De Dietrich DOP505XE1 Owner's manual

DOP505*

Le guide d’utilisation de votre four

User Manual for Your Oven

Betriebsanleitung des Backofens

De gebruikshandleiding van uw oven

B

rugervejledning til ovnen

La guía de utilización del horno

O guia de utilização do seu forno

FR

GB

DE

NL

DK

ES

PT

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 1

2

Tout au long de la notice,

vous signale les consignes de sécurité,

vous signale les conseils et les astuces

Edito P.3

Comment se présente votre four ?

Descriptif de l’appareil P.4

Accessoires P.5

Conseils de sécurité P.6

Comment installer votre four ?

Raccordement électrique P.7

Changement du câble d’alimentation P.8

Dimensions utiles pour encastrer votre four P.9

Comment utiliser votre four ?

Le détail de votre programmateur P.10

Comment mettre à l’heure l’horloge du four ? P.11

Comment faire une cuisson immédiate ? P.12

Comment programmer une cuisson ? P.13-14

Comment utiliser le minuteur ? P.15

Modes de cuisson du four P.16-17

Comment entretenir votre four ? P.18-19

Comment changer l’ampoule ? P.20

Que faire en cas d’anomalies de fonctionnement P.20

Qui contacter ?

P.21

Sommaire

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 2

Page is loading ...

1

3

5

SETSET

ECO

4

C

omment se présente votre four ?

1

2 3

4

5

7

6

1

2

5

6

7

3

4

Réglage de la température

Programmateur

Sélecteur de fonctions

Lampe

Indicateur de gradin

Trou pour tourne broche

Contact de détection

d’ouverture de porte

DESCRIPTIF DE L’APPAREIL

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 4

Page is loading ...

7

FR

Comment installer votre four ?

Compteur 20A Mono

220-240 V ~ 50 Hz

Prise de courant

2 pôles + terre

norme CEI 60083

Ligne Mono 220-240 V ~

Raccordement électrique

Câble

d'alimentation

longueur 1,50 m

environ

Disjoncteur différentiel ou

fusible 16A

Avant d'effectuer le branchement, s'assurer que les fils de votre

installation électrique sont d'une section suffisante pour alimen-

ter normalement l'appareil.

Le fusible de votre installation doit être de 16 Ampères.

Le raccordement électrique est à réaliser avant la mise en place de l'appareil

dans le meuble.

• Le four doit être branché avec un câble d'alimentation (normalisé) à 3 conduc-

teurs de 1,5 mm

2

(1 ph +1 N + terre) qui doivent être raccordés sur réseau

220-240 V ~ monophasé par l'intermédiaire d'une prise de courant 1 ph +1 N +

terre normalisée CEI 60083 ou conformément aux règles d’installation. Le fil de

protection (vert-jaune)

est relié à la borne de l'appareil et doit être relié à la

terre de l'installation.

• Dans le cas d’un branchement avec prise de courant,

celle-ci doit rester accessible après l’installation de l’appareil.

• Le neutre du four (fil bleu) doit être raccordé au neutre du réseau.

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 7

Page is loading ...

10

Comment utiliser votre four ?

SET

1. Le détail de votre programmateur

Affichage des températures, temps, durées et minuteur

Indicateur d’affichage de la température

Indicateur d’affichage de la durée de cuisson

Indicateur d’affichage de la fin de cuisson

Indicateur d’affichage du minuteur indépendant

Touche d’accès aux différents programmes de réglage

1

3

4

5

6

2

6

2

3

4

5

1

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 10

11

Comment utiliser votre four ?

a) A la mise sous tension

• L’afficheur clignote à 12h.

• Réglez l’heure à l’aide du sélecteur de réglage

+ ou - (le maintien sur + ou - permet d’obtenir

un défilement rapide).

• Appuyez sur la touche SET pour valider.

Exemple:12h30.

b) Remise à l’heure de l’horloge

• Restez appuyé quelques secondes sur SET,

000 apparait, relâchez ->l’heure clignote.

• Ajustez le réglage de l’heure avec le sélecteur de ré-

glage ( + ou –).

• Appuyez sur la touche SET pour valider.

SET

2. Comment mettre à l'heure l’horloge du four ?

S’il n’y a pas de validation par la touche SET, l’enregistrement

est automatique au bout de quelques secondes.

SET

FR

99636072_ML_ DOP505.qxd 17/03/05 15:39 Page 11

Page is loading ...

FR

17

mément à la norme européenne EN 50304 et selon la directive Européenne 2002/40/CE.

Recommandé pour les quiches,

tourtes, tartes aux fruits juteux.

Recommandé pour griller les

côtelettes, saucisses, tranches de

pain, gambas posées sur la grille.

Recommandé pour faire lever les

pâtes à pain, à brioche, kouglof...en

ne dépassant pas 40°C (chauffe-

assiettes, décongélation).

Recommandations

Modes de cuisson du four

Recommandé pour garder le moelleux des

viandes blanches, poissons, légumes

Pour les cuissons multiples jusqu’à 3 niveaux.

Nota : toutes les cuissons se font sans

préchauffage.

Recommandé poursaisir et cuire à coeur

viandes rouges et blanches.

Pour cuire doucement les volailles jusqu’à

2 kg

Préco T°

mini

préco

maxi

35

180

235

mini

préco

maxi

35

205

275

mini

préco

maxi

200

230

mini

préco

maxi

35

275

mini

préco

maxi

35

80

100

180

200

mini

préco

maxi

1

4

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 17

Page is loading ...

22

Throughout the manual,

indicates safety recommendations,

indicates advice and tips

Introduction P.23

What does your oven look like?

Description of the appliance P.24

Accessories P.25

Safety Recommendations P.26

How do you install your oven?

Electrical connection P.27

Changing the power cable P.28

Useful dimensions for installing your oven P.29

How does your oven work?

Close-up view of your programmer P.30

How do you set the clock on the oven? P.31

How do you program for immediate cooking? P.32

How do you set a cooking programme? P.33-34

How does the timer work? P.34

How do you program for Eco cooking? P.35

Oven cooking modes P.36-37

How do you care for your oven? P.38-39

How do you change the bulb? P.40

What do you do in case of operating malfunctions? P.40

Table of Contents

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 22

23

GB

Introduction

Dear Customer,

You have just acquired a DE DIETRICH oven and we would like to thank you.

Our research teams have created a new generation of appliances for you. Their

quality, design and technological advances make them exceptional products

and reveal our unique know-how.

With modern, refined lines, your new DE DIETRICH oven blends harmoniously

into your kitchen and perfectly combines technological expertise, cooking per-

formance and aesthetic luxury.

In the line of DE DIETRICH products, you will also find a wide range of hobs,

ventilation hoods, dishwashers, microwave ovens and refrigerators, all of which

can be built in and all of which can be coordinated with your new DE DIETRICH

oven.

Thanks to these "New Items of Value" that serve as guideposts in our every-

day lives, DE DIETRICH, the reference of excellence, is truly an invitation to a

new art of living.

The DE DIETRICH brand.

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 23

1

3

5

SETSET

ECO

24

W

hat does your oven look like?

1

2 3

4

5

7

6

1

2

5

6

7

3

4

Temperature setting

Programmer

Function selector

Light

Shelf support indicator

Hole for rotisserie

Contact for open door

detector

DESCRIPTION OF THE APPLIANCE

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 24

Accessories

GB

Dish + grid (drip tray)

Inserted under the grid, it catches barbecue

juices and grease. it can also be used half-full

of water for double-boiler cooking methods

Avoid placing roasts or meats directly in the

dish because you are certain to have major

spattering on the oven walls

25

Rear

Front

Curved anti-tipping safety grid

Its shape was designed to allow you to position

your dish between two shelf support levels.

Rotisserie (optional)

To use it:

• Place the multi-purpose baking tray at level

no. 1 to collect the cooking juices or on the

bottom of the oven if the piece of meat to be

roasted is too big.

• Slide one of the forks onto the spit; put the

piece of meat to be roasted onto the spit; slide

on the second fork; centre and tighten the two

forks.

• Place the spit on its cradle.

• Push gently to locate the tip of the spit in the turning mechanism situated at the

back of the oven.

• Remove the handle by unscrewing it. After cooking, screw the handle back onto

the spit to take it out without burning yourself.

At the end of the handgrip, a depression enables you to unscrew the forks.

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 25

26

Safety Recommendations

Please become familiar with these recommendations before installing

and using your oven. This oven was designed for household use only. It is

intended solely for cooking foodstuffs. This oven does not contain any asbestos-

based components.

FIRST USE:

Before using your oven for the first time, heat it up while empty with the door

closed for approximately 15 minutes using the maximum setting in order to “cure”

the appliance. The rock wool that surrounds the oven cavity may initially release

a particular odour caused by its composition. Similarly, you may notice the release

of some smoke. All of this is normal.

SUBSEQUENT USES:

- Ensure that the door of your oven is completely closed so that the seal

can properly do its job.

- Do not let anyone lean against or sit on the oven door when it is open.

- When using the grill with the door semi-open, exposed parts

and surfaces may become hot. Keep small children away.

- When in use, the appliance becomes hot. Be careful not to touch the heat-

ing elements located inside the oven.

- After cooking, do not use bare hands to touch the dishes or accessories

(grid, rotisserie, drip tray, rotisserie support, etc.); use a potholder or heat-resistant

material.

- Do not use a steam cleaner or high-pressure cleaner.

- Do not line your oven with sheets of aluminium. Otherwise, the result

could be an accumulation of heat that could have an undesirable effect on cook-

ing and roasting results and could damage the enamel.

The oven must be turned off for all attempts to clean the cavity.

During pyrolysis, the exposed surfaces become hotter than during

normal use. It is advisable to keep small children at bay.

Before beginning a pyrolysis cycle, remove all grids and trays.

If the appliance has an electrical connection, it must remain

accessible after the appliance has been built in.

The function selector absolutely must be returned to 0 in order to

use your oven again.

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 26

27

GB

How do you install your oven?

Monophase 20A Counter

220-240 V ~ 50 Hz

Electrical outlet

2 prong receptacle

+ ground lead

CEI Standard 60083

Monophase line 220-240 V ~

Electrical connection

Power cable

approximately

1.5 m in length

16A fuse or differential

circuit breaker

Before making the connection, ensure that the wires in your elec-

trical installation have enough cross-sectional area to properly

supply electricity to the appliance.

The fuse in your set-up must be 16 amperes.

The electrical connection should be performed before the appliance is installed in

the cabinet.

•

The oven must be connected with a power cable (standardised) with three 1.5 mm

2

conductors (1 ph +1 N + ground) that must be connected to a monophase 220-240 V

network via a CEI 60083 standardised receptacle (1 ph +1 N + ground lead) or in ac-

cordance with installation rules. The safety wire (green-yellow) is connected to the ap-

pliance's terminal and must be connected to the ground lead of the electrical set-up.

• In the case of connections with an electric receptacle, it must remain accessible

after installation of the appliance.

• The oven's neutral conductor (blue wire) must be connected to the network's

neutral conductor.

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 27

28

• The power cable (H05 RR-F, H05 RN-F or H05 VV-F) must be of sufficient length to

be connected to the build-in oven while it sits on the floor in front of the cabinet.

To do this the appliance must be disconnected from the electrical network:

• Open the inspection flap located at the lower right of the back cover by un-

screwing the two screws, then pivot the inspection flap.

• Strip 12 mm along each wire of the new power cable.

• Carefully twist together the strands.

• Loosen the screws from the terminal board and remove the power cord to be re-

placed.

• Introduce the power cable through the side of the cover in the cable clip located

to the right of the terminal board.

• Connect the power cord wires in accordance with the written markings on the

terminal board.

• All the strands of the electricity wires must be captured under the screws.

• The phase wire on the L terminal.

• The green-yellow coloured ground wire should be connected to the terminal .

• The neutral conductor (blue) on the N terminal.

• Screw down tightly the screws on the terminal board and check the connection by

pulling on each wire.

• Attach the cable with the cable clip located to the right of the terminal board.

• Close the inspection flap using the two screws.

Changing the power cable

We cannot be held responsible for any accident resulting from an

non-existent, defective or incorrect ground lead.

How do you install your oven?

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 28

29

GB

How do you install your oven?

To be certain that you have properly installed your appliance, do

not hesitate to call on a household appliance specialist.

Useful dimensions for installing your oven

The oven can be installed under a work top or in a column of cabinetry

(open* or closed) having the appropriate dimensions for built-in instal-

lation (see adjacent diagram).

Your oven has optimised air circulation that allows it to achieve remarkable cooking

and cleaning results if the following guidelines are respected:

• Centre the oven in the cabinet so as to guarantee a minimum distance of 5 mm

between the appliance and the neighbouring cabinet.

• The material of the built-in cabinetry must be heat resistant (or be covered with

such a material).

• For greater stability, attach the oven in the cabinet with two screws through the

holes provided for this purpose on either side of the front inner panel (see diagram).

To do this:

1) Remove the rubber screw covers to access the mounting holes.

2) Drill a Ø 3 mm hole in the cabinet panel to avoid splitting the wood.

3) Attach the oven with the two screws.

4) Replace the rubber screw covers (they also serve to absorb the shock caused

by closing the oven door).

(*) If the cabinet is open, its opening must be 70 mm (maximum).

70

550

Location of

retaining screw

50 x 50 mm cut-out

Location of

retaining screw

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 29

30

How does your oven work?

1. Close-up of your analog programmer

Display for temperatures, times, cooking times and timer

Temperature display indicator

Cooking time display indicator

End of cooking display indicator

Independent timer display indicator

Touch control for accessing various time setting programmes

1

3

4

5

6

2

SET

6

2

3

4

5

1

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 30

31

GB

a) When supplied with electricity

• The display flashes.

• Set the time by turning the + or – selector (contin-

ual turning of the + or – selector allows for rapid

number advancement)

• Press the SET touch control to enter.

Example: 12:30.

b) Resetting the clock time

• Press SET for a few seconds, 000 appears, release

-> the time blinks.

• Adjust the time with the selector (+ or –).

• Press the SET touch control to enter.

2. How do you set the oven clock?

If the SET touch control is not pressed, the adjustment

will be automatically recorded after a few seconds.

How does your oven work?

SET

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 31

32

How does your oven work?

3. How do you program for immediate cooking?

The analog programmer should display only the time; it should not be flashing.

• Choose the cooking mode:

Turn the function selector to the position of your

choice.

Example: position " "-> the oven turns on.

Your oven recommends the most commonly used tem-

perature.

Place your dish in the oven based on the recommen-

dations provided by the cookbook.

It is, however, possible to adjust the temperature by turn-

ing the selector toward + or –.

Example " " set to 210°.

After these steps, the oven begins to heat up and the display alternates between

the temperature in the oven and the temperature selected.

A series of beeps will be emitted when the oven reaches the selected tempera-

ture. Once this temperature is reached, it remains on the display.

The symbol continues blinking.

After a cooking cycle, the circulating fan continues to function for a peri-

od in order to cool the oven.

SET

ECO

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 32

33

GB

How does your oven work?

4.

How do you set a cooking programme?

a) With immediate start

1. Set the desired cooking mode and adjust the tempera-

ture if necessary.

Example: position “ ”

Temperature 200°C.

2. Press the SET touch control until the cooking time indi-

cator flashes “ ”.

The display flashes 0:00 to indicate that you can now

adjust the setting.

3. Turn the + or - selector to set the desired time.

Example: 25 min cooking time.

The cooking time is automatically recorded after a few sec-

onds -> the display no longer flashes and returns to tem-

perature display mode.

The countdown of the length of time begins immediately

after it has been set.

After these three steps, the oven heats up:

A series of beeps will be emitted when the oven reaches the selected temperature.

At the end of cooking (end of programmed time),

- the oven stops

- the cooking time indicator turns off

- 0:00 is displayed

- a series of beeps is emitted for a few minutes.

The beeping sound stops definitively when the function selector is reset to 0.

After a cooking cycle, the circulating fan continues to function for a peri-

od in order to cool the oven.

SET

ECO

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 33

34

How does your oven work?

b) With delayed start (choose end time)

Proceed as with programmed cooking.

After setting the cooking time,

Press the SET touch control until the end of cooking

indicator flashes “ ”.

The display flashes 0:00 to indicate that you can now

adjust the setting.

Turn the + or – selector to set the desired cooking

end time.

Example: End of cooking at 13:00.

After these steps, the oven heating is delayed so that

cooking ends at 13:00.

At the end of cooking (end of programmed time),

- The oven stops

- The cooking time indicator turns off

- 0:00 is displayed

- A series of beeps is emitted for a few minutes.

The beeping sound stops definitively when the function selector is reset to 0.

After a cooking cycle, the circulating fan continues to function for a peri-

od in order to cool the oven.

SET

99636072_ML_ DOP505.qxd 17/03/05 15:40 Page 34

Page is loading ...

De Dietrich DOP505XE1 Owner's manual

This manual is also suitable for

De Dietrich DOP505XE1 Owner's manual

in other languages

Related papers

Other documents