RAB Lighting TRLED2X2-50N/D10 Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
TRLED2X2-50N/D10
Type
Operating instructions

This manual is also suitable for

RAB Lighting TRLED2X2-50N/D10 is a high-quality lighting fixture designed for recessed ceiling mounting in both insulated and non-insulated ceilings. It features a 9/16" or 15/16" exposed Flat Tee Grid Ceiling and is suitable for Damp locations.

The fixture is easy to install and maintain, with a hinged door frame that can be removed if required. It also has grid clip screws that can be loosened from the inside of the housing for easy adjustment.

The TRLED2X2-50N/D10 uses 0-10V dimming, which allows for precise control of the light output. It has a universal voltage driver that permits operation at 120V through 277V, 50 or 60 Hz.

RAB Lighting TRLED2X2-50N/D10 is a high-quality lighting fixture designed for recessed ceiling mounting in both insulated and non-insulated ceilings. It features a 9/16" or 15/16" exposed Flat Tee Grid Ceiling and is suitable for Damp locations.

The fixture is easy to install and maintain, with a hinged door frame that can be removed if required. It also has grid clip screws that can be loosened from the inside of the housing for easy adjustment.

The TRLED2X2-50N/D10 uses 0-10V dimming, which allows for precise control of the light output. It has a universal voltage driver that permits operation at 120V through 277V, 50 or 60 Hz.

TRLED2X2 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
SAFETY INSTRUCTIONS
WARNING: Risk of re or electric shock. Suitable for Damp locations.
WARNING: Suitable for 9/16” or 15/16” Flat Tee Grid in both Insulated Ceilings and Non-Insulated Ceilings.
WARNING: Do not handle energized xture when hands are wet, when standing on wet or damp surfaces, or in water.
WARNING: Vapor barrier must be suitable for 90 ͦ C.
WARNING: Fixture to be independently supported to building structure.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture.
RECESSED CEILING MOUNTING
The xture is suitable only for INDOOR RECESSED CEILING
application.
To mount in an insulated or non-insulated ceiling - 9/16” or
15/16” exposed Flat Tee Grid Ceiling follow the steps below.
1. Pull the Latch (2) on Hinged Door Frame to swing
open the xture. Hinged Door Frame can be removed,
if required.
WARNING: Do not touch the LEDs.
2. Loosen Grid Clip Screws (4) from inside of Housing.
3. Rotate and slide the Housing as required to t through
the Tee-Grid Bar and place it as shown. Tighten Grid
Clip Screws (4) to secure the Housing.
4. Make sure that the orientation of the Access Plate faces
an accessible tile to make electrical splices.
5. Knock out appropriate conduit knockouts on the Access
Plate to route input conduit. Use appropriate conduit
connectors as required by code.
6. Connect wires as shown in wiring diagram.
WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sheet metal or other
sharp objects.
7. Support wires are required by Installation Codes. Bend
(4) Support Wire Hook upwards at Housing corners.
Support Housing to the building structure by Support
Wires (supplied by others) through the support wire
hook hole.
8. If removed, Hinged Door Frame can be hinged or
latched from either directon. Close the Hinged Door
Frame.
Housing
Tee-Grid
Bar
Access Plate
Support Wire
(supplied by
others)
3-3/8 ”
Grid Clip
Support Wire Hook
Latch
Latch
Hinged
Door
Frame
Grid Clip
(Pull Here)
(Bend Upwards)
Support
Wire
Hook
Grid Clip
Screw
Grid Clip
(Loosen from inside)
TRLED2X2 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean acrylic lens & xture with non-abrasive cleaning
solution.
2. Do not open xture to clean the LEDs. Do not touch the
LEDs.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Be sure the xture is grounded properly.
Fig. 1
010V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. 0-10V control wires must be rated for 300V
minimum. For 0-10V Dimming, follow the wiring directions as
in g. 1.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply ground.
Do NOT connect the GROUND of the dimming xture to
the output.
4. Connect the violet xture lead to the (V+) DIM lead.
5. Connect the gray xture lead to the (V-) DIM lead.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
TRLED2X2 IN-0314
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
  • Page 1 1
  • Page 2 2

RAB Lighting TRLED2X2-50N/D10 Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
TRLED2X2-50N/D10
Type
Operating instructions
This manual is also suitable for

RAB Lighting TRLED2X2-50N/D10 is a high-quality lighting fixture designed for recessed ceiling mounting in both insulated and non-insulated ceilings. It features a 9/16" or 15/16" exposed Flat Tee Grid Ceiling and is suitable for Damp locations.

The fixture is easy to install and maintain, with a hinged door frame that can be removed if required. It also has grid clip screws that can be loosened from the inside of the housing for easy adjustment.

The TRLED2X2-50N/D10 uses 0-10V dimming, which allows for precise control of the light output. It has a universal voltage driver that permits operation at 120V through 277V, 50 or 60 Hz.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents