Telit Communications S.p.A. GE864 DUAL V2 User manual

Type
User manual

This manual is also suitable for

GE
864
QUAD V2
and
GE864 DUAL V2
Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 2 of 73
APPLICABILITY TABLE
APPLICABILITY TABLEAPPLICABILITY TABLE
APPLICABILITY TABLE
PRODUCT
PRODUCTPRODUCT
PRODUCT
GE
GEGE
GE864
864864
864-
--
-QUAD
QUADQUAD
QUAD V2
V2 V2
V2
GE
GEGE
GE864
864864
864-
--
-DUAL V2
DUAL V2DUAL V2
DUAL V2
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 3 of 73
DISCLAIMER
DISCLAIMERDISCLAIMER
DISCLAIMER
The information contained in this document is the proprietary information of Telit
Communications S.p.A. and its affiliates (TELIT).
The contents are confidential and any disclosure to persons other than the officers,
employees, agents or subcontractors of the owner or licensee of this document,
without the prior written consent of Telit, is strictly prohibited.
Telit makes every effort to ensure the quality of the information it makes available.
Notwithstanding the foregoing, Telit does not make any warranty as to the
information contained herein, and does not accept any liability for any injury, loss or
damage of any kind incurred by use of or reliance upon the information.
Telit disclaims any and all responsibility for the application of the devices
characterized in this document, and notes that the application of the device must
comply with the safety standards of the applicable country, and where applicable,
with the relevant wiring rules.
Telit reserves the right to make modifications, additions and deletions to this
document due to typographical errors, inaccurate information, or improvements to
programs and/or equipment at any time and without notice.
Such changes will, nevertheless be incorporated into new editions of this document.
Copyright: Transmittal, reproduction, dissemination and/or editing of this document
as well as utilization of its contents and communication thereof to others without
express authorization are prohibited. Offenders will be held liable for payment of
damages. All rights are reserved.
Copyright © Telit Communications SpA 2010.©
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 4 of 73
Contents
ContentsContents
Contents
APPLICABILITY
TABLE .............................................................................................................................................. 2
1.
1.1.
1.
INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION ................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
.....................................
..........
.....6
66
6
1.1.
S
COPE
.................................................................................................................................................................. 6
1.2.
A
UDIENCE
............................................................................................................................................................. 6
1.3.
C
ONTACT
I
NFORMATION
,
S
UPPORT
........................................................................................................................ 6
1.4.
D
OCUMENT
O
RGANIZATION
.................................................................................................................................... 7
1.5.
T
EXT
C
ONVENTIONS
.............................................................................................................................................. 8
1.6.
R
ELATED
D
OCUMENTS
........................................................................................................................................... 8
1.7.
D
OCUMENT
H
ISTORY
............................................................................................................................................. 9
2.
2.2.
2.
OVERVIEW
OVERVIEWOVERVIEW
OVERVIEW ................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
............................................
........................
............ 10
1010
10
3.
3.3.
3.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL MECHANICAL DIME
DUAL MECHANICAL DIMEDUAL MECHANICAL DIME
DUAL MECHANICAL DIMENSIONS
NSIONSNSIONS
NSIONS................................
................................................................
.............................................................
..........................................................
............................. 11
1111
11
4.
4.4.
4.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 MODULE CONNE
DUAL V2 MODULE CONNEDUAL V2 MODULE CONNE
DUAL V2 MODULE CONNECTIONS
CTIONSCTIONS
CTIONS................................
................................................................
.............................................................
..........................................................
............................. 12
1212
12
4.1.
PIN-OUT........................................................................................................................................................... 12
4.1.1.
BGA Balls Layout..................................................................................................................................... 17
5.
5.5.
5.
HARDWARE COMMANDS
HARDWARE COMMANDSHARDWARE COMMANDS
HARDWARE COMMANDS................................
................................................................
................................................................
................................................................
................................................................
................................................................
.....................................................
..........................................
..................... 19
1919
19
5.1.
T
URNING
ON
THE
GE864-QUAD
V2
/
GE864-DUAL
V2................................................................................... 19
5.2.
T
URNING
OFF
THE
GE864-QUAD
V2
/
GE864-DUAL
V2 ................................................................................. 21
5.2.1.
Hardware Unconditional Restart
........................................................................................................ 22
6.
6.6.
6.
PO
POPO
POWER SUPPLY
WER SUPPLYWER SUPPLY
WER SUPPLY................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
...................................
......
... 24
2424
24
6.1.
P
OWER
S
UPPLY
R
EQUIREMENTS
......................................................................................................................... 24
6.2.
G
ENERAL
D
ESIGN
R
ULES
.................................................................................................................................... 25
6.2.1.
Electrical Design Guidelines
............................................................................................................... 25
6.2.2.
Thermal Design Guidelines
................................................................................................................. 29
6.2.3.
Power Supply PCB Layout Guidelines
................................................................................................ 30
6.2.4.
Parameters for ATEX Applications
.................................................................................................... 31
7.
7.7.
7.
ANTENNA
ANTENNAANTENNA
ANTENNA ................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
............................................
........................
............ 33
3333
33
7.1.
GSM
A
NTENNA
R
EQUIREMENTS
.......................................................................................................................... 33
7.2.
GSM
A
NTENNA
I
NSTALLATION
G
UIDELINES
...................................................................................................... 34
8.
8.8.
8.
LOGIC LEVEL SPECIFIC
LOGIC LEVEL SPECIFICLOGIC LEVEL SPECIFIC
LOGIC LEVEL SPECIFICATIONS
ATIONSATIONS
ATIONS ................................
................................................................
................................................................
................................................................
................................................................
................................................................
..........................................
....................
.......... 35
3535
35
8.1.
R
ESET
S
IGNAL
.................................................................................................................................................... 36
9.
9.9.
9.
SERIAL PORTS
SERIAL PORTSSERIAL PORTS
SERIAL PORTS................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
.....................................
..........
..... 37
3737
37
9.1.
MODEM
SERIAL
PORT.................................................................................................................................... 37
9.2.
RS232
L
EVEL
T
RANSLATION
............................................................................................................................. 39
9.3.
5V
UART
L
EVEL
T
RANSLATION
........................................................................................................................... 41
10.
10.10.
10.
AUDIO SECT
AUDIO SECTAUDIO SECT
AUDIO SECTION OVERVIEW
ION OVERVIEWION OVERVIEW
ION OVERVIEW ................................
................................................................
................................................................
................................................................
................................................................
................................................................
.............................................
..........................
............. 44
4444
44
10.1.
S
ELECTION MODE
............................................................................................................................................... 44
10.2.
E
LECTRICAL
C
HARACTERISTICS
........................................................................................................................ 46
10.2.1.
Input Lines Characteristics ...................................................................................................................... 46
10.2.2.
Output Lines Characteristics.................................................................................................................... 47
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 5 of 73
11.
11.11.
11.
GENERAL PURPOSE I/O
GENERAL PURPOSE I/OGENERAL PURPOSE I/O
GENERAL PURPOSE I/O ................................
................................................................
................................................................
................................................................
................................................................
................................................................
..................................................
....................................
.................. 49
4949
49
11.1.
GPIO
L
OGIC
L
EVELS
......................................................................................................................................... 50
11.2.
U
SING A
GPIO
P
AD AS
INPUT........................................................................................................................ 51
11.3.
U
SING A
GPIO
P
AD AS
OUTPUT .................................................................................................................... 51
11.4.
U
SING THE
RF
T
RANSMISSION
C
ONTROL
GPIO4.............................................................................................. 51
11.5.
U
SING THE
RFTXMON
O
UTPUT
GPIO5.......................................................................................................... 52
U
SING THE
A
LARM
O
UTPUT
GPIO6................................................................................................................................... 53
11.6.
U
SING THE
B
UZZER
O
UTPUT
GPIO7................................................................................................................ 53
11.7.
M
AGNETIC
B
UZZER
C
ONCEPTS
......................................................................................................................... 54
11.7.1.
Short Description
.................................................................................................................................. 54
11.8.1 Frequency Behavior
................................................................................................................................... 55
11.7.2.
Power Supply Influence
....................................................................................................................... 55
11.7.3.
Warning
.................................................................................................................................................. 55
11.7.4.
Working Current Influence
.................................................................................................................. 56
11.8.
U
SING THE
T
EMPERATURE
M
ONITOR
F
UNCTION
............................................................................................... 56
11.8.1.
Short Description
.................................................................................................................................. 56
11.8.2.
Allowed GPIO
......................................................................................................................................... 56
11.9.
I
NDICATION OF
N
ETWORK
S
ERVICE
A
VAILABILITY
............................................................................................. 57
11.10.
RTC
B
YPASS
O
UT
........................................................................................................................................... 58
11.11.
DAC
C
ONVERTER
............................................................................................................................................ 59
11.11.1.
Description
......................................................................................................................................... 59
11.11.2.
Enabling DAC
..................................................................................................................................... 59
11.11.3.
Low Pass Filter Example
................................................................................................................. 60
11.12.
ADC
C
ONVERTER
............................................................................................................................................ 60
11.12.1.
Description
......................................................................................................................................... 60
11.12.2.
Using ADC Converter
........................................................................................................................ 61
11.13.
D
EBUG OF THE
GE864-QUAD
V2
/
GE864-DUAL
V2
IN
P
RODUCTION
....................................................... 61
12.
12.12.
12.
ASSEMBLY THE GE864
ASSEMBLY THE GE864ASSEMBLY THE GE864
ASSEMBLY THE GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 ON THE BOARD
DUAL V2 ON THE BOARDDUAL V2 ON THE BOARD
DUAL V2 ON THE BOARD ................................
................................................................
.............................................
..........................
............. 62
6262
62
12.1.
R
ECOMMENDED FOOT PRINT FOR THE APPLICATION
.......................................................................................... 63
12.2.
S
TENCIL
............................................................................................................................................................. 63
12.3.
PCB
PAD DESIGN
............................................................................................................................................... 64
12.4.
S
OLDER PASTE
................................................................................................................................................... 65
12.4.1.
GE865 Solder reflow................................................................................................................................ 66
13.
13.13.
13.
PACKING SYSTEM
PACKING SYSTEMPACKING SYSTEM
PACKING SYSTEM................................
................................................................
................................................................
................................................................
................................................................
................................................................
............................................................
........................................................
............................ 68
6868
68
13.1.
M
OISTURE SENSIBILITY
...................................................................................................................................... 69
14.
14.14.
14.
CONFORMITY ASSESSMEN
CONFORMITY ASSESSMENCONFORMITY ASSESSMEN
CONFORMITY ASSESSMENT ISSUES
T ISSUEST ISSUES
T ISSUES ................................
................................................................
................................................................
................................................................
..............................................................
............................................................
..............................70
7070
70
15.
15.15.
15.
SAFETY RECOMMENDATIO
SAFETY RECOMMENDATIOSAFETY RECOMMENDATIO
SAFETY RECOMMENDATIONS
NSNS
NS ................................
................................................................
................................................................
................................................................
................................................................
................................................................
.........................................
..................
......... 72
7272
72
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 6 of 73
1. Introduction
1.1. Scope
The aim of this document is the description of some hardware solutions useful for
developing a product with the Telit GE864-QUAD V2 / GE864-DUAL V2 module.
1.2. Audience
This document is intended for Telit customers, who are integrators, about to
implement their applications using our GE864-QUAD V2 / GE864-DUAL V2 module.
1.3. Contact Information, Support
For general contact, technical support, to report documentation errors and to order
manuals, contact Telit Technical Support Center (TTSC) at:
TS-LATINAMERICA@telit.com
Alternatively, use:
http://www.telit.com/en/products/technical-support-center/contact.php
For detailed information about where you can buy the Telit modules or for
recommendations on accessories and components visit:
http://www.telit.com
To register for product news and announcements or for product questions contact
Telits Technical Support Center (TTSC).
Our aim is to make this guide as helpful as possible. Keep us informed of your
comments and suggestions for improvements.
Telit appreciates feedback from the users of our information.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 7 of 73
1.4. Document Organization
This document contains the following chapters:
Chapter 1: “Introduction” provides a scope for this document, target audience,
contact and support information, and text conventions.
Chapter 2: “Overview” provides an overview of the document.
Chapter 3: “GE864-QUAD V2 / GE864-DUAL V2 Mechanical Dimensions”
Chapter 4: “GE864-QUAD V2 / GE864-DUAL V2 Module Connections” deals with the
pin out configuration and layout.
Chapter 5: “Hardware Commands” How to control the module via hardware.
Chapter 6: “Power supply” Power supply requirements and general design rules.
Chapter 7: “Antenna” The antenna connection and board layout design are the most
important parts in the full product design
Chapter 8: “Logic Level specifications” Specific values adopted in the implementation
of logic levels for this module.
Chapter 9: “Serial ports” The serial port on the Telit GE864-QUAD V2 / GE864-DUAL
is the core of the interface between the module and OEM hardware
Chapter 10: “Audio Section overview” Refers to the audio blocks of the Base Band
Chip of the GE864-QUAD V2 / GE864-DUAL Telit Modules.
Chapter 11: “General Purpose I/O” How the general purpose I/O pads can be
configured.
Chapter 12 “DAC and ADC Section” Deals with these two kind of converters.
Chapter 13: Mounting the GE864-QUAD V2 / GE864-DUAL V2 on the application
board Recommendations and specifics on how to mount the module on the users
board.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 8 of 73
1.5. Text Conventions
Danger
Danger Danger
Danger
This information MUST be followed or catastrophic equipment failure
This information MUST be followed or catastrophic equipment failure This information MUST be followed or catastrophic equipment failure
This information MUST be followed or catastrophic equipment failure
or bodily injury may occur.
or bodily injury may occur.or bodily injury may occur.
or bodily injury may occur.
Caution or Warning
Caution or Warning Caution or Warning
Caution or Warning
Alerts the user to important points about integratin
Alerts the user to important points about integratin Alerts the user to important points about integratin
Alerts the user to important points about integrating the
g the g the
g the
module, if these points are not followed, the module and end user equipment
module, if these points are not followed, the module and end user equipment module, if these points are not followed, the module and end user equipment
module, if these points are not followed, the module and end user equipment
may fail or malfunction.
may fail or malfunction.may fail or malfunction.
may fail or malfunction.
Tip or Information
Tip or Information Tip or Information
Tip or Information Provides advice and suggestions that may be useful when
Provides advice and suggestions that may be useful when Provides advice and suggestions that may be useful when
Provides advice and suggestions that may be useful when
integrating the module.
integrating the module.integrating the module.
integrating the module.
All dates are in ISO 8601 format, i.e. YYYY-MM-DD.
1.6. Related Documents
Telit's GSM/GPRS Family Software User Guide, 1vv0300784
Audio settings application note , 80000NT10007a
Digital voice Interface Application Note, 80000NT10004a
Product description, 80331ST10074a
SIM Holder Design Guides, 80000NT10001a
AT Commands Reference Guide, 80000ST10025a
Telit EVK2 User Guide, 1vv0300704
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 9 of 73
1.7. Document History
R
RR
R
R
RR
R
e
ee
e
e
ee
e
v
vv
v
v
vv
v
i
ii
i
i
ii
i
s
ss
s
s
ss
s
i
ii
i
i
ii
i
o
oo
o
o
oo
o
n
nn
n
n
nn
n
D
DD
D
D
DD
D
a
aa
a
a
aa
a
t
tt
t
t
tt
t
e
ee
e
e
ee
e
C
CC
C
C
CC
C
h
hh
h
h
hh
h
a
aa
a
a
aa
a
n
nn
n
n
nn
n
g
gg
g
g
gg
g
e
ee
e
e
ee
e
s
ss
s
s
ss
s
ISSUE#0 2010-02-03 Release First ISSUE# 0
ISSUE#1 2010-03-29 Updated Par. 5.1, Par.6.1, Par.7.1, Par.9.2,
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 10 of 73
2. Overview
In this document all the basic functions of a mobile phone are taken into account; for
each one of them a proper hardware solution is suggested and eventually the wrong
solutions and common errors to be avoided are evidenced. Obviously this document
cannot embrace the whole hardware solutions and products that may be designed.
The wrong solutions to be avoided shall be considered as mandatory, while the
suggested hardware configurations shall not be considered mandatory, instead the
information given shall be used as a guide and a starting point for properly
developing your product with the Telit GE864-QUAD V2 / GE864-DUAL V2 module. For
further hardware details that may not be explained in this document refer to the Telit
GE864-QUAD V2 / GE864-DUAL V2 Product Description document where all the
hardware information is reported.
NOTICE
NOTICENOTICE
NOTICE:
::
:
(EN) The integration of the GSM/GPRS GE864-QUAD V2 / GE864-DUAL V2 cellular
module within user application shall be done according to the design rules described
in this manual.
The information presented in this document is believed to be accurate and reliable.
However, no responsibility is assumed by Telit Communications S.p.A. for its use, or
any infringement of patents or other rights of third parties which may result from its
use. No license is granted by implication or otherwise under any patent rights of Telit
Communications S.p.A. other than for circuitry embodied in Telit products. This
document is subject to change without notice.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 11 of 73
3. GE864-QUAD V2 / GE864-DUAL Mechanical
Dimensions
The Telit GE864-QUAD V2 / GE864-DUAL V2 module overall dimensions are:
Length: 30 mm
Width: 30 mm
Thickness: 2,9 mm
Weight: 4.2g
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 12 of 73
4. GE864-QUAD V2 / GE864-DUAL V2 Module Connections
4.1. PIN-OUT
The GE864-QUAD V2 / GE864-DUAL V2 uses 11x11 array BGA technology connection
Ball
BallBall
Ball
Signal
SignalSignal
Signal
I/O
I/OI/O
I/O
Function
FunctionFunction
Function
Internal
Internal Internal
Internal
PULL UP
PULL UPPULL UP
PULL UP
Type
TypeType
Type
Audio
AudioAudio
Audio
F9
F9F9
F9
AXE I Handsfree switching 100K CMOS 2.8V
G8
G8G8
G8
MIC_HF+ AI Handsfree mic. input; phase +, nom. level 3mVrms Audio
G9
G9G9
G9
MIC_MT- AI Handset mic.signal input; phase-, nom. level 50mVrms
Audio
G10
G10G10
G10
EAR_MT+ AO Handset earphone signal output, phase + Audio
J8
J8J8
J8
MIC_MT+ AI Handset mic.signal input; phase+, nom. level 50mVrms
Audio
J9
J9J9
J9
MIC_HF- AI Handsfree mic.input; phase -, nom. level 3mVrms Audio
J10
J10J10
J10
EAR_HF- AO Handsfree ear output, phase - Audio
H9
H9H9
H9
EAR_MT- AO Handset earphone signal output, phase - Audio
H10
H10H10
H10
EAR_HF+ AO Handsfree ear output, phase + Audio
SIM card interface
SIM card interfaceSIM card interface
SIM card interface
C10
C10C10
C10
SIMCLK O External SIM signal – Clock 1,8 / 3V
C11
C11C11
C11
SIMIN I External SIM signal - Presence (active low)
Pull up 47K
1,8 / 3V
D4
D4D4
D4
SIMVCC - External SIM signal – Power supply for the SIM 1,8 / 3V
D10
D10D10
D10
SIMIO I/O External SIM signal - Data I/O
Pull up
4.7K
1,8 / 3V
E9
E9E9
E9
SIMRST O External SIM signal – Reset 1,8 / 3V
Trace
TraceTrace
Trace
D11
D11D11
D11
TX_TRACE O TX Data for debug monitor CMOS 2.8V
F10
F10F10
F10
RX_TRACE I RX Data for debug monitor CMOS 2.8V
H4
H4H4
H4
SERVICE I
Service pin shall be used to upgrade the module
from ASC1 (RX_TRACE, TX_TRACE). The pin
shall be tied low to enable the feature only in
case of a SW Update activity. It is required, for
debug purpose, to be connected
to a test pad on the final application.
CMOS 2.8V
Prog. / Data + HW Flow Control
Prog. / Data + HW Flow ControlProg. / Data + HW Flow Control
Prog. / Data + HW Flow Control
B6
B6B6
B6
C125/RING O Output for Ring indicator signal (RI) to DTE CMOS 2.8V
B7
B7B7
B7
C108/DTR I Input for Data terminal ready signal (DTR) from DTE CMOS 2.8V
D9
D9D9
D9
C109/DCD O Output for Data carrier detect signal (DCD) to DTE CMOS 2.8V
E7
E7E7
E7
C103/TXD I Serial data input (TXD) from DTE CMOS 2.8V
E11
E11E11
E11
C107/DSR O Output for Data set ready signal (DSR) to DTE CMOS 2.8V
F7
F7F7
F7
C105/RTS I Input for Request to send signal (RTS) from DTE CMOS 2.8V
F6
F6F6
F6
C106/CTS O Output for Clear to send signal (CTS) to DTE CMOS 2.8V
H8
H8H8
H8
C104/RXD O Serial data output to DTE CMOS 2.8V
DA
DADA
DAC and ADC
C and ADCC and ADC
C and ADC
C7
C7C7
C7
DAC_OUT AO Digital/Analog converter output D/A
J11
J11J11
J11
ADC_IN1 AI Analog/Digital converter input A/D
H11
H11H11
H11
ADC_IN2 AI Analog/Digital converter input A/D
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 13 of 73
Ball
BallBall
Ball
Signal
SignalSignal
Signal
I/O
I/OI/O
I/O
Function
FunctionFunction
Function
Internal
Internal Internal
Internal
PULL UP
PULL UPPULL UP
PULL UP
Type
TypeType
Type
Miscellaneous Functions
Miscellaneous FunctionsMiscellaneous Functions
Miscellaneous Functions
A2
A2A2
A2
RESET* I Reset input
D8
D8D8
D8
STAT_LED O Status indicator led CMOS 1.8V
E2
E2E2
E2
VRTC AO VRTC Power
J5
J5J5
J5
ON_OFF* I
Input command for switching power ON or OFF (toggle
command). The pulse to be sent to the GE864-QUAD V2
must be equal or greater than 1 second.
Pull up 47K
Pull up to VBATT
L8
L8L8
L8
PWRMON I/O PWRMON CMOS 2.8V
L4
L4L4
L4
GSM Antenna O Antenna output – 50 ohm RF
Telit GPIO
Telit GPIOTelit GPIO
Telit GPIO / DVI
/ DVI / DVI
/ DVI
C1
C1C1
C1
GPIO_01 I/O GPIO_01 CMOS 2.8V
E6
E6E6
E6
GPIO_02 / JDR I/O GPIO_02 / JDR CMOS 2.8V
C2
C2C2
C2
GPIO_03 I/O GPIO_03 CMOS 2.8V
B3
B3B3
B3
GPIO_04 / TX_DISABLE I/O GPIO_04 / TX_DISABLE CMOS 2.8V
K8
K8K8
K8
GPIO_05 / RFTXMON I/O
Telit GPIO05 Configurable GPIO / Transmitter ON
monitor
CMOS 2.8V
B5
B5B5
B5
GPIO_06 / ALARM I/O Telit GPIO06 Configurable GPIO / ALARM CMOS 2.8V
L9
L9L9
L9
GPIO_07 / BUZZER I/O Telit GPIO07 Configurable GPIO / Buzzer CMOS 2.8V
K11
K11K11
K11
GPIO_08 I/O GPIO_08 CMOS 2.8V
C9
C9C9
C9
GPIO_09 I/O GPIO_09 CMOS 2.8V
H3
H3H3
H3
GPIO_10 / DVI_TX I/O GPIO_10 / DVI_TX CMOS 2.8V
K7
K7K7
K7
DVI_RX I/O DVI_RX CMOS 2.8V
D7
D7D7
D7
DVI_CLK I/O DVI_CLK CMOS 2.8V
H5
H5H5
H5
DVI_WA0 I/O DVI_WA0 CMOS 2.8V
Power Supply
Power SupplyPower Supply
Power Supply
J1
J1J1
J1
VBATT - Main power supply Power
K1
K1K1
K1
VBATT - Main power supply Power
J2
J2J2
J2
VBATT - Main power supply Power
K2
K2K2
K2
VBATT - Main power supply Power
A1
A1A1
A1
GND - Ground Power
A11
A11A11
A11
GND - Ground Power
D6
D6D6
D6
GND - Ground Power
F1
F1F1
F1
GND - Ground Power
F11
F11F11
F11
GND - Ground Power
H
HH
H1
11
1
GND - Ground Power
H2
H2H2
H2
GND - Ground Power
J3
J3J3
J3
GND - Ground Power
K3
K3K3
K3
GND - Ground Power
K4
K4K4
K4
GND - Ground Power
K5
K5K5
K5
GND - Ground Power
K6
K6K6
K6
GND - Ground Power
L1
L1L1
L1
GND - Ground Power
L2
L2L2
L2
GND - Ground Power
L3
L3L3
L3
GND - Ground Power
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 14 of 73
Ball
BallBall
Ball
Signal
SignalSignal
Signal
I/O
I/OI/O
I/O
Function
FunctionFunction
Function
Internal
Internal Internal
Internal
PULL UP
PULL UPPULL UP
PULL UP
Type
TypeType
Type
L6
L6L6
L6
GND - Ground Power
L11
L11L11
L11
GND - Ground Power
RESERVED
RESERVEDRESERVED
RESERVED
A3
A3A3
A3
- - Reserved
A4
A4A4
A4
- - Reserved
A5
A5A5
A5
- - Reserved
A6
A6A6
A6
- - Reserved
A7
A7A7
A7
- - Reserved
A8
A8A8
A8
- - Reserved
A9
A9A9
A9
- - Reserved
A10
A10A10
A10
- - Reserved
B1
B1B1
B1
- - Reserved
B2
B2B2
B2
- - Reserved
B4
B4B4
B4
- - Reserved
B8
B8B8
B8
- - Reserved
B9
B9B9
B9
- - Reserved
B10
B10B10
B10
- - Reserved
B11
B11B11
B11
- - Reserved
C3
C3C3
C3
- - Reserved
C4
C4C4
C4
- - Reserved
C5
C5C5
C5
- - Reserved
C6
C6C6
C6
- - Reserved
C8
C8C8
C8
- - Reserved
D1
D1D1
D1
- - Reserved
D2
D2D2
D2
- - Reserved
D3
D3D3
D3
- - Reserved
D5
D5D5
D5
- - Reserved
E1
E1E1
E1
- - Reserved
E3
E3E3
E3
- - Reserved
E4
E4E4
E4
- - Reserved
E5
E5E5
E5
- - Reserved
E8
E8E8
E8
- - Reserved
E10
E10E10
E10
- - Reserved
F2
F2F2
F2
- - Reserved
F3
F3F3
F3
- - Reserved
F4
F4F4
F4
- - Reserved
F5
F5F5
F5
- - Reserved
F8
F8F8
F8
- - Reserved
G1
G1G1
G1
- - Reserved
G2
G2G2
G2
- -
Reserved
G3
G3G3
G3
- - Reserved
G4
G4G4
G4
- - Reserved
G5
G5G5
G5
- - Reserved
G6
G6G6
G6
- - Reserved
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 15 of 73
Ball
BallBall
Ball
Signal
SignalSignal
Signal
I/O
I/OI/O
I/O
Function
FunctionFunction
Function
Internal
Internal Internal
Internal
PULL UP
PULL UPPULL UP
PULL UP
Type
TypeType
Type
G7
G7G7
G7
- - Reserved
G11
G11G11
G11
- - Reserved
H6
H6H6
H6
- - Reserved
H7
H7H7
H7
- - Reserved
J4
J4J4
J4
- - Reserved
J6
J6J6
J6
- -
Reserved
J7
J7J7
J7
- - Reserved
K9
K9K9
K9
- - Reserved
K10
K10K10
K10
- - Reserved
L5
L5L5
L5
- - Reserved
L7
L7L7
L7
- - Reserved
L10
L10L10
L10
- - Reserved
NOTE:
NOTE:NOTE:
NOTE:
The GE864-QUAD V2 / GE864-DUAL V2 Modules has only one DVI ports on the system
interface.
NOTE:
NOTE:NOTE:
NOTE:
Reserved pins must not be connected.
NOTE:
NOTE:NOTE:
NOTE:
RTS must be connected to the GND (on the module side) if flow control is not used.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 16 of 73
NOTE
NOTENOTE
NOTE:
::
:
If not used, almost all pins must be left disconnected. The only exceptions are the
following pins:
Ball
BallBall
Ball
Signal
SignalSignal
Signal
Function
FunctionFunction
Function
J
JJ
J1
11
1, J
, J, J
, J2
22
2, K1, K2
, K1, K2, K1, K2
, K1, K2
VBATT Main power supply
A1, A11, D6, F1, F11, H1,
A1, A11, D6, F1, F11, H1, A1, A11, D6, F1, F11, H1,
A1, A11, D6, F1, F11, H1,
H2, J3, K3, K4, K5
H2, J3, K3, K4, K5H2, J3, K3, K4, K5
H2, J3, K3, K4, K5, K6, L1,
, K6, L1, , K6, L1,
, K6, L1,
L2, L3, L6, L11
L2, L3, L6, L11L2, L3, L6, L11
L2, L3, L6, L11
GND Ground
E7
E7E7
E7
C103/TXD Serial data input (TXD) from DTE
H8
H8H8
H8
C104/RXD Serial data output to DTE
F7
F7F7
F7
C105/RTS Input for Request to send signal (RTS) from DTE
J5
J5J5
J5
ON/OFF* Input command for switching power ON or OFF (toggle command).
A2
A2A2
A2
RESET* Reset input
F10
F10F10
F10
RX_TRACE RX Data for debug monitor
D11
D11D11
D11
TX_TRACE TX Data for debug monitor
H4
H4H4
H4
SERVICE SERVICE connection
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 17 of 73
4.1.1.
4.1.1.4.1.1.
4.1.1. BGA Balls Layout
BGA Balls LayoutBGA Balls Layout
BGA Balls Layout
TOP VIEW
TOP VIEWTOP VIEW
TOP VIEW
A
AA
A
B
BB
B
C
CC
C
D
DD
D
E
EE
E
F
FF
F
G
GG
G
H
HH
H
J
JJ
J
K
KK
K
L
LL
L
1
11
1
GND - GPIO_01 - - GND - GND VBATT VBATT GND
2
22
2
RESET* - GPIO_03 - VRTC - - GND VBATT VBATT GND
3
33
3
-
GPIO_04 /
TX_DISABL
E
- - - _ -
GPIO_10 /
DVI_TX
GND GND GND
4
44
4
-- - - SIMVCC - - - SERVICE - GND
GSM
Antenna
5
55
5
-
GPIO_06 /
ALARM
- - - - -
DVI_WA0
ON_OFF* GND -
6
66
6
-
C125/RING
- GND
GPIO_02 /
JDR
C106 / CTS
- - - GND GND
7
77
7
- C108 / DTR
DAC_OUT DVI_CLK C103 / TXD
C105 / RTS
- - - DVI_RX -
8
88
8
- - - STAD_ LED
- - MIC_HF+ C104 / RXD
MIC_MT+
GPIO_05 /
RFTXMON
PWRMON
9
99
9
- - GPIO_09 C109 / DCD
SIMRST AXE MIC_MT- EAR_MT- MIC_HF- -
GPIO_07 /
BUZZER
10
1010
10
- - SIMCLK SIMIO
- RX_TRACE
EAR_MT+ EAR_HF+ EAR_HF- - -
11
1111
11
GND - SIMIN
TX_TRACE
C107 / DSR
GND - ADC_IN2 ADC_IN1 GPIO_08 GND
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 18 of 73
AUDIO Signals balls
SIM CARD interface balls
TRACE Signals balls
Prog. / data + Hw Flow Control signals balls
ADC signals balls
MISCELLANEOUS functions signals balls
TELIT GPIO balls
POWER SUPPLY VBATT balls
POWER SUPPLY GND balls
RESERVED
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 19 of 73
5. Hardware Commands
5.1. Turning ON the GE864-QUAD V2 / GE864-DUAL V2
To turn the GE864-QUAD V2 / GE864-DUAL V2 on, the pad ON# must be tied low for
at least 1000ms and then released. A pulse duration less than 1000ms should also
start the power on procedure, but this is not guaranteed.
The maximum current that can be drained from the ON# pad is 0,1 mA.
A simple circuit to do it is:
TIP:
TIP:TIP:
TIP:
To check if the device has powered on, the hardware line PWRMON must be
monitored. After 1000ms the line raised up the device could be considered powered
on.
NOTE:
NOTE:NOTE:
NOTE:
Do not use any pull up resistor on the ON# line, it is internally pulled up. Using pull
up resistor may bring to latch up problems on the GE864-QUAD V2 / GE864-DUAL V2
power regulator and improper power on/off of the module. The line ON# must be
connected only in open collector configuration.
In this document all the lines that are inverted, hence have active low signals are
labeled with a name that ends with a "#" or with a bar over the name.
NOTE
NOTENOTE
NOTE: When the power supply voltage is lower than 3.4V, to turn ON the module, the
pad ON# must be tied low for at least 3 seconds.
GE864
GE864GE864
GE864-
--
-QUAD V2 / GE864
QUAD V2 / GE864QUAD V2 / GE864
QUAD V2 / GE864-
--
-DUAL V2 Hardware User Guide
DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide
DUAL V2 Hardware User Guide
1vv0300875 Rev.1 – 2010-03-29
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved. Page 20 of 73
For example:
1- Let us assume you need to drive the ON# pad with a totem pole output of a +3/5 V
microcontroller (uP_OUT1):
2- Let us assume you need to drive the ON# pad directly with an ON/OFF button:
A flow chart with proper turn on procedure is detailed below:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73

Telit Communications S.p.A. GE864 DUAL V2 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI