Emerson ER100104 Wireless Charging Alarm Clock Owner's manual

Emerson
Brand
Emerson
Model
ER100104 Wireless Charging Alarm Clock
Category
Alarm clocks
Type
Owner's manual

This manual is also suitable for

Emerson ER100104 Wireless Charging Alarm Clock features a large LED display that shows time, date, and temperature. It has dual alarms that can be set independently, and both alarms can be programmed for everyday operation, weekdays only, or weekends only. The clock also has a snooze button and a dimmer switch to adjust the brightness of the display. On the top of the clock, there is a wireless charging pad that can be used to charge Qi-enabled devices such as smartphones and tablets.

Emerson ER100104 Wireless Charging Alarm Clock features a large LED display that shows time, date, and temperature. It has dual alarms that can be set independently, and both alarms can be programmed for everyday operation, weekdays only, or weekends only. The clock also has a snooze button and a dimmer switch to adjust the brightness of the display. On the top of the clock, there is a wireless charging pad that can be used to charge Qi-enabled devices such as smartphones and tablets.

AL1 AL2
DIMMER
LIGHT
TEMP.
Package Contents
ER100104
ER100104
2
White
Press “ ” or “ ” button to adjust Year.
ALARM1 Button
TUNE UP /DOWN Button
Setting the Year
Setting the Date
Setting the Time
8
TIME ZONE
WARNING
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
11.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
12.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
13.) Mains plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from
the mains completely, the mains plug should be disconnected from the
mains socket outlet completely.
14.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
IMPORTANT SAFETY INSTRUCTIONS
PRÉCAUTION: Danger d’explosion si les piles sont remplacées de facon incorrect.
Remplacer les piles seulement par le méme type de pile ou
l’équivalent.
· minimum distances 10 cm around the apparatus for sufficient ventilations.
10cm de distance minimale autour de l’appareil pour une ventilation suffisante.
·t he ventilation should not be impeded by covering the ventilation openings with items such
as newspaper, table-cloths, curtains etc.
Ne pas recouvrir les entrées d’aérations avec des objets tel qu’un journal, une nappe, un
rideau, etc…
· no naked flame sources such as lighted candles should be placed on the apparatus.
Aucune source de flamme nue, tel qu’une bougie, ne doit être placée sur l’appareil.
·attention should be drawn to the environmental aspects of battery disposal.
Les piles usages doivent être jetées en respectantl’environnement.
·the use of apparatus in tropical and/or moderate climates.
L’utilisation de l’appareil dans un climat tropical et/ou modéré
* Les marquages sont inscrits en bas de l'appareil. Les précautions d'emploi sont inscrites
en bas de l'appareil.
La prise du secteur ne doit pas ētre obstruée ou doit ētre facilement accessible pendant
son utilisation.
Pour étre complètement déconnecté de l'alimentation d'entrée, la prise doit ētre
débranchée du secteur.
Les piles ne doivent pas ētre exposées à de forte chaleur, tel qu'á la lumière du soleil, au
feu ou autres choses de semblable.
La prise du secteur est utilisé pour déconnecter le système.
La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant
son utilisation.
Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être
débranchée du secteur.
L’adaptateur AC/AC de l’appareil est utilisé pour déconnecter le système.
L’adaptateur AC/AC de l’appareil ne doit pas être obstrué ou doit être facilement
accessible pendant son utilisation.
Pour être complètement déconnecté de l’alimentation d’entrée, l’adaptateur AC/AC de
l’appareil doit être déconnecté du secteur.
WARNING
Do not ingest the battery,Chemical Burn Hazard
This product contains a coin/button cell battery.
If the coin/button is swallowed,it can cause severe internal burns
in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely,stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside
any part of the body,seek immediate medical attention.
Thank you for purchasing this Emerson SmartSet Dual Alarm Clock Radio.
This clock radio uses Emerson's patented SmartSet Automatic Time Setting
System. The first time you connect this clock radio to your AC outlet, and
after every power interruption, within seconds the clock will automatically
set itself t o t he cor r ect Ye a r, M o n t h , D a t e , D a y, and Time. In a d d i tion a l l
changes from Standard Time to Daylight Saving Time, and back to Standard
Time, are made automatically.There are dual alarms that can be set and used
independently, and both of the alarms can be programmed for everyday
operation, weekdays only, or weekends only.There is a long life lithium battery
installed in this clock radio when you buy it.This battery can maintain the time and
alarm settings for 3 to 5 years, or even longer.We have taken every precaution to
make sure this radio was in perfect working order when it left our factory.
If you encounter any problems with the set up or operation of this item, please
call the Emerson Consumer Products Corp.,Customer Service Hotline, toll free,
at 1 -800-898-9020.
®
®
1
3
4
5
6
7
2
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to p rovide
rea s onabl e prote c tion a g ainst h armfu l interf erenc e i n a resi d entia l installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful inter f erenc e to radi o
com m unica t ions. H oweve r, there i s no guar antee t h at interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tu rning the equipment off and on,
the user is en couraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.This device
complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Changes or modificati ons not expressly approved by the party responsibl e f or
compliance could void the user's authority to operate the equipment.
Wireless Charging
AM
AL1
AL2
AM
AL1
AL2
AL1 AL2
DIMM ER
LIGH T
TEMP.
9
10
11
12
13
14
AM
AL1
AL2
ALARM2 Button
LED ON/OFF Button
SNOOZE
TEMPERATURE Button
TIME/CLOCK SET Button
TIME ZONE Button
USB CHAR.
TIME
1
SET ZONE
LED Decor and Temperature Sensor
15
12.Qi Wireless Charging Pad
Th e ex cla ma tio n p oin t w ith in
an eq u i lat e r al tri a n gle i s i n -
t e n d e d t o a l e r t t h e u s e r t o
t h e p r e s e n c e o f i m p o r t a n t
o perating a n d maintenance
( s e r v i c i n g ) i n s t r u c t i o n s i n
t h e l i t e r a t u r e a c c o m p a n y -
i n g t h e a p p l i a n c e.
The lightning flash with arrow-
head symbol , wi thin a n eq ui-
later al tri angle is i ntended to
alert the user to the presence
of uninsulated 'dangerous voltage'
within the product's enclosure
t h a t m a y b e o f s u f f i c i e n t
magnitude to constitute a risk
of ele ctric sho ck to p ers on s.
WAR NI NG: TO R ED UC E TH E R IS K OF
EL EC TRIC S HO OK DO NO T R EM OV E
COVER (OR BACK),NO USER SERVICEABLE
PA RT S I N SI DE R E FE R SE RV I CI N G T O
QU AL IFIED SERV ICE PE RS ON NE L.
AVIS:R ISQ UE DE CHOC
E L E C T R I Q U E - N E PA S O U V R I R
POUR ÉVITER TOUT DANGER DE CHOC ÉLECTRIQUE, NE PAS
RACCORDER AU SECTEUR TANT QUE LA GRILLE N'APAS ÉTÉ REMISE
EN PLACE.POUR RÉDUIRE LE RISQUE D’INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PAS EXPOSER CET APPAREIL SOUS LA PLUIE
ET L’HUMIDITÉ.
.
TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT CONNECT TO MAINS
POWER SUPPLY WHILE GRILLE IS REMOVED.TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
Read This Insert
(Quick Start Guide)
Qi Wireless Charging Indicator
('slow flashing red'=Charging;
'fast flashing red'=Charging error;
'steady green'=Charging complete)
Press
1617
SNOOZE/DIMMER Button
15.
16.
17.
14.
13.Temperature Sensor (-4~176 F)
11.
until current time zone flashes. Then, release the button and press
the “▼” or “▲” button to adjust it to your desired time zone. Press
the TIME ZONE button once to complete your new TIME ZONE
setting.
the Clock
Checking the Current Year/Date/Day of Week/Time Settings
Press briefly the TIME SET button repeatedly to see the cycle of
year, date, day of week (where d1, d2-d7 stand for Monday, Tuesday
to Sunday respectively) and time. To resume time display mode,
leave it idle for 5 secs.
the “TIME SET”
the button;
Press the "TIME SET" button again and release, the Month will flash.
Press the “▼” or “▲” button to adjust the Month.
Press the "TIME SET" button again and release, the Date will flash.
Press the “▼” or “▲” button to adjust the Date.
5
6
Press the "TIME SET" button again and release, the Hour will flash.
Press the “▼” or “▲” button to adjust the Hour.
Press the "TIME SET" button again and release, the Minutes will flash.
Press the “▼” or “▲” button to adjust the Minutes.
Press the “TIME SET” button again or leave it idle for 5 secs to store all
the settings, and resume to clock mode
7
8
9
10
11
。
AL1 AL2
DIM MER
LIG HT
TEM P.
AM
AL1
AL
2
Setting the Alarm(AL1 or AL2)
On or Off.
When the Alarm comes ON, press “SNOOZE” button to pause it for 9 minutes.
Alarm indicator will flash during Snooze Alarm mode.
Snooze Alarm will only be active for one hour. To turn off Snooze Alarm mode,
press the "AL1" ("AL2") button once.The Alarm indicator will then
become solid (to be On again same time next day).
10
12
4-
ER100104
ER100104-20180917-00
17
14
13
15
AM
AL1
AL2
Press the “TEMP.”button to sense indoor temperature in Fahrenheit (F)
or Celsius (C).
The temperature can be converted between Fahrenheit and Celsius by
pressing and holding the "TEMP." button while in temperature mode.
1
2
Sensing Room Temperature
AL1 AL2
DIMME R
LIGHT
TEMP.
AM
AL1
AL2
Celsius
Fahrenheit
AL1 AL2
DIM MER
LIG HT
TEM P.
AM
AL1
AL2
Qi Wireless Charging
16
AM
AL1
AL2
AL1 AL2
DIM MER
LIG HT
TEM P.
AM
AL1
AL2
AM
8
9
.
1
2
3
Smartphone/mobile device
Qi-enabled Receiver
Wireless Charging Pad
hold the
Press the “AL1” (“AL2”) button again, the Minutes will flash. Press the
“▼” or “▲” button to adjust the Minutes.
2
Press the
1.5d
6.7d
default
Press the
3
4
Press the AL1 (AL2) button again to save the Alarm settings and resume
clock mode.
5
Press the
When the AL1 (AL2) indicator lights On, Wake to Buzzer Alarm for
AL1 (AL2) will be On.
press the
repeatedly
the indicator for the AL1 (AL2) Wake to Buzzer
Alarm is Off.
Press the button indicated to turn On the LED for decorations.To turn it Off,
press the same button once.
Press the "DIMMER" button to set the clock display at one of the
4 brightness levels.
(if your smartphone
itself is not Qi-compatible)
An 5W Qi Wireless Charging Pad is built on top of this unit for wireless
power transfer to any Qi-compatible Smartphones or Qi-enabled
Receivers over a vertical distance of not more than 0.2 inches (5 mm).
Place your Qi-compatible Smartphone or Receiver (only one set at a
time) on top of the Wireless Charging Pad. The center of your
Smartphone or Receiver must be positioned properly right at the middle
of this charging pad in order to maximize the charging efficiency.
While wireless charging started or detected, the Qi indicator will be
flashing Red slowly.
While wireless charging error occurred (if metal sheet/substance
placed on top of the charging pad), the Qi indicator will be flashing Red
rapidly to alert user to get the erroneous receiver removed.
When your Smartphone is fully charged, the Qi indicator will turn solid
Green (except for iPhones).
4
The lithium backup battery needs replacement when the LOW BATTERY
indicator flashes, otherwise, the time and alarm settings will be lost/reset
after a power outage.
Leave the AC adapter connected to your AC outlet to retain memory while
the original battery is removed.
Unscrew the battery holder from the cabinet with a small screwdriver and
insert a new battery with the same CR2032 or equivalent type into the
holder the same way, observing the positive (+) polarity before sliding the
holder back into the slot. The LOW BATTERY indicator should then be Off.
polarity facing downward
  • Page 1 1
  • Page 2 2

Emerson ER100104 Wireless Charging Alarm Clock Owner's manual

Emerson
Brand
Emerson
Model
ER100104 Wireless Charging Alarm Clock
Category
Alarm clocks
Type
Owner's manual
This manual is also suitable for

Emerson ER100104 Wireless Charging Alarm Clock features a large LED display that shows time, date, and temperature. It has dual alarms that can be set independently, and both alarms can be programmed for everyday operation, weekdays only, or weekends only. The clock also has a snooze button and a dimmer switch to adjust the brightness of the display. On the top of the clock, there is a wireless charging pad that can be used to charge Qi-enabled devices such as smartphones and tablets.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents