Aeg-Electrolux DK3190-M User manual

Benutzerinformation

Gebruiksaanwijzing

Notice d'utilisation

User manual

Dunstabzugshaube

Afzuigkap

Hotte

Cooker Hood

DK 3160 - DK 3190

Page is loading ...

57

Contents

Safety warnings .............................................................................. 58

Description of the Appliance ......................................................... 60

Extraction mode ............................................................................... 60

Recirculation mode........................................................................... 60

Control Panel .................................................................................. 61

Maintenance and Care ................................................................... 62

Metal grease filter ............................................................................. 62

Charcoal filter ................................................................................... 63

Changing the light bulbs ................................................................... 64

Cleaning the hood .......................................................................... 64

Special accessories........................................................................ 64

Something Not Working................................................................. 65

Technical assistance service......................................................... 66

Service and Spare Parts................................................................... 66

Customer Care Department ............................................................. 67

Technical Details ............................................................................ 67

Mounting accessories included......................................................... 67

Electrical connection......................................................................... 68

Safety warnings for the electrician .................................................... 68

Installation ........................................................................................ 69

58

Safety warnings

• When used as an extractor unit, the hood must be fitted with a hose

having preferably the same diameter as the outlet hole.

Should there already be a pipe of diameter 125 mm that ducts to

the outside through the walls or roof, it is possible to use the 150/

125 mm reduction flange provided. In this case the hood will be

slightly noisier.

Attention: The hose is not supplied and must be purchased

separately.

• The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range hood

must be not less than 50cm from electric cookers and 65cm from

gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater

distance, this must be adhered to.

• Before any cleaning or maintenance operation, disconnect the hood

from the mains by removing the plug or disconnecting the home

mains switch.

• The appliance is not intended for use by children or persons with

impaired physical, sensorial or mental faculties, or if lacking in

experience or know-how, unless they are under supervision or have

been trained in the use of the appliance by a person responsible for

their safety.

• Children should be monitored to ensure that they do not play with

the appliance.

• Never use the hood without effectively mounted grating.!

• The hood must NEVER be used as a support surface unless

specifically indicated.

• The premises must be sufficiently ventilated, when the kitchen hood

is used together with other gas combustion devices or other fuels.

• The suctioned air must not be conveyed into a conduit used for the

disposal of the fumes generated by appliances that combust gases

or other fuels.

• The flaming of foods beneath the hood itself is severely prohibited.

• The use of exposed flames is detrimental to the filters and may

cause a fire risk, and must therefore be avoided in all

circumstances.

• Any frying must be done with care in order to make sure that the oil

does not overheat and burst into flames.

• As regards the technical and safety measures to be adopted for

fume discharging it is important to closely follow the relations

59

provided by the competent authorities.

• The hood must be regularly cleaned on both the inside and outside

(AT LEAST ONCE A MONTH, it is in any event necessary to

proceed in accordance with the maintenance instructions provided

in this manual)..

• Failure to follow the instructions as concerns hood and filter

cleaning will lead to the risk of fires.

• Do not use or leave the hood without the lamp correctly mounted

because of the possible risk of electric shocks.

• We decline any responsibility for any problems, damage or fires

caused to the appliance as the result of the non-observance of the

instructions included in this manual.

This appliance is marked according to the European directive 2002/96/

EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or on the documents accompanying

the product, indicates that this appliance may not be treated as

household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For more detailed information about treatment, recovery and recycling

of this product, please contact your local city office, your household

waste disposal service or the shop where you purchased the product.

60

*

B

F

1 x Ø 2,9x13

*

Ø 150

Ø 120-125

*

Description of the Appliance

• The cooker hood is designed to extract unpleasant odours from the

kitchen, it will not extract steam.

• The hood is supplied as an extractor unit and can also be used

with a recirculation mode by fitting a charcoal filter.

Extraction mode

• In this mode fumes are extracted to the outside via a hose

connected to the coupling ring. Fig. 1

• In order to obtain the best performance the hose should have a

diameter equal to the outlet hole.

Recirculation mode

• The air is filtered through a

charcoal filter and returned to

the kitchen. Fig. 2

• You will need an original

charcoal filter for the

recirculation mode.

(See Special Accessories).

Fig. 1

Top

Rear

Coupling ring

Top

Fig. 2

61

Control Panel

• Best results are obtained by using a low speed for normal

conditions and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking.

The hood should be left on after cooking for about 15 minutes or

until all the odours have disappeared.

The control switches are located on the unit’s front panel:

• the light switch switches the hood lamp on and off

• the motor switch switches the motor off

• Speed 1: Speed 1 push-button

• Speed 2: Speed 2 push-button

• Speed 3: Speed 3 push-button

Speed 1

Motor

Switch

Speed 2 Speed 3 Light switch

62

Maintenance and Care

Warning! Before performing any maintenance operation, isolate the

hood from the electrical supply by switching off at the connector and

removing the connector fuse.

Or if the appliance has been connected through a plug and socket,

then the plug must be removed from the socket.

Metal grease filter

• The purpose of the grease filters is to absorb grease particles which

form during cooking and it must always be used, either in the

external extraction or internal re-circulation function.

Attention: the metal grease filters must be removed and washed,

either by hand or in the dishwasher, every four weeks.

Removing the metal grease filters

• Push it towards the back of the unit and then pull it down and out.

Fig. 3.

Hand washing

Soak grease filters for about one hour in hot water with a grease-

loosening cleaner, then rinse off thoroughly with hot water. Repeat

the process if necessary. Refit the grease filters when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select most powerful

washing programme and highest temperature, at least 65°C.

Repeat the process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight

discolouration of the filter can occur, this does not have any impact

on its performance.

• Clean the inner housing using a hand hot solution only(never use

caustic detergents, abrasive powders or brushes).

Fig. 3

63

Charcoal filter

• The charcoal filter should only be used if you want to use the hood

in recirculation mode.

• Cleaning/replacing the carbon filter

The saturation of the activated charcoal occurs after more or less

prolonged use, depending on the type of cooking and the regularity

of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least every

four mounths.

The carbon filter may NOT be washed or regenerated.

• Fitting

Remove the grease filters.

Fit the charcoalfilters over the motor.

Align the pins R on the cowl with the slots S, then turn the filter

clockwise until it locks in place.

Refit the grease filters. Fig. 4.

• To remove proceed in the reverse order.

• Always specify the hood model code number and serial number

when ordering replacement filters. This information is shown on the

rating plate located on the inside of the unit.

• The charcoal filter can be ordered from your local Service Force

Centre.

Fig. 4

R

S

R

*

64

Warning

• Failure to observe the instructions on cleaning the unit and changing

the filters will cause a fire hazard. You are therefore strongly

recommended to follow these instructions.

• The manufacturer declines all responsibility for any damage to the

motor or any fire damage linked to inappropriate maintenance or

failure to observe the above safety recommendations.

Changing the light bulbs

• Disconnect the appliance from the power supply.

• Warning! Make sure lamps are cold before touching them.

• Remove the clip that secures the lamp cover, then prise off using a

small screwdriver or other suitable tool.

• Replace the burnt-out bulb. Use a 40W max (E14) bulb only.

• Refit the lamp cover and secure in place with the clip.

Note: the lamp can also be accessed by removing the grease

filters, but removing the lamp in this way is more difficult.

Cleaning the hood

• Clean the outside of the hood using a damp cloth and a solution of

water and mild washing up liquid.

• Never use corrosive, abrasive or flammable cleaning products or

products containing bleach.

• Never insert pointed objects in the motor’s protective grid.

• Only ever clean the switch panel and filter grill using a damp cloth

and mild washing up liquid.

• It is extremely important to clean the unit and change the filters at

the recommended intervals. Failure to do so will cause grease

deposits to build up that could constitute a fire hazard.

Special accessories

Charcoal filter TYPE 29

Fig. 5

65

Something Not Working

If your appliance fails to work properly please carry out the following

checks.

Symptom Solution

The cooker hood Check that: The hood is connected to

will not start... the electricity supply.

Check that a fan speed has been

selected

The cooker hood Check that: The fan speed is set

is not working high enough for the task.

The grease filters are clean.

The kitchen is adequately vented to

allow the entry of fresh air.

If set up for recirculation, check that

the charcoal filter is still effective.

If set up for extraction, check that the

ducting and outlets are not blocked.

The cooker hood has The safety cut-out device has been

switched off tripped.

during operation... Turn off the hob and then wait for

the device to reset.

If the hood has been installed below

the heights indicated in the

installation instructions the motor

will cut-out frequently which will

damage the hood.

If after all these checks, the problem persists, contact your local

Service Centre, quoting the model and serial number.

Please note that it will be necessary to provide proof of purchase for

any in-guarantee service calls.

In-guarantee customers should ensure that the above checks have

been made as the engineer will make a charge if the fault is not a

mechanical or electrical breakdown.

66

Technical assistance service (not for UK)

You are welcome to telephone our technical assistance service (see list of technical

assistance centres) whenever you need information or in the unlikely event of a fault.

For service in Australia call 1300 650 020.

When calling, please be ready to specify:

1. The model code number

2. The serial number (E-Nr.)

3. The manufacturing number (F-Nr.)

This information is shown on the registration plate inside the unit behind the

grease filter.

We reserve the right to change specifications and colours as a result of our policy of

continuing technological development.

Service and Spare Parts

In the event of your appliance requiring service, or if you wish to purchase spare

parts, contact your local Service Force Centre by telephoning: 08705 929 929

Your call will be automatically routed to the Service Centre covering your post code

area. For the address of your local Service Force Centre and further information

about Service Force, please visit the website at www.serviceforce.co.uk

Please ensure that you have read the section “What to do if...” as the engineer will

make a charge if the fault is not a mechanical or electrical breakdown even the

appliance is under warranty. Please note that proof of purchase is required for in-

guarantee service calls.

Help us to help you

Please determine your type of enquiry before writing or telephoning.

When you contact us we need to know:

• Your name • Clear and concise details of the fault

• Address and post code • Name and model of the appliance*

• Telephone number • E number*

• Serial number*

* This information can be found on the rating plate, which can be seen when the

grease filters are removed.

If you require Customer Service in the Republic of Ireland please contact us at

the address below:

AEG

Electrolux Group (Ire) Ltd

Long Mile Road

Dublin 12

Republic of Ireland

Tel: + 353 (0) 1 4090751

Email: [email protected]

67

CUSTOMER CARE DEPARTMENT

For general enquiries concerning your AEG appliance or for further information on

AEG products, please contact our Customer Care Department by letter or telephone

at the address below or visit our website at www.aeg.co.uk

Customer Services Department

Major Appliances

AEGElectrolux

Addington Way

Luton

Bedfordshire

LU4 9QQ

08705 350 350 (*)

* calls to this number may be recorded for training purposes

Technical Details

DK 3160 DK 3190

Dimensions (in cm):

Height: 19,7 19,7

Width: 60 90

Depth: 45 45

Max. absorb. power: 200 W 200 W

Motor: 120 W 120 W

Lighting: 2 x 40 W 2 x 40 W

Length of the cable: 150 cm 150 cm

Electrical connection: 220-240 V 220-240 V

Mounting accessories included

1 allen wrench (for TORX screws)

1 deflector

1 reduction flange Ø 125-120 mm

1 chimney support

5 wood-screws 5 x 45 mm (for wall mounting)

5 wall dowel Ø 8 mm (for wall mounting)

2 washers

1 screws 2,9 x 13 (to fix the deflector)

2 metal screws 3 x 9 (to fix the upper chimney)

68

Electrical connection

Safety warnings for the electrician

The mains power supply must correspond to the rating indicated on

the plate situated inside the hood. If provided with a plug connect the

hood to a socket in compliance with current regulations and positioned

in an accessible area. If it not fitted with a plug (direct mains

connection) or if the plug is not located in an accessible area apply a

bi-polar switch in accordance with standards which assures the

complete disconnection of the mains under conditions relating to over-

current category III, in accordance with installation instructions.

IMPORTANT: Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that the

mains cable is correctly assembled.

69

÷ 10 mm

3 x Ø 8mm

1 x 5x45

Installation

• Mark a centre-line on the wall from the cooktop to the ceiling. Fig 6

• Bearing in mind the minimum heights over the cooktop specified

above, mark the height of the hood on the wall with a pencil and

place the template against the wall on the mark. Fig 7

• Using the template supplied, mark the holes, drill them and insert

the rawlplugs, partly tighten 1 screw in the top rawlplug. Fig 8

Fig. 6 Fig. 7

Fig. 8

= =

70

• Fix the flue support to the wall as close as possible to the ceiling.

Fig 9

Fig. 9

• Hook the hood. Fig 10

Fig. 10

= =

G

Ø 8

Ø 5x45

71

• Adjust the position. Fig 11

Fig. 11

• Fully tighten the top fixing screw. Fig 12

Fig. 12

• Remove the grease filters and fix the hood from inside using 2

screws and washers. Fig 13

Fig. 13

72

• Depending on hood version:

Extractor Version:

Fix an exhaust duct with the right diameter to the exhaust outlet of

the hood and connect to an exhaust system ducted to the outside

(for fixture and connection of exhaust duct, utilize the most suitable

system for the duct purchased). Fig 14

Filter Version:

Install the filter connection F on the collar B and secure with 1

screw. Fig 15

• Connect the hood to the power supply!

Fig. 14

Fig. 15

• Fix the telescopic flue tot he support with two screws. Fig 16

Fig. 16

Ø 150

Ø 120-125

*

B

F

1 x Ø 2,9x13

*

2 x Ø 3x9

H

2 x Ø 3x9

H

• Slide the bottom section down into its seat on the top of the hood.

Fig 17

Fig. 17

OK!

H

Page is loading ...

Aeg-Electrolux DK3190-M User manual

Aeg-Electrolux DK3190-M User manual

in other languages

Related papers

Other documents