been damaged,

modified, abused or altered after the date of purchase or if it fails to

operate due to improper maintenance or inadequate AC or DC electrical

power.

THE LIABILITY OF KIDDE OR ANY OF ITS PARENT OR SUBSIDIARY

CORPORATIONS ARISING FROM THE SALE OF THIS SMOKE ALARM OR

UNDER THE TERMS OF THIS LIMITED WARRANTY SHALL NOT IN ANY

CASE EXCEED THE COST OF REPLACEMENT OF SMOKE ALARM AND,

IN NO CASE, SHALL KIDDE OR ANY OF ITS PARENT OR SUBSIDIARY

CORPORATIONS BE LIABLE FOR CONSEQUENTIAL LOSS OR DAMAGES

RESULTING FROM THE FAILURE OF THE SMOKE ALARM OR FOR BREACH

OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE

LOSS OR DAMAGE IS CAUSED BY THE COMPANY’S NEGLIGENCE OR

FAULT.

Since some states do not allow limitations on the duration of an implied

warranty or do not allow the exclusion or limitation of incidental or

consequential damages, the above limitations or exclusions may not

apply to you. While this warranty gives you specific legal rights, you

may also have other rights which vary from state to state.

Also, Kidde makes no warranty, express or implied, written or oral,

including that of merchantability or fitness for any particular purpose,

with respect to the battery.

The above warranty may not be altered except in writing signed by

both parties hereto.

QUESTIONS OR FOR MORE INFORMATION

Call our Consumer Hotline at 1-800-880-6788 or contact

us at our website at www.kidde.com

Kidde, 1016 Corporate Park Drive, Mebane, NC 27302

Kidde 21006371 User manual

Brand: Kidde

Model: 21006371

Category: Smoke detectors

Type: User manual

This manual is also suitable for

Download PDF

report

Kidde 21006371 User manual

This manual is also suitable for

Kidde 21006371 User manual

Related papers

Other documents