Telit Communications S.p.A. RI7GE864Q2B User manual

GE

864

QUAD V2

and

GE864 DUAL V2

Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

APPLICABILITY TABLE

APPLICABILITY TABLEAPPLICABILITY TABLE

APPLICABILITY TABLE

PRODUCT

PRODUCTPRODUCT

PRODUCT

GE

GEGE

GE864

864864

864-

--

-QUAD

QUADQUAD

QUAD V2

V2 V2

V2

GE

GEGE

GE864

864864

864-

--

-DUAL V2

DUAL V2DUAL V2

DUAL V2

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

DISCLAIMER

DISCLAIMERDISCLAIMER

DISCLAIMER

The information contained in this document is the proprietary information of Telit

Communications S.p.A. and its affiliates (“TELIT”).

The contents are confidential and any disclosure to persons other than the officers,

employees, agents or subcontractors of the owner or licensee of this document,

without the prior written consent of Telit, is strictly prohibited.

Telit makes every effort to ensure the quality of the information it makes available.

Notwithstanding the foregoing, Telit does not make any warranty as to the

information contained herein, and does not accept any liability for any injury, loss or

damage of any kind incurred by use of or reliance upon the information.

Telit disclaims any and all responsibility for the application of the devices

characterized in this document, and notes that the application of the device must

comply with the safety standards of the applicable country, and where applicable,

with the relevant wiring rules.

Telit reserves the right to make modifications, additions and deletions to this

document due to typographical errors, inaccurate information, or improvements to

programs and/or equipment at any time and without notice.

Such changes will, nevertheless be incorporated into new editions of this document.

Copyright: Transmittal, reproduction, dissemination and/or editing of this document

as well as utilization of its contents and communication thereof to others without

express authorization are prohibited. Offenders will be held liable for payment of

damages. All rights are reserved.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

Contents

ContentsContents

Contents

APPLICABILITY

TABLE .............................................................................................................................................. 2

1.

1.1.

1.

INTRODUCTION

INTRODUCTIONINTRODUCTION

INTRODUCTION ................................

................................................................

.....................................

..........

.....6

66

6

1.1.

S

COPE

.................................................................................................................................................................. 6

1.2.

A

UDIENCE

............................................................................................................................................................. 6

1.3.

C

ONTACT

I

NFORMATION

,

S

UPPORT

........................................................................................................................ 6

1.4.

D

OCUMENT

O

RGANIZATION

.................................................................................................................................... 7

1.5.

T

EXT

C

ONVENTIONS

.............................................................................................................................................. 8

1.6.

R

ELATED

D

OCUMENTS

........................................................................................................................................... 8

1.7.

D

OCUMENT

H

ISTORY

............................................................................................................................................. 9

2.

2.2.

2.

OVERVIEW

OVERVIEWOVERVIEW

OVERVIEW ................................

................................................................

............................................

........................

............ 10

1010

10

3.

3.3.

3.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL MECHANICAL DIME

DUAL MECHANICAL DIMEDUAL MECHANICAL DIME

DUAL MECHANICAL DIMENSIONS

NSIONSNSIONS

NSIONS................................

................................................................

.............................................................

..........................................................

............................. 11

1111

11

4.

4.4.

4.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 MODULE CONNE

DUAL V2 MODULE CONNEDUAL V2 MODULE CONNE

DUAL V2 MODULE CONNECTIONS

CTIONSCTIONS

CTIONS................................

................................................................

.............................................................

..........................................................

............................. 12

1212

12

4.1.

PIN-OUT........................................................................................................................................................... 12

4.1.1.

BGA Balls Layout..................................................................................................................................... 17

5.

5.5.

5.

HARDWARE COMMANDS

HARDWARE COMMANDSHARDWARE COMMANDS

HARDWARE COMMANDS................................

................................................................

.....................................................

..........................................

..................... 19

1919

19

5.1.

T

URNING

ON

THE

GE864-QUAD

V2

/

GE864-DUAL

V2................................................................................... 19

5.2.

T

URNING

OFF

THE

GE864-QUAD

V2

/

GE864-DUAL

V2 ................................................................................. 21

5.2.1.

Hardware Unconditional Restart

........................................................................................................ 22

6.

6.6.

6.

PO

POPO

POWER SUPPLY

WER SUPPLYWER SUPPLY

WER SUPPLY................................

................................................................

...................................

......

... 24

2424

24

6.1.

P

OWER

S

UPPLY

R

EQUIREMENTS

......................................................................................................................... 24

6.2.

G

ENERAL

D

ESIGN

R

ULES

.................................................................................................................................... 25

6.2.1.

Electrical Design Guidelines

............................................................................................................... 25

6.2.2.

Thermal Design Guidelines

................................................................................................................. 29

6.2.3.

Power Supply PCB Layout Guidelines

................................................................................................ 30

6.2.4.

Parameters for ATEX Applications

.................................................................................................... 31

7.

7.7.

7.

ANTENNA

ANTENNAANTENNA

ANTENNA ................................

................................................................

............................................

........................

............ 33

3333

33

7.1.

GSM

A

NTENNA

R

EQUIREMENTS

.......................................................................................................................... 33

7.2.

GSM

A

NTENNA

–

I

NSTALLATION

G

UIDELINES

...................................................................................................... 34

8.

8.8.

8.

LOGIC LEVEL SPECIFIC

LOGIC LEVEL SPECIFICLOGIC LEVEL SPECIFIC

LOGIC LEVEL SPECIFICATIONS

ATIONSATIONS

ATIONS ................................

................................................................

..........................................

....................

.......... 35

3535

35

8.1.

R

ESET

S

IGNAL

.................................................................................................................................................... 36

9.

9.9.

9.

SERIAL PORTS

SERIAL PORTSSERIAL PORTS

SERIAL PORTS................................

................................................................

.....................................

..........

..... 37

3737

37

9.1.

MODEM

SERIAL

PORT.................................................................................................................................... 37

9.2.

RS232

L

EVEL

T

RANSLATION

............................................................................................................................. 39

9.3.

5V

UART

L

EVEL

T

RANSLATION

........................................................................................................................... 41

10.

10.10.

10.

AUDIO SECT

AUDIO SECTAUDIO SECT

AUDIO SECTION OVERVIEW

ION OVERVIEWION OVERVIEW

ION OVERVIEW ................................

................................................................

.............................................

..........................

............. 44

4444

44

10.1.

S

ELECTION MODE

............................................................................................................................................... 44

10.2.

E

LECTRICAL

C

HARACTERISTICS

........................................................................................................................ 46

10.2.1.

Input Lines Characteristics ...................................................................................................................... 46

10.2.2.

Output Lines Characteristics.................................................................................................................... 47

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

11.

11.11.

11.

GENERAL PURPOSE I/O

GENERAL PURPOSE I/OGENERAL PURPOSE I/O

GENERAL PURPOSE I/O ................................

................................................................

..................................................

....................................

.................. 49

4949

49

11.1.

GPIO

L

OGIC

L

EVELS

......................................................................................................................................... 50

11.2.

U

SING A

GPIO

P

AD AS

INPUT........................................................................................................................ 51

11.3.

U

SING A

GPIO

P

AD AS

OUTPUT .................................................................................................................... 51

11.4.

U

SING THE

RF

T

RANSMISSION

C

ONTROL

GPIO4.............................................................................................. 51

11.5.

U

SING THE

RFTXMON

O

UTPUT

GPIO5.......................................................................................................... 52

U

SING THE

A

LARM

O

UTPUT

GPIO6................................................................................................................................... 53

11.6.

U

SING THE

B

UZZER

O

UTPUT

GPIO7................................................................................................................ 53

11.7.

M

AGNETIC

B

UZZER

C

ONCEPTS

......................................................................................................................... 54

11.7.1.

Short Description

.................................................................................................................................. 54

11.8.1 Frequency Behavior

................................................................................................................................... 55

11.7.2.

Power Supply Influence

....................................................................................................................... 55

11.7.3.

Warning

.................................................................................................................................................. 55

11.7.4.

Working Current Influence

.................................................................................................................. 56

11.8.

U

SING THE

T

EMPERATURE

M

ONITOR

F

UNCTION

............................................................................................... 56

11.8.1.

Short Description

.................................................................................................................................. 56

11.8.2.

Allowed GPIO

......................................................................................................................................... 56

11.9.

I

NDICATION OF

N

ETWORK

S

ERVICE

A

VAILABILITY

............................................................................................. 57

11.10.

RTC

B

YPASS

O

UT

........................................................................................................................................... 58

11.11.

DAC

C

ONVERTER

............................................................................................................................................ 59

11.11.1.

Description

......................................................................................................................................... 59

11.11.2.

Enabling DAC

..................................................................................................................................... 59

11.11.3.

Low Pass Filter Example

................................................................................................................. 60

11.12.

ADC

C

ONVERTER

............................................................................................................................................ 60

11.12.1.

Description

......................................................................................................................................... 60

11.12.2.

Using ADC Converter

........................................................................................................................ 61

11.13.

D

EBUG OF THE

GE864-QUAD

V2

/

GE864-DUAL

V2

IN

P

RODUCTION

....................................................... 61

12.

12.12.

12.

ASSEMBLY THE GE864

ASSEMBLY THE GE864ASSEMBLY THE GE864

ASSEMBLY THE GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 ON THE BOARD

DUAL V2 ON THE BOARDDUAL V2 ON THE BOARD

DUAL V2 ON THE BOARD ................................

................................................................

.............................................

..........................

............. 62

6262

62

12.1.

R

ECOMMENDED FOOT PRINT FOR THE APPLICATION

.......................................................................................... 63

12.2.

S

TENCIL

............................................................................................................................................................. 63

12.3.

PCB

PAD DESIGN

............................................................................................................................................... 64

12.4.

S

OLDER PASTE

................................................................................................................................................... 65

12.4.1.

GE865 Solder reflow................................................................................................................................ 66

13.

13.13.

13.

PACKING SYSTEM

PACKING SYSTEMPACKING SYSTEM

PACKING SYSTEM................................

................................................................

............................................................

........................................................

............................ 68

6868

68

13.1.

M

OISTURE SENSIBILITY

...................................................................................................................................... 69

14.

14.14.

14.

CONFORMITY ASSESSMEN

CONFORMITY ASSESSMENCONFORMITY ASSESSMEN

CONFORMITY ASSESSMENT ISSUES

T ISSUEST ISSUES

T ISSUES ................................

................................................................

..............................................................

............................................................

..............................70

7070

70

15.

15.15.

15.

SAFETY RECOMMENDATIO

SAFETY RECOMMENDATIOSAFETY RECOMMENDATIO

SAFETY RECOMMENDATIONS

NSNS

NS ................................

................................................................

.........................................

..................

......... 72

7272

72

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

1. Introduction

1.1. Scope

The aim of this document is the description of some hardware solutions useful for

developing a product with the Telit GE864-QUAD V2 / GE864-DUAL V2 module.

1.2. Audience

This document is intended for Telit customers, who are integrators, about to

implement their applications using our GE864-QUAD V2 / GE864-DUAL V2 module.

1.3. Contact Information, Support

For general contact, technical support, to report documentation errors and to order

manuals, contact Telit Technical Support Center (TTSC) at:

[email protected]

TS-LATINAMERICA@telit.com

[email protected]

Alternatively, use:

http://www.telit.com/en/products/technical-support-center/contact.php

For detailed information about where you can buy the Telit modules or for

recommendations on accessories and components visit:

http://www.telit.com

To register for product news and announcements or for product questions contact

Telit’s Technical Support Center (TTSC).

Our aim is to make this guide as helpful as possible. Keep us informed of your

comments and suggestions for improvements.

Telit appreciates feedback from the users of our information.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

1.4. Document Organization

This document contains the following chapters:

Chapter 1: “Introduction” provides a scope for this document, target audience,

contact and support information, and text conventions.

Chapter 2: “Overview” provides an overview of the document.

Chapter 3: “GE864-QUAD V2 / GE864-DUAL V2 Mechanical Dimensions”

Chapter 4: “GE864-QUAD V2 / GE864-DUAL V2 Module Connections” deals with the

pin out configuration and layout.

Chapter 5: “Hardware Commands” How to control the module via hardware.

Chapter 6: “Power supply” Power supply requirements and general design rules.

Chapter 7: “Antenna” The antenna connection and board layout design are the most

important parts in the full product design

Chapter 8: “Logic Level specifications” Specific values adopted in the implementation

of logic levels for this module.

Chapter 9: “Serial ports” The serial port on the Telit GE864-QUAD V2 / GE864-DUAL

is the core of the interface between the module and OEM hardware

Chapter 10: “Audio Section overview” Refers to the audio blocks of the Base Band

Chip of the GE864-QUAD V2 / GE864-DUAL Telit Modules.

Chapter 11: “General Purpose I/O” How the general purpose I/O pads can be

configured.

Chapter 12 “DAC and ADC Section” Deals with these two kind of converters.

Chapter 13: “Mounting the GE864-QUAD V2 / GE864-DUAL V2 on the application

board” Recommendations and specifics on how to mount the module on the user’s

board.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

1.5. Text Conventions

Danger

Danger Danger

Danger

–

This information MUST be followed or catastrophic equipment failure

This information MUST be followed or catastrophic equipment failure This information MUST be followed or catastrophic equipment failure

This information MUST be followed or catastrophic equipment failure

or bodily injury may occur.

or bodily injury may occur.or bodily injury may occur.

or bodily injury may occur.

Caution or Warning

Caution or Warning Caution or Warning

Caution or Warning

–

Alerts the user to important points about integratin

Alerts the user to important points about integratin Alerts the user to important points about integratin

Alerts the user to important points about integrating the

g the g the

g the

module, if these points are not followed, the module and end user equipment

module, if these points are not followed, the module and end user equipment module, if these points are not followed, the module and end user equipment

module, if these points are not followed, the module and end user equipment

may fail or malfunction.

may fail or malfunction.may fail or malfunction.

may fail or malfunction.

Tip or Information

Tip or Information Tip or Information

Tip or Information – Provides advice and suggestions that may be useful when

Provides advice and suggestions that may be useful when Provides advice and suggestions that may be useful when

Provides advice and suggestions that may be useful when

integrating the module.

integrating the module.integrating the module.

integrating the module.

All dates are in ISO 8601 format, i.e. YYYY-MM-DD.

1.6. Related Documents

• Telit's GSM/GPRS Family Software User Guide, 1vv0300784

• Audio settings application note , 80000NT10007a

• Digital voice Interface Application Note, 80000NT10004a

• Product description, 80331ST10074a

• SIM Holder Design Guides, 80000NT10001a

• AT Commands Reference Guide, 80000ST10025a

• Telit EVK2 User Guide, 1vv0300704

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

1.7. Document History

R

RR

R

RR

R

e

ee

e

ee

e

v

vv

v

vv

v

i

ii

i

ii

i

s

ss

s

ss

s

i

ii

i

ii

i

o

oo

o

oo

o

n

nn

n

nn

n

D

DD

D

DD

D

a

aa

a

aa

a

t

tt

t

tt

t

e

ee

e

ee

e

C

CC

C

CC

C

h

hh

h

hh

h

a

aa

a

aa

a

n

nn

n

nn

n

g

gg

g

gg

g

e

ee

e

ee

e

s

ss

s

ss

s

ISSUE#0 2010-02-03 Release First ISSUE# 0

ISSUE#1 2010-03-29 Updated Par. 5.1, Par.6.1, Par.7.1, Par.9.2,

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

2. Overview

In this document all the basic functions of a mobile phone are taken into account; for

each one of them a proper hardware solution is suggested and eventually the wrong

solutions and common errors to be avoided are evidenced. Obviously this document

cannot embrace the whole hardware solutions and products that may be designed.

The wrong solutions to be avoided shall be considered as mandatory, while the

suggested hardware configurations shall not be considered mandatory, instead the

information given shall be used as a guide and a starting point for properly

developing your product with the Telit GE864-QUAD V2 / GE864-DUAL V2 module. For

further hardware details that may not be explained in this document refer to the Telit

GE864-QUAD V2 / GE864-DUAL V2 Product Description document where all the

hardware information is reported.

NOTICE

NOTICENOTICE

NOTICE:

::

:

(EN) The integration of the GSM/GPRS GE864-QUAD V2 / GE864-DUAL V2 cellular

module within user application shall be done according to the design rules described

in this manual.

The information presented in this document is believed to be accurate and reliable.

However, no responsibility is assumed by Telit Communications S.p.A. for its use, or

any infringement of patents or other rights of third parties which may result from its

use. No license is granted by implication or otherwise under any patent rights of Telit

Communications S.p.A. other than for circuitry embodied in Telit products. This

document is subject to change without notice.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

3. GE864-QUAD V2 / GE864-DUAL Mechanical

Dimensions

The Telit GE864-QUAD V2 / GE864-DUAL V2 module overall dimensions are:

• Length: 30 mm

• Width: 30 mm

• Thickness: 2,9 mm

• Weight: 4.2g

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

4. GE864-QUAD V2 / GE864-DUAL V2 Module Connections

4.1. PIN-OUT

The GE864-QUAD V2 / GE864-DUAL V2 uses 11x11 array BGA technology connection

Ball

BallBall

Ball

Signal

SignalSignal

Signal

I/O

I/OI/O

I/O

Function

FunctionFunction

Function

Internal

Internal Internal

Internal

PULL UP

PULL UPPULL UP

PULL UP

Type

TypeType

Type

Audio

AudioAudio

Audio

F9

F9F9

F9

AXE I Handsfree switching 100K CMOS 2.8V

G8

G8G8

G8

MIC_HF+ AI Handsfree mic. input; phase +, nom. level 3mVrms Audio

G9

G9G9

G9

MIC_MT- AI Handset mic.signal input; phase-, nom. level 50mVrms

Audio

G10

G10G10

G10

EAR_MT+ AO Handset earphone signal output, phase + Audio

J8

J8J8

J8

MIC_MT+ AI Handset mic.signal input; phase+, nom. level 50mVrms

Audio

J9

J9J9

J9

MIC_HF- AI Handsfree mic.input; phase -, nom. level 3mVrms Audio

J10

J10J10

J10

EAR_HF- AO Handsfree ear output, phase - Audio

H9

H9H9

H9

EAR_MT- AO Handset earphone signal output, phase - Audio

H10

H10H10

H10

EAR_HF+ AO Handsfree ear output, phase + Audio

SIM card interface

SIM card interfaceSIM card interface

SIM card interface

C10

C10C10

C10

SIMCLK O External SIM signal – Clock 1,8 / 3V

C11

C11C11

C11

SIMIN I External SIM signal - Presence (active low)

Pull up 47K

1,8 / 3V

D4

D4D4

D4

SIMVCC - External SIM signal – Power supply for the SIM 1,8 / 3V

D10

D10D10

D10

SIMIO I/O External SIM signal - Data I/O

Pull up

4.7K

1,8 / 3V

E9

E9E9

E9

SIMRST O External SIM signal – Reset 1,8 / 3V

Trace

TraceTrace

Trace

D11

D11D11

D11

TX_TRACE O TX Data for debug monitor CMOS 2.8V

F10

F10F10

F10

RX_TRACE I RX Data for debug monitor CMOS 2.8V

H4

H4H4

H4

SERVICE I

Service pin shall be used to upgrade the module

from ASC1 (RX_TRACE, TX_TRACE). The pin

shall be tied low to enable the feature only in

case of a SW Update activity. It is required, for

debug purpose, to be connected

to a test pad on the final application.

CMOS 2.8V

Prog. / Data + HW Flow Control

Prog. / Data + HW Flow ControlProg. / Data + HW Flow Control

Prog. / Data + HW Flow Control

B6

B6B6

B6

C125/RING O Output for Ring indicator signal (RI) to DTE CMOS 2.8V

B7

B7B7

B7

C108/DTR I Input for Data terminal ready signal (DTR) from DTE CMOS 2.8V

D9

D9D9

D9

C109/DCD O Output for Data carrier detect signal (DCD) to DTE CMOS 2.8V

E7

E7E7

E7

C103/TXD I Serial data input (TXD) from DTE CMOS 2.8V

E11

E11E11

E11

C107/DSR O Output for Data set ready signal (DSR) to DTE CMOS 2.8V

F7

F7F7

F7

C105/RTS I Input for Request to send signal (RTS) from DTE CMOS 2.8V

F6

F6F6

F6

C106/CTS O Output for Clear to send signal (CTS) to DTE CMOS 2.8V

H8

H8H8

H8

C104/RXD O Serial data output to DTE CMOS 2.8V

DA

DADA

DAC and ADC

C and ADCC and ADC

C and ADC

C7

C7C7

C7

DAC_OUT AO Digital/Analog converter output D/A

J11

J11J11

J11

ADC_IN1 AI Analog/Digital converter input A/D

H11

H11H11

H11

ADC_IN2 AI Analog/Digital converter input A/D

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

Ball

BallBall

Ball

Signal

SignalSignal

Signal

I/O

I/OI/O

I/O

Function

FunctionFunction

Function

Internal

Internal Internal

Internal

PULL UP

PULL UPPULL UP

PULL UP

Type

TypeType

Type

Miscellaneous Functions

Miscellaneous FunctionsMiscellaneous Functions

Miscellaneous Functions

A2

A2A2

A2

RESET* I Reset input

D8

D8D8

D8

STAT_LED O Status indicator led CMOS 1.8V

E2

E2E2

E2

VRTC AO VRTC Power

J5

J5J5

J5

ON_OFF* I

Input command for switching power ON or OFF (toggle

command). The pulse to be sent to the GE864-QUAD V2

must be equal or greater than 1 second.

Pull up 47K

Pull up to VBATT

L8

L8L8

L8

PWRMON I/O PWRMON CMOS 2.8V

L4

L4L4

L4

GSM Antenna O Antenna output – 50 ohm RF

Telit GPIO

Telit GPIOTelit GPIO

Telit GPIO / DVI

/ DVI / DVI

/ DVI

C1

C1C1

C1

GPIO_01 I/O GPIO_01 CMOS 2.8V

E6

E6E6

E6

GPIO_02 / JDR I/O GPIO_02 / JDR CMOS 2.8V

C2

C2C2

C2

GPIO_03 I/O GPIO_03 CMOS 2.8V

B3

B3B3

B3

GPIO_04 / TX_DISABLE I/O GPIO_04 / TX_DISABLE CMOS 2.8V

K8

K8K8

K8

GPIO_05 / RFTXMON I/O

Telit GPIO05 Configurable GPIO / Transmitter ON

monitor

CMOS 2.8V

B5

B5B5

B5

GPIO_06 / ALARM I/O Telit GPIO06 Configurable GPIO / ALARM CMOS 2.8V

L9

L9L9

L9

GPIO_07 / BUZZER I/O Telit GPIO07 Configurable GPIO / Buzzer CMOS 2.8V

K11

K11K11

K11

GPIO_08 I/O GPIO_08 CMOS 2.8V

C9

C9C9

C9

GPIO_09 I/O GPIO_09 CMOS 2.8V

H3

H3H3

H3

GPIO_10 / DVI_TX I/O GPIO_10 / DVI_TX CMOS 2.8V

K7

K7K7

K7

DVI_RX I/O DVI_RX CMOS 2.8V

D7

D7D7

D7

DVI_CLK I/O DVI_CLK CMOS 2.8V

H5

H5H5

H5

DVI_WA0 I/O DVI_WA0 CMOS 2.8V

Power Supply

Power SupplyPower Supply

Power Supply

J1

J1J1

J1

VBATT - Main power supply Power

K1

K1K1

K1

VBATT - Main power supply Power

J2

J2J2

J2

VBATT - Main power supply Power

K2

K2K2

K2

VBATT - Main power supply Power

A1

A1A1

A1

GND - Ground Power

A11

A11A11

A11

GND - Ground Power

D6

D6D6

D6

GND - Ground Power

F1

F1F1

F1

GND - Ground Power

F11

F11F11

F11

GND - Ground Power

H

HH

H1

11

1

GND - Ground Power

H2

H2H2

H2

GND - Ground Power

J3

J3J3

J3

GND - Ground Power

K3

K3K3

K3

GND - Ground Power

K4

K4K4

K4

GND - Ground Power

K5

K5K5

K5

GND - Ground Power

K6

K6K6

K6

GND - Ground Power

L1

L1L1

L1

GND - Ground Power

L2

L2L2

L2

GND - Ground Power

L3

L3L3

L3

GND - Ground Power

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

Ball

BallBall

Ball

Signal

SignalSignal

Signal

I/O

I/OI/O

I/O

Function

FunctionFunction

Function

Internal

Internal Internal

Internal

PULL UP

PULL UPPULL UP

PULL UP

Type

TypeType

Type

L6

L6L6

L6

GND - Ground Power

L11

L11L11

L11

GND - Ground Power

RESERVED

RESERVEDRESERVED

RESERVED

A3

A3A3

A3

- - Reserved

A4

A4A4

A4

- - Reserved

A5

A5A5

A5

- - Reserved

A6

A6A6

A6

- - Reserved

A7

A7A7

A7

- - Reserved

A8

A8A8

A8

- - Reserved

A9

A9A9

A9

- - Reserved

A10

A10A10

A10

- - Reserved

B1

B1B1

B1

- - Reserved

B2

B2B2

B2

- - Reserved

B4

B4B4

B4

- - Reserved

B8

B8B8

B8

- - Reserved

B9

B9B9

B9

- - Reserved

B10

B10B10

B10

- - Reserved

B11

B11B11

B11

- - Reserved

C3

C3C3

C3

- - Reserved

C4

C4C4

C4

- - Reserved

C5

C5C5

C5

- - Reserved

C6

C6C6

C6

- - Reserved

C8

C8C8

C8

- - Reserved

D1

D1D1

D1

- - Reserved

D2

D2D2

D2

- - Reserved

D3

D3D3

D3

- - Reserved

D5

D5D5

D5

- - Reserved

E1

E1E1

E1

- - Reserved

E3

E3E3

E3

- - Reserved

E4

E4E4

E4

- - Reserved

E5

E5E5

E5

- - Reserved

E8

E8E8

E8

- - Reserved

E10

E10E10

E10

- - Reserved

F2

F2F2

F2

- - Reserved

F3

F3F3

F3

- - Reserved

F4

F4F4

F4

- - Reserved

F5

F5F5

F5

- - Reserved

F8

F8F8

F8

- - Reserved

G1

G1G1

G1

- - Reserved

G2

G2G2

G2

- -

Reserved

G3

G3G3

G3

- - Reserved

G4

G4G4

G4

- - Reserved

G5

G5G5

G5

- - Reserved

G6

G6G6

G6

- - Reserved

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

Ball

BallBall

Ball

Signal

SignalSignal

Signal

I/O

I/OI/O

I/O

Function

FunctionFunction

Function

Internal

Internal Internal

Internal

PULL UP

PULL UPPULL UP

PULL UP

Type

TypeType

Type

G7

G7G7

G7

- - Reserved

G11

G11G11

G11

- - Reserved

H6

H6H6

H6

- - Reserved

H7

H7H7

H7

- - Reserved

J4

J4J4

J4

- - Reserved

J6

J6J6

J6

- -

Reserved

J7

J7J7

J7

- - Reserved

K9

K9K9

K9

- - Reserved

K10

K10K10

K10

- - Reserved

L5

L5L5

L5

- - Reserved

L7

L7L7

L7

- - Reserved

L10

L10L10

L10

- - Reserved

NOTE:

NOTE:NOTE:

NOTE:

The GE864-QUAD V2 / GE864-DUAL V2 Modules has only one DVI ports on the system

interface.

NOTE:

NOTE:NOTE:

NOTE:

Reserved pins must not be connected.

NOTE:

NOTE:NOTE:

NOTE:

RTS must be connected to the GND (on the module side) if flow control is not used.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

NOTE

NOTENOTE

NOTE:

::

:

If not used, almost all pins must be left disconnected. The only exceptions are the

following pins:

Ball

BallBall

Ball

Signal

SignalSignal

Signal

Function

FunctionFunction

Function

J

JJ

J1

11

1, J

, J, J

, J2

22

2, K1, K2

, K1, K2, K1, K2

, K1, K2

VBATT Main power supply

A1, A11, D6, F1, F11, H1,

A1, A11, D6, F1, F11, H1, A1, A11, D6, F1, F11, H1,

A1, A11, D6, F1, F11, H1,

H2, J3, K3, K4, K5

H2, J3, K3, K4, K5H2, J3, K3, K4, K5

H2, J3, K3, K4, K5, K6, L1,

, K6, L1, , K6, L1,

, K6, L1,

L2, L3, L6, L11

L2, L3, L6, L11L2, L3, L6, L11

L2, L3, L6, L11

GND Ground

E7

E7E7

E7

C103/TXD Serial data input (TXD) from DTE

H8

H8H8

H8

C104/RXD Serial data output to DTE

F7

F7F7

F7

C105/RTS Input for Request to send signal (RTS) from DTE

J5

J5J5

J5

ON/OFF* Input command for switching power ON or OFF (toggle command).

A2

A2A2

A2

RESET* Reset input

F10

F10F10

F10

RX_TRACE RX Data for debug monitor

D11

D11D11

D11

TX_TRACE TX Data for debug monitor

H4

H4H4

H4

SERVICE SERVICE connection

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

4.1.1.

4.1.1.4.1.1.

4.1.1. BGA Balls Layout

BGA Balls LayoutBGA Balls Layout

BGA Balls Layout

TOP VIEW

TOP VIEWTOP VIEW

TOP VIEW

A

AA

A

B

BB

B

C

CC

C

D

DD

D

E

EE

E

F

FF

F

G

GG

G

H

HH

H

J

JJ

J

K

KK

K

L

LL

L

1

11

1

GND - GPIO_01 - - GND - GND VBATT VBATT GND

2

22

2

RESET* - GPIO_03 - VRTC - - GND VBATT VBATT GND

3

33

3

-

GPIO_04 /

TX_DISABL

E

- - - _ -

GPIO_10 /

DVI_TX

GND GND GND

4

44

4

-- - - SIMVCC - - - SERVICE - GND

GSM

Antenna

5

55

5

-

GPIO_06 /

ALARM

- - - - -

DVI_WA0

ON_OFF* GND -

6

66

6

-

C125/RING

- GND

GPIO_02 /

JDR

C106 / CTS

- - - GND GND

7

77

7

- C108 / DTR

DAC_OUT DVI_CLK C103 / TXD

C105 / RTS

- - - DVI_RX -

8

88

8

- - - STAD_ LED

- - MIC_HF+ C104 / RXD

MIC_MT+

GPIO_05 /

RFTXMON

PWRMON

9

99

9

- - GPIO_09 C109 / DCD

SIMRST AXE MIC_MT- EAR_MT- MIC_HF- -

GPIO_07 /

BUZZER

10

1010

10

- - SIMCLK SIMIO

- RX_TRACE

EAR_MT+ EAR_HF+ EAR_HF- - -

11

1111

11

GND - SIMIN

TX_TRACE

C107 / DSR

GND - ADC_IN2 ADC_IN1 GPIO_08 GND

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

AUDIO Signals balls

SIM CARD interface balls

TRACE Signals balls

Prog. / data + Hw Flow Control signals balls

ADC signals balls

MISCELLANEOUS functions signals balls

TELIT GPIO balls

POWER SUPPLY VBATT balls

POWER SUPPLY GND balls

RESERVED

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

5. Hardware Commands

5.1. Turning ON the GE864-QUAD V2 / GE864-DUAL V2

To turn the GE864-QUAD V2 / GE864-DUAL V2 on, the pad ON# must be tied low for

at least 1000ms and then released. A pulse duration less than 1000ms should also

start the power on procedure, but this is not guaranteed.

The maximum current that can be drained from the ON# pad is 0,1 mA.

A simple circuit to do it is:

TIP:

TIP:TIP:

TIP:

To check if the device has powered on, the hardware line PWRMON must be

monitored. After 1000ms the line raised up the device could be considered powered

on.

NOTE:

NOTE:NOTE:

NOTE:

Do not use any pull up resistor on the ON# line, it is internally pulled up. Using pull

up resistor may bring to latch up problems on the GE864-QUAD V2 / GE864-DUAL V2

power regulator and improper power on/off of the module. The line ON# must be

connected only in open collector configuration.

In this document all the lines that are inverted, hence have active low signals are

labeled with a name that ends with a "#" or with a bar over the name.

NOTE

NOTENOTE

NOTE: When the power supply voltage is lower than 3.4V, to turn ON the module, the

pad ON# must be tied low for at least 3 seconds.

GE864

GE864GE864

GE864-

--

-QUAD V2 / GE864

QUAD V2 / GE864QUAD V2 / GE864

QUAD V2 / GE864-

--

-DUAL V2 Hardware User Guide

DUAL V2 Hardware User GuideDUAL V2 Hardware User Guide

DUAL V2 Hardware User Guide

1vv0300875 Rev.1 – 2010-03-29

For example:

1- Let us assume you need to drive the ON# pad with a totem pole output of a +3/5 V

microcontroller (uP_OUT1):

2- Let us assume you need to drive the ON# pad directly with an ON/OFF button:

A flow chart with proper turn on procedure is detailed below:

Page is loading ...

Telit Communications S.p.A. RI7GE864Q2B User manual

This manual is also suitable for

Telit Communications S.p.A. RI7GE864Q2B User manual

Related papers

Other documents