Lightolier IS:40719 User manual

Brand: Lightolier

Model: IS:40719

Type: User manual

Lightolier IS:40719 is a radiance stem extension kit intended for installation in accordance with the National Electric Code and local regulations. Consult with your local electrical inspector before installation. To prevent electric shock, turn off electricity at the fuse box before proceeding. Retain these instructions for maintenance reference.

The kit includes a center stem assembly, extension stem, and swivel casting/crossbar assembly. It allows for the extension of the fixture's stem, providing additional height and flexibility in placement. The quick connectors at the lower end of the center stem assembly ensure easy and secure connection to the fixture wires.

READANDUNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTURE

lNSTRUCTION SHEET NO,

hisfktureisintendedfor installation in ectordanse with the National Eladricd Code end Id rsgulatbna,

o sssurs full sompfianca with Ixal OxJes snd rsgule.tkma,c+@ with your Ixd e!ectriral ins@or Lwfora

wtallation. To prevent eleotrfd sheck, turn off elacbiciy at fuss box before premsding.

IS:40719

Retsintheseinstructionsformaintenancereferenoe.

Pegelofl

INSTRUCTIONS FOR INSTALLATION

AND ASSEMBLY OF

RADIANCE STEM EXTENSION KITS

CAUTION:

BE CAREFUL WHILE HANDLING FIXTURE WIRES. DO NOT DAMAGE WIRE INSULATION

OR PINCH WIRES BETWEEN PARTS.

1. Unps& CENTER STEM ASSEMBLY (supplisd with f~re) snd cmefuliy until FIXTURE WIRES.

2. Gent~ pull downward en CANOPY to disengege fmm CROSSBAR SPRING CLIPS and expmw CROSSBAR (fig, 1),

3. Remove the two SCREWS from beth sides d SWIVEL CASTING snd skfe SWIVEL PIN oul fmm one d the holse in the SWIVEL CASTING (Fig, 1).

NOTE A small smswddver may be required to push SWIVEL

PINoutthroughtie hobinSWIVELCASTING,

CAUTION: PLACE SCREWS AND SWIVEL PIN IN A SAFE PLACE; THESE PARTS ARE NEEDED FOR FINAL

ASSEMBLY OF EXTENSION KIT.

4. While holding CENTER STEM ASSEMBLYsnd FIX7UREWIRES, genttfslikieSWlVELCASTlNGfCRQ3SsARAs3EMBLYup FIXTURE WIRES UnfiIA~EMBLY

ISmmpletely rsmoved fmm FIXTURE WIRES (Fig. 2), Plain SWIVEL CASTING/CROSSBAR ASSEMBLY ins safe place.

NOTE Make owtsin QUICK CONNECTORS at the lower

endofCENTERSTEMAS3EMSLYdonotslideupinsideSTEM,

FIXTUREWIRES

CROSSBAR

FIXTUREWIRES

(UN.COILED)

CROSSBAR

SWIVELCASTING

SPRINGCLIPS

ZSP’N

SWIVELCASTING[

CENTERSTEMASSEMBLY

SCREWS

CROSSBARASSEMBLY

[SUPPLIEDWITHFIXNREI

CENTERSTEM

CANOPY

ASSEMBLY

FIG,1

5. Pass FIXTURE WIRES through EXTENSION STEM COLIAR and EXTENSION STEM and slide EXTENSION STEM dewn FIXTURE WIRES until

EXTENSION STEM COL~R meets CENTER STEM AssEMSLY (Fig. 3A),

6. Aligning the holes in the side of CENTER STEM ASSEMBLY WW tie UWSSCIWh~l~ in EXTENSION STEM COLIAR, SIIW COMR to side in~~e

CENTER STEM ASSEMBLY and secure in place by installing the two screws providwJ whh EX7ENSION STEM KIT (fig, 3S),

NOTE Before preceedin~ repeat steps 5 snd 6 f a ssmnd EXTENSION STEM KIT is to b used,

7. Re.sssemble SWIVEL CASTING/CROSSBAR ASSEMSLY te the end of WENSION STEM by reveming steps 3 snd 4 above (Fig. 4),

8. Continue FIXTURE insfsllation by following instructions supplisd with FIXTURE,

NOTE FIXTURES are supplied with enough FIXTURE WIRE 10allow two EXTENSION STEM KITS to be insfsllsd. Ifonly one EXTENSION KIT is uset

excass FIXTURE WIRES should be cut off making certain Mere is a minimum of 6’ of FIXTURE WIRE sbeve CROSSBAR ASSEMSLY for OUTLET BOX WIRING,

‘:’: 4=-:s::

1.1<>

l-l-i-c>1.1E la”%R%,gwywu’

—

Lightolier IS:40719 User manual

Lightolier IS:40719 User manual

Lightolier IS:40719 User manual

Related papers

Other documents