Aeg-Electrolux HD6470-M User manual

Category
Cooker hoods
Type
User manual
64
Contents
Safety warnings 65
For the user 65
For the installer 66
Description of the appliance 68
Extraction 68
Recirculation 68
Control Panel - Model DM 8700 - DD 8770 69
Switching on the hood 70
Switching on the light 70
Control device for grease or charcoal filter 70
Led signal for grease filter 70
Led signal for charcoal filter 70
Re-setting the saturation signal 70
Control Panel - Model DM 8600 71
Control device for grease and charcoal filters 72
Grease filter LED (D) 72
Charcoal filter LED (E) 72
Resetting the saturation indicator 72
Control Panel - Model DM 8400 - HD 6470 73
Maintenance and care 74
Cleaning the hood 74
Metal grease filter 74
Removing the metal grease filter 74
Charcoal filter 75
Changing the light bulb 76
Special accessories 76
What to do if 77
Technical assistance service 78
Technical specifications 79
Mounting accessories included 79
Electrical connection 80
Safety warnings for the electrician 80
Wall unit mounting 81
Special accessories/Vapour screen 84
65
Safety warnings
For the user
The cooker hood is designed to extract unpleasant odours from the
kitchen, it will not extract steam.
Always cover lighted elements, to prevent excess heat from
damaging the appliance. In the case of oil, gas and coal fired
cookers it is essential to avoid open flames.
Also, when frying, keep the deep frying pan on the cooker top/cooker
under careful control.
The hot oil in the frying pan might ignite due to overheating.
The risk of self-ignition increases when the oil being used is dirty.
It is extremely important to note that overheating can cause a fire.
Never carry out any flambé cooking under the hood.
Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch off
the automatic circuit breaker).
It is very important to clean the hood and replace the filter at
the recommended intervals. Failure to do so could cause
grease deposits to build up, resulting in a fire hazard.
The appliance is not intended for use by young children or infirm
persons without supervision.
Older children must be supervised if using the appliance.
Young children should be supervised to ensure that they do not play
with the appliance.
WARNING - Ensure that the appliance is switched off before
replacing the lamp to avoid the possibility of electric shock.
This appliance is marked according to the European directive 2002/96/
EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of
this product.
The symbol on the product, or on the documents accompanying
the product, indicates that this appliance may not be treated as
household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For more detailed information about treatment, recovery and recycling
of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
66
For the installer
When used as an extractor unit, the hood must be fitted with a
150mm diameter hose.
Attention: The hose is not supplied and must be purchased
separately.
Should there already be a pipe of diameter 125 or 120 mm that ducts
to the outside through the walls, it is possible to use the 150/125-
120 mm reduction flange provided. In this case the hood will be
slightly noisier.
When installing the hood, make sure you observe the follow-
ing minimum distance from the top edge of the cooking hob/
ring surfaces:
electric cookers 500 mm
gas cookers 650 mm
If the instructions for installation for the gas hob specify a greater
distance, this must be adhered to.
The national Standard on fuel-burning systems specifies a maximum
depression of 0.04 mbar in such rooms.
The air outlet must not be connected to chimney flues or combustion
gas ducts. The air outlet must under no circumstances be connected
to ventilation ducts for rooms in which fuel-burning appliances are
installed.
The air outlet installation must comply with the regulations laid down
by the relevant local authorities.
When the unit is used in extraction mode, a sufficiently large
ventilation hole must be provided, with dimensions that are approxi-
mately the same as the outlet hole.
National and regional building regulations impose a number of
restrictions on using hoods and fuel-burning appliances connected to
a chimney, such as coal or oil room-heaters and gas fires, in the
same room.
Hoods can only be used safely with appliances connected to a
chimney if the room and/or flat (air/environment combination) is
ventilated from outside using a suitable ventilation hole approximately
500-600 cm
2
large to avoid the possibility of a depression being
created during operation of the hood.
If you have any doubts, contact the relevant controlling authority or
building inspector’s office.
Since the rule for rooms with fuel burning appliances is “outlet hole of
the same size as the ventilation hole”, a hole of 500-600 cm
2
, which
is to say a larger hole, could reduce the performance of the extractor
hood.
If the hood is used in its recirculation mode, it will operate simply
and safely in the above conditions without the need for any of the
aforementioned measures.
67
When the hood is used in its extraction mode, the following rules
must be followed to obtain optimal operation:
short and straight outlet hose
keep bends in outlet hose to a minimum
never install the hoses with an acute angle, they must always
follow a gentle curve.
keep the hose as large as possible (preferably the same diameter
as the outlet hole).
the length should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce the efficiency of the hood and
reduce the airflow.
Failure to observe these basic instructions will drastically reduce
the performance and increase the noise levels of the extractor
hood.
68
Description of the Appliance
The cooker hood is designed to extract unpleasant odours
from the kitchen, it will not extract steam.
The hood is supplied as an extractor unit and can also be used with
a recirculation mode by fitting a charcoal filter.
You will need an original charcoal filter for this function (Available
from your local Service Force Centre).
Only for HD 6470: The cooker hood is supplied ready for use as a
recirculation hood and may be used for extraction by removing the
charcoal filter which has been fitted inside the
cooker hood.
Extraction mode
In this mode fumes are extracted to the
outside via a hose connected to the coupling
ring A. Fig. 1.
In order to obtain the best performance the
hose should have a diameter equal to the
outlet hole.
Should there already be a pipe of diameter 125
or 120 mm that ducts to the outside through
the walls, it is possible to use the 150/125-120
mm reduction flange provided. In this case the
hood will be slightly noisier.
Recirculation mode
The air is filtered through a charcoal filter and
returned to the kitchen.
You will need an original charcoal filter for the
recirculation mode. (See Special Accessories).
Assemble the deflector (3 parts): the three
parts must be fixed with 2 screws Ø 3.5 13 mm,
the extension of the deflector is adjustable and
must correspond to the width of the chimney flue
support, to which it must be fixed.
Fix the deflector using 4 screws Ø 2,9x6.5 mm.
Fig. 2.
Optionally, the position of the chimney elements
can be changed.
When using the hood in the recirculation mode
the chimney must be fixed at the top, with the
air outlet grill at the side.
Fig. 1
coupling ring
Fig. 2
=
=
69
Control Panel
Model DM 8700 - DD 8770
Best results are obtained by using a low speed for normal conditions
and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or until
all the odours have disappeared. The control switches are located
on the hood’s front panel:
The hood operation may be controlled via the control ball or with the
remote control (the remote control is a special accessory and is
ordered separately).
Every status change (changing speed, switching on the lights, etc.)
is recognisable from the variation of light emitted by the control ball
and by an acoustic signal.
The control ball serves also as a light signal :
No signal :
The hood is switched off.
Static green light :
Hood is switched on at power level 1 (minimum).
Static orange light :
Hood is switched on at power level 2 (medium).
Static red light :
Hood is switched on at power level 3 (maximum).
Flashing red light :
Hood is switched on at intensive power level (timed at 5 minutes)
Flashing green light :
Indicates the grease filter saturation - clean the grease filter
Flashing orange light :
Indicates the charcoal filter saturation - clean or replace the
charcoal filter.
Attention!
The control ball flashes orange to indicate the saturation of the
charcoal filter even if the hood is used in the extraction mode and no
charcoal filter is fitted.
In this case, perform the signal reset operation as follows: select the
intensive speed (the control ball lights up with a red flashing light),
press again and hold pressed for about 3 seconds until an audible
signal indicates the reset has taken place.
70
Hood Operation - Model DM 8700 - DD 8770
Switching on the hood - Fig. 3
The control ball is a balancer switch.
Pressing the control ball repeatedly towards the right switches on the
hood and you may select the extraction level desired, pressing once
again on the right the hood switches off.
Switching on the light - Fig. 3
Press the control ball towards the left :
once for subdued lighting,
once again for full lighting,
press again to switch off the light.
press towards the
right to switch on the
hood
press towards the left
to switch on the light.
Fig. 3
Grease and charcoal filter maintenance
indicator
The air duct, in this hood, is provided with a device that signals when
the filter requires cleaning or changing .
Led signal for grease filter
The LED signal flickers (flickering green light) when the grease filter
requires cleaning, occurs at about 40 operating hours.
Carefully note the device for grease filter maintenance!
Led signal for charcoal filter
The LED signal flickers (flickering orange light) when the grease filter
requires cleaning, occurs at about 160 operating hours.
Re-setting the saturation signal
After cleaning or replacing the filter, select the intensive speed (the
control ball lights up with a red flashing light), press again and hold
pressed for about 3 seconds until a ‘bip’ sound indicates the reset.
71
Control Panel
Model DM 8600
Best results are obtained by using a low speed for normal conditions
and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or until
all the odours have disappeared. The control switches are located
on the hood’s front panel:
A - Mains switch, OFF.
B - Start and choice of motor speed 1-2-3
C - Indicates speed 1 (LED).
D - Indicates speed 2 and saturation of the grease filter (LED)
E - Indicates speed 3 and saturation of the charcoal filter (LED)
(flashing LED)
F - Indicates Intensive speed (LED).
G - Intensive speed on/off. The Intensive speed runs for 5 minutes:
If the hood is on when the Intensive speed is activated, the hood
reverts to previous speed after 5 minutes.
If the hood is off when the Intensive speed is activated, the hood
will be turned off after 5 minutes.
To interrupt the Intensive speed, press button A or B.
H - Light OFF
I - Light ON
Should the hood or the controls fail to operate: disconnect the power
supply for at least 5 seconds, then turn the hood back on again.
ABCDEFGH I
72
Grease and charcoal filter maintenance
indicator
This hood is fitted with a device that indicates when it is necessary to
clean the grease filter or the charcoal filter (if the hood is used in the
recirculation version with a charcoal filter).
On delivery, the hood is not supplied with a charcoal filter, so the
saturation indicator will be disabled.
If the hood is to be used with a charcoal filter, the saturation
indicator light must be enabled as follows:
Press buttons B and G simultaneously and hold them for 3 seconds.
At first only the grease filter LED D will light up, but when the charcoal
filter LED E lights up the saturation indicator will be enabled.
To disable it: Press buttons B and G again simultaneously and hold
them for 3 seconds, until the charcoal filter LED goes out.
Grease filter LED (D)
LED D will start to flash when it is time to clean the grease filter.
Cleaning will be necessary after 40 working hours. Always comply with
the maintenance instructions for the grease filter.
Charcoal filter LED (E)
The charcoal filter LED E will start to flash when the charcoal filter
needs to be replaced.
This operation is necessary after approximately 160 working hours.
Resetting the saturation indicator
After cleaning or replacing the filters, press button A for 3 seconds until
the grease filter LED D or the charcoal filter LED E stops flashing.the
grease filter LED D or the charcoal filter LED E stops flashing.
73
Control Panel
Model DM 8400 - HD 6470
Best results are obtained by using a low speed for normal conditions
and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or until
all the odours have disappeared. The control switches are located
on the hood’s front panel:
a- Indicator lamp
b- Light ON/OFF switch
c- Motor OFF - Speed 1 push-button
d- Speed 2 push-button
e- Speed 3 push-button
74
Maintenance and Care
The hood must always be disconnected from the electricity
supply before beginning any maintenance work.
Cleaning the hood
Clean the outside of the hood using a damp cloth and a solution of
water and mild washing up liquid.
Never use corrosive, abrasive or flammable cleaning products or
products containing bleach. .
Never insert pointed objects in the motor’s protective grid.
Only ever clean the switch panel and filter grill using a damp cloth
and mild washing up liquid.
It is extremely important to clean the unit and change the filters at
the recommended intervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
Metal grease filter
The purpose of the grease filters is to
absorb grease particles which form
during cooking and it must always be
used, either in the external extraction
or internal re-circulation function.
Attention: the metal grease filters
must be removed and washed, either
by hand or in the dishwasher, every
four weeks.
Removing the metal grease filter
Pull the handle downwards, then remove the filter. Fig. 4.
Hand washing
Soak grease filters for about one hour in hot water with a grease-
loosening cleaner, then rinse off thoroughly with hot water. Repeat
the process if necessary. Refit the grease filters when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select most powerful washing
programme and highest temperature, at least 65°C. Repeat the
process. Refit the grease filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
on its performance.
Clean the inner housing using a hand hot solution only(never use
caustic detergents, abrasive powders or brushes).
Fig. 4
75
i
g
h
g
g
g
Charcoal filter
The charcoal filter should only be used if you want to use the hood in
recirculation mode.
To do this you will need an original charcoal filter (available from your
local Service Force Centre).
Cleaning/replacing the charcoal filter
Unlike other charcoal filters, the LONGLIFE charcoal filter can be
cleaned and reactivated. With normal use the filter should be cleaned
every second month (when using the hood 2,5 hours per day,on
average). The best way to clean the filter is in the dishwasher. Use
normal detergent and choose the highest temperature (65º C). Wash
the filter separately so that no food particles stick to the filter and
later causes bad odours. To reactivate the charcoal, the filter should
be dried in an oven for 10 minutes with a maximum temperature of
100º C.
After approximately three years of use, the charcoal filter should be
replaced with a new, as the odour reduction capacity will be reduced.
Fitting
Remove the frame i which supports the filter h by turning 90° the two
knobs g.
Insert the charcoal filter inside the frame and put all parts back in
their place. Fig. 5.
To remove proceed in the reverse order.
Always specify the hood model code number and serial number
when ordering replacement filters. This information is shown on the
rating plate located on the inside of the unit.
The charcoal filter can be ordered from your local Service Force
Centre.
Fig. 5
76
Fig. 6
Warning
Failure to observe the instructions on cleaning the unit and changing
the filters will cause a fire hazard. You are therefore strongly
recommended to follow these instructions.
The manufacturer declines all responsibility for any damage to the
motor or any fire damage linked to inappropriate maintenance or
failure to observe the above safety recommendations.
Changing the light bulb
Disconnect the cooker hood from the mains supply.
Remove the lamp cover carefully, use a screw driver as a
lever. Fig. 6.
Replace the old bulb with a new one of the same type.
Refit the lamp cover.
If the light does not come on, make sure the bulb has been inserted
in correctly before contacting your local Service Force Centre.
Special accessories
Vapour screen see page 84
Remote control RM 8700 (only for model DM 8700 - DD 8770) 942 120 658
Charcoal filter Type 20
77
What to do if
If your appliance fails to work properly please carry out the following
checks.
Symptom Solution
The cooker hood will not start... Check that:
The hood is connected to
the electricity supply.
Check that a fan speed has
been selected
The cooker hood is not working Check that:
effectively.. The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented
to allow the entry of fresh air.
If set up for recirculation, check
that the charcoal filter is still
effective.
If set up for extraction, check that
the ducting and outlets are not
blocked.
The cooker hood has The safety cut-out device has been
switched off during operation... tripped.
Turn off the hob and then wait for
the device to reset.
If the hood has been installed
below the heights indicated in the
installation instructions the motor
will cut-out frequently which will
damage the hood.
If after all these checks, the problem persists, contact your local
Service Force Centre, quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for
any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have
been made as the engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
78
Technical assistance service (not for UK)
You are welcome to telephone our technical assistance service (see list of technical
assistance centres) whenever you need information or in the unlikely event of a fault.
For service in Australia call 1300 650 020.
When calling, please be ready to specify:
1. The model code number
2. The serial number (E-Nr.)
3. The manufacturing number (F-Nr.)
This information is shown on the registration plate inside the unit behind the
grease filter.
We reserve the right to change specifications and colours as a result of our policy of
continuing technological development.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts,
contact your local Service Force Centre by telephoning: 08705 929 929
Your call will be automatically routed to the Service Centre covering your post code
area. For the address of your local Service Force Centre and further information about
Service Force, please visit the website at www.serviceforce.co.uk
Please ensure that you have read the section „What to do if....“ as the engineer will make
a charge if the fault is not a mechanical or electrical breakdown even the appliance is
under warranty. Please note that proof of purchase is required for in-guarantee
service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
• Your name • Clear and concise details of the fault
Address and post code • Name and model of the appliance*
• Telephone number • E number*
• Serial number*
* This information can be found on the rating plate, which can be seen when the grease
filters are removed.
If you require Customer Service in the Republic of Ireland please contact us at
the address below:
AEG
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090751
79
Technical Specifications
Models DM 8600 DM 8700 DM 8400
HD 6470 DD 8770
Dimensions* - extractor version (in cm):
Height 66-112 70-113 66-112
Dimensions* - filter version (in cm):
Height 75,5-122 78-122 75,5-122
Maximum
absorbed power: 210 W 210 W 210 W
Motor absorption: 1 x 170 W 1 x 170 W 1 x 160 W
Lighting: 2 x 20W 2 x 20W 2 x 20W
Lenght of the cable: 150 cm 150 cm 150cm
Electrical connection: 220-240 V 220-240 V 230 V
Fuse rating:
5A Time Delay Fuse
* Width and depth depend on the glass body which is installed with the cooker hood,
see page 84
Mounting accessories included
1 deflector (3 pieces to assemble)
2 metal screws 3,5 x 13 (to assemble the deflector)
1 chimney support (3 pieces to assemble)
4 metal screws 4 x 8 (to assemble the chimney support)
4 metal screws 3,5 x 9,5 (to affix the deflector to the support)
2 metal screws 3 x 9 (Only for DD 8770 and HD 6470)
1 reduction flange Ø 125-120 mm
1 support bracket
5 wood-screws 5 x 45 mm (For brick or solid block installations only)
5 wall plugs Ø 8 mm (For brick or solid block installations only )
4 metal screws 2,9 x 6,5 (for chimney flue mounting)
4 metal screws 4 x 20 (to affix the screen to the cooker hood)
1 allen spanner (for TORX screws)
1 Vapour screen (Only for DD 8770 and HD 6470)
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your AEG appliance or for further information on AEG
products, please contact our Customer Care Department by letter or telephone at the
address below or visit our website at www.aeg.co.uk
Customer Services Department
Major Appliances
AEGElectrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 350 350 (*) * calls to this number may be recorded for training purposes.
80
Electrical connection (not for UK)
Safety warnings for the electrician
Before connecting the appliance to the power supply, check that the
voltage indicated on the rating plate corresponds to the mains power
supply available. Appliances fitted with a plug can be connected to any
standard power socket within easy access.
Should it be necessary to provide a fixed connection, the hood must
only be installed by an electrician authorised by the local electricity
board. When installing, an omnipolar disconnector with a distance of at
least 3 mm between contacts must be provided.
Fixed connection of the appliance must only be carried out by an
authorised electrician.
Electrical connection for UK only
Safety warnings for the electrician
Connect the hood to the mains supply via a double pole switch which
has 3 mm minimum separation between the contacts.
The switch must be accessible at all times.
The following is valid in the United Kingdom only:
- the wire which is coloured green and yellow must be connected to
the terminal which is marked with the letter E or by the earth symbol
( ), or coloured green or green and yellow;
- the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, -
- the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
81
Wall unit mounting - Fig. 7
First decide which functioning mode is better for you.
If you decide to use the hood in extraction mode we suggest you position
the upper section of the chimney so that the oulet slots are not visible
once installation is completed, however if is decided to use the hood in
rrecirculation mode BE SURE that the side with slots is up (see also A-B-
C sequence on on Fig. 7).
Assembling the chimney flue support/bracket (3 parts):
The three parts should be fixed with 4 screws, the support extension
is adjustable and should correspond to the internal width of the
telescopic chimney flue.
Assembling the deflector (3 parts – only for filter version):
The three parts should be fixed with 2 screws, the deflector
extension is adjustable and should correspond to the width of the
chimney flue support, to which it is then fixed.
A
B
180°
C - OK!
=
=
X
X
H
=
=
X
F
F
G
G
Fig. 7
82
Only for DD 8770 and HD 6470:
Assemble the frame to the motor group (a - Fig. 8.1).
Connect lamps and control panel to the motor housing (b - Fig. 8.1).
Fix the frame to the motor group using 2 screws (c - Fig. 8.1).
Mark the wall with a centre line, this will aid mounting procedure (1),
position the template so that the mid line printed on the template
matches with the centre line previously signed, the lower side of the
template corresponds to the lower side of the hood once mounted
(2).
Drill two holes Ø 8mm and fix the support bracket with two wall plugs
and screws (3).
Hang the hood (4) adjust its position (5-6) and from the inside of the
hood mark one point for definitive fixing (7), remove the hood and drill
a hole Ø 8mm (8), fit a wall plugs, hang the hood again and fix it
definitively with a screw (9).
Drill two holes Ø 8mm on the upper side close to the ceilling (10), fit
two wall plugs and fix the chimney support with two screws (11).
In case the hood is to be used in filter version, mount the deflector
F on the chimney support with four screws 2,9x6,5 and fit a vent
hose (12 - Not supplied - must be purchased) to connect deflector
to the outlet hole D of the hood.
In case the hood is to be used in extraction mode, then the deflector
must not be mounted and fit a vent hose (12 - Not supplied - must
be purchased) to connect outlet hole D of the hood to the outside.
Make electrical connection (13), but leave the hood disconnected
from the main circuit board.
Insert the vapour screen on the motor housing and fix it with four
screws M4x35 (14).
Fix the chimney first up (15a) to the chimney support (15b), then on
the bottom (16a) to the upper side of the frame (16b) using four
screws 2,9x6,5.
Connect the hood the the main circuit board and check if the hood
works properly.
Wall unit mounting - Fig. 8
84
Sonderzubehör/Wrasenschirm
Extra leverbare accessoires/Dampscherm
Accessoires/Séparateur de vapeur
Special accessories/Vapour screen
SM 8090
E-Nr. 942 120 654
SM 8091
E-Nr. 942 120 655
SM 8092
E-Nr. 942 120 656
SM 8093
E-Nr. 942 120 657
SM 8010
E-Nr. 942 120 743
89,9
50
89,8
50
105-85
50.3
50
60
88
50
89.8
89.9
50
70-80 (SM 8065 + BM 8005)
108-90 (SM 8085 + BM 8005)
BM 8005
E-Nr. 942 120 746
(NOT AVAILABLE FOR THE UK)
SM 8085 (88cm) - E-Nr. 942 120 744
SM 8065 (60 cm) - E-Nr. 942 120 745
1 / 1

Aeg-Electrolux HD6470-M User manual

Category
Cooker hoods
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document