Storm System 412C168-5 Installation guide

Type
Installation guide
Product Description:
This heavily pigmented acrylic latex matte finish stain is ideal for use on new or previously stained exterior woods. The
durable light fast pigments provide maximum fade resistance and color retention. This product is self-priming over
most substrates where extractive bleeding is not a concern. Solid Color Latex Stains are extremely high-hiding and
provide maximum stain durability while enhancing the natural grain and texture of the wood. Solid color stain is water
repellent, mildew and fungus resistant and long lasting.
Storm System Acrylic Matte Stain can be used over previously painted sealed surfaces, hardboard siding or smooth
planed cedar clapboards; surfaces which are not recommended for Linseed Oil Stains. This product contains wood
preservatives which will help protect the film against mildew, fungus, and moisture on a properly prepared surface. Not
for use on horizontal surfaces.
Precautions:
Remove all mildew before application with Storm System Mold and Mildew Stain Remover. Not recommended for
interior use. Avoid applying light color stains over dark stains or over creosote base stains. Air and surface
temperature must be 35° F during application and drying time. Do not apply to smooth side clapboards without
thorough sanding, weathering or pressure washing. Not recommended for decks or horizontal surfaces.
Architectural Specifications:
▪ UNFINISHED SHINGLES, SHAKES, CLAPBOARDS, TEXTURE BOARD, TRIM
1 coat of 523XX Quick Dry Oil Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ HARDBOARD SIDING, SMOOTH BOARD (or shakes, shingles or clapboards where extractive bleeding may occur)
1 coat Storm System Quick Dry Oil Primer No. 52344 or Storm System Acrylic Latex Primer w/ Troubleshooter®
Technology No. 54300 + 1 coat of 523XX Quick Dry Oil Primer
1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ PREVIOUSLY STAINED SURFACES
1 coat of 523XX (Oil) or 543XX (Latex) Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ PREVIOUSLY PAINTED OR SEALED SURFACES
1 coat of 523XX (Oil) or 543XX (Latex) Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
Application:
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect
yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lead.
Surface Preparation:
Surfaces must be thoroughly clean and dry. Always test a small area before application to the entire surface. All
mildewed areas should be cleaned with Storm System All Surface Mold & Mildew Stain Remover. New pressure
treated wood should be scrubbed with Storm System All Surface Cleaner to remove all surface deposits. Rinse
thoroughly and allow to dry.
New wood should be primed with Storm System Oil or Latex Wood Primer before applying white or light colors to avoid
bleeding and discoloration from water soluble wood extracts.This material can be applied by synthetic, bristle brush,
roller, pad applicator or spray gun. Stain only a few rows of siding or shingles at one time. Always start from the top
and work across towards a natural break or edge such as a window or door. On vertical siding, start a few boards at
the top and go all the way to the bottom. Avoid overlapping.
On hot summer days, a small amount of water can be added to this product to maintain a wet edge. Apply stain on the
shady side of a building and not in direct sun whenever possible. These hot weather limitations do not apply to spray
applications. This product is self-priming on new wood. New or unfinished wood to be stained with Storm System
White or other light colors, however, should be primed with Storm System Quick Dry Oil Primer No. 52344 or Storm
System Acrylic Latex Primer w/ Troubleshooter® Technology No. 54300 to avoid natural tannin or sugar bleed through
from the new wood.
Recommended Use:
Shingles, Trim, Shakes, Fences, Clapboards, Plywood, Texture Board, Hardboard, Outdoor Furniture
Safety Information:
Keep out of reach of children. Do not take internally. Close container after each use.
100% Acrylic Stain - Matte
412 Series
4/10/2017
STORM SYSTEM™
California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141
5/16/2013
Exterior
Type:
Acrylic Latex*
2
Volume Solids:
26.9
@ 60°
%
Solids by Weight:
42.8
%
Dry Film Thickness:
1.3
mils
Vehicle:
69.3
%
Pigment:
30.7
%
Viscosity @ 77 °F:
92
KU
Maximum VOC:
150
g/liter
Flash Pt °F:
Non-combustible
Thinner:
Water
Product Specifications:
Exposure:
Exterior
(Weight Per Gallon:
10.7
Available Package Sizes:
To Handle:
6-8
To Recoat:
4
hrs.
hrs.
hrs.
To Touch:
1
Drying Times:
lbs. ± .5 lb)
Surface Spread Rate:
s.f./gal.
(Spray Application is 50% of above)
Tools and Equipment:
±
2
Smooth:
300-350
Porous:
225-275
s.f./gal.
Brush -
Synthetic, Nylon or Polyester
Roller -
3/8" Nap Synthetic Fiber
Airless Spray -
.017 to Tip
±2
±2
±2
±2
±5
(@ 70-77 °F, 50% R.H.)
Soap & Water
Clean Up:
Available Colors and Bases:
Gallon 5 Gallon
See back page
for complete list
ITEM # COLOR NAME
41200XX White
41291XX Light Base
41292XX Medium Base
41293XX Deep Base
41295XX Clear Base
412C155 Apache Tears
412C156 Birch Beer
412C158 Chestnut Brown
412C159 Chocolate Lab
412C160 Cubano Brown
412C161 Fawn
412C162 Grizzly Bear
412C163 Melted Chocolate
412C164 Moosehead Pine
412C165 Redwood
412C166 Rich Soil
412C167 Rusty Anchor
412C168 Southwest Sangria
412C169 Spilled Wine
412C170 Steel Rod
412D145 Gray Flannel Suit
412D146 Hollywood
412D147 Horse Trot
412D148 Joe's Moss
412D149 Lake Winnipesaukee
412D150 Lodestone
412D151 Mojave Desert
412D153 Steel Sea
412D154 Zion Forest
412L103 Bedrock
412L105 Country Club White
412L108 Ghost Plant
412L109 Granite State
Product Description:
This heavily pigmented acrylic latex matte finish stain is ideal for use on new or previously stained exterior woods. The
durable light fast pigments provide maximum fade resistance and color retention. This product is self-priming over
most substrates where extractive bleeding is not a concern. Solid Color Latex Stains are extremely high-hiding and
provide maximum stain durability while enhancing the natural grain and texture of the wood. Solid color stain is water
repellent, mildew and fungus resistant and long lasting.
Storm System Acrylic Matte Stain can be used over previously painted sealed surfaces, hardboard siding or smooth
planed cedar clapboards; surfaces which are not recommended for Linseed Oil Stains. This product contains wood
preservatives which will help protect the film against mildew, fungus, and moisture on a properly prepared surface. Not
for use on horizontal surfaces.
Precautions:
Remove all mildew before application with Storm System Mold and Mildew Stain Remover. Not recommended for
interior use. Avoid applying light color stains over dark stains or over creosote base stains. Air and surface
temperature must be 35° F during application and drying time. Do not apply to smooth side clapboards without
thorough sanding, weathering or pressure washing. Not recommended for decks or horizontal surfaces.
Architectural Specifications:
▪ UNFINISHED SHINGLES, SHAKES, CLAPBOARDS, TEXTURE BOARD, TRIM
1 coat of 523XX Quick Dry Oil Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ HARDBOARD SIDING, SMOOTH BOARD (or shakes, shingles or clapboards where extractive bleeding may occur)
1 coat Storm System Quick Dry Oil Primer No. 52344 or Storm System Acrylic Latex Primer w/ Troubleshooter®
Technology No. 54300 + 1 coat of 523XX Quick Dry Oil Primer
1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ PREVIOUSLY STAINED SURFACES
1 coat of 523XX (Oil) or 543XX (Latex) Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
▪ PREVIOUSLY PAINTED OR SEALED SURFACES
1 coat of 523XX (Oil) or 543XX (Latex) Primer + 1 or 2 coats Storm System 100% Acrylic Stain - Matte No. 412 Series
Application:
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect
yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lead.
Surface Preparation:
Surfaces must be thoroughly clean and dry. Always test a small area before application to the entire surface. All
mildewed areas should be cleaned with Storm System All Surface Mold & Mildew Stain Remover. New pressure
treated wood should be scrubbed with Storm System All Surface Cleaner to remove all surface deposits. Rinse
thoroughly and allow to dry.
New wood should be primed with Storm System Oil or Latex Wood Primer before applying white or light colors to avoid
bleeding and discoloration from water soluble wood extracts.This material can be applied by synthetic, bristle brush,
roller, pad applicator or spray gun. Stain only a few rows of siding or shingles at one time. Always start from the top
and work across towards a natural break or edge such as a window or door. On vertical siding, start a few boards at
the top and go all the way to the bottom. Avoid overlapping.
On hot summer days, a small amount of water can be added to this product to maintain a wet edge. Apply stain on the
shady side of a building and not in direct sun whenever possible. These hot weather limitations do not apply to spray
applications. This product is self-priming on new wood. New or unfinished wood to be stained with Storm System
White or other light colors, however, should be primed with Storm System Quick Dry Oil Primer No. 52344 or Storm
System Acrylic Latex Primer w/ Troubleshooter® Technology No. 54300 to avoid natural tannin or sugar bleed through
from the new wood.
Recommended Use:
Shingles, Trim, Shakes, Fences, Clapboards, Plywood, Texture Board, Hardboard, Outdoor Furniture
Safety Information:
Keep out of reach of children. Do not take internally. Close container after each use.
100% Acrylic Stain - Matte
412 Series
4/10/2017
STORM SYSTEM™
California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141
5/16/2013
Exterior
Type:
Acrylic Latex*
Specular Gloss:
2
Volume Solids:
26.9
@ 60°
%
Solids by Weight:
42.8
%
Dry Film Thickness:
1.3
mils
Vehicle:
69.3
%
Pigment:
30.7
%
Viscosity @ 77 °F:
92
KU
Maximum VOC:
150
g/liter
Flash Pt °F:
Non-combustible
Thinner:
Water
Product Specifications:
Exposure:
Exterior
(Weight Per Gallon:
10.7
Available Package Sizes:
To Handle:
6-8
To Recoat:
4
hrs.
hrs.
hrs.
To Touch:
1
Drying Times:
lbs. ± .5 lb)
Surface Spread Rate:
s.f./gal.
(Spray Application is 50% of above)
Tools and Equipment:
±
2
Smooth:
300-350
Porous:
225-275
s.f./gal.
Brush -
Synthetic, Nylon or Polyester
Roller -
3/8" Nap Synthetic Fiber
Airless Spray -
.017 to Tip
±2
±2
±2
±2
±5
(@ 70-77 °F, 50% R.H.)
Soap & Water
Clean Up:
Available Colors and Bases:
Gallon 5 Gallon
See back page
for complete list
ITEM # COLOR NAME
412L110 Hyannis Port
412L111 Lighthouse Fog
412L112 Max Blue
412L113 Mystic Dune
412L114 Mystic Gray
412L115 Natural Clay
412L117 Peaceful Garden
412L118 Phoebe
412L119 Pigeon Feather
412L120 Plimouth Plantation
412L121 Sand Castle
412L122 Sand Dollar Taupe
412L123 Sand Dune Fence
412L124 Sea Scallop
412L125 Seacoast Gray
412L126 Seashell
412L127 Sleeping Bear Dunes
412L128 Summer Mint
412L130 Vintage Pearl
412M131 Bar Harbor
412M132 Buckskin Jacket
412M133 California Stucco
412M134 English Tweed
412M135 Irish Tweed
412M136 Laguna Beach
412M137 Naked
412M138 Sand Storm
412M139 Santa Barbara
412M140 Squirrel Tail
412M141 Sunset Beige
412M142 Susan's Glow
412M143 Tiki Tan
412M144 Wet Sand
  • Page 1 1
  • Page 2 2

Storm System 412C168-5 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI