Pyle PCJD50 Owner's manual

Brand: Pyle

Model: PCJD50

Type: Owner's manual

PCJD50

Hybrid Acoustic/Electronic Cajon

Stringed Cajon with Built-in Pickup Connector,

Internal Guitar Snare Strings

www.PyleUSA.com

1. Nail Socket: 6.35 mono pickup output socket, the socket

with the power switch, the power will be supplied auto

matically when the connector plug is inserted, the power

will automatically power’s OFF when unplugged.

2. Condenser Pickup Microphone: The microphone comes

with 3M glue at the bottom, and paste it inside of the drum

(as the installation drawing)

3. Battery: 9V battery is packed in the built-in strong 3M

rubber battery pack, and paste on the bottom of the drum.

4. Volume adjustment knob: Paste on the side of the sound

hole of the drum

Pickup installation steps:

1. The bottom left corner of the back board of the drum has a 12mm hole for nail.

2. Attach the microphone to the back panel of the drum, the distance from the sound hole edge can be adjusted

according to the timbre requirement of each drum.

3. Attach the volume control knob to the back panel of the drum, the knob should be higher than sound hole edge, it's

more convenient for adjusting the volume, clockwise to increase the volume, counter-clockwise to reduce the volume.

4. 9V battery is packed in the battery pack, 3M adhesive Velcro is attached to the bottom of the drum, near the back

panel.

5. Install the tail nail socket on the back board of the drum. (as picture below)

6. Tie the extra thread with a sticky buckle, paste to the back board, avoid noise caused by vibration when playing.

Back side of cajon

Left side of cajon

Condencer Microphone

12mm Nail socket

9V Battery pack

Tapping side of cajon

Volume adjustment knob

Right side of cajon

www.PyleUSA.com

Pickup installation steps:

1. Tail screw shell

2. Gasket

3. Length Adjusting nut

4. Gasket

5. Non-slip mat

6 . Gasket

7. Fixed nut

8. Straps cap

Installation points of tail nail:

1. Firstly make a 12mm hole then install the tail nail as shown in the photo above.

2. Remove the tail nail of number 6, 7, 8, and adjust the length of the tail nail of number 3.

3. Adjustment nut passes through the drilled hole, and the at large diameter of nail is exactly the same as the at of the

drum, insert about 1mm as the standard.

4. Too long will make the tail nail unstable, if the connector plug is not in position when used too short, there will be no

signal output.

Temporary use points

1. Put the 9V battery into the battery pack and button it well, the volume control

remains closed.

2. Attach the microphone in the back board of the drum, the distance from the sound

hole edge can be adjusted according to the timbre requirements of each drum.

3. 6.35 noise-canceling wire is inserted into tail nail socket, another side insert to the

speaker, and keep the volume control o.

4. Turn ON the power supply of the speaker, and turn on the volume control of the

speaker, when the volume is adjusted to an appropriate state, then you can start

playing.

Features:

• Hybrid Acoustic/Electronic Cajon

• Traditional Stringed Cajon Design

• Handcrafted Wooden Panel Box Frame

• Guitar Pick-Up Style 1/4’’ -inch Connector

• Acoustic Hand Percussion Instrument Tone Sounds

• Integrated Snare Strings for Rhythmic Production

• Anti-Vibration Interference Rubber-Capped Feet

• Lightweight and Compact Cajon Style

• Ability to Connect to External PA System, Amplier, Speaker System

• Musical Fun for All Ages!

What's in the Box:

• Electric Cajon • 9V Battery

• Pickup • Allen Key

Technical Specs:

• Cajon Type: Hybrid Electronic Style, Acoustic / e-Cajon

• Pickup Connector Type: 1/4’’ -inch (6.35mm) Jack

• Construction Material: Birch Wood

• Battery Operated Pickup, Requires (1) x ‘9V’ Battery (Included)

• Total Cajon Size (L x W x H): 13.4'' x 13.0'' x 20.1'' -inches

1 2 4 6 7 8

3 5

Pyle PCJD50 Owner's manual

Pyle PCJD50 Owner's manual

Pyle PCJD50 Owner's manual

Related papers

Other documents