Pentair BE882 User manual

BE882
Pentair
Brand
Pentair
Model
BE882
Category
Wall & ceiling mounts accessories
Type
User manual

Pentair BE882 is a shaft replacement kit designed for easy and efficient replacement of worn or damaged shafts in compatible pumps. It includes all the necessary components, such as bearings, seals, and keys, to ensure a proper fit and reliable operation. The kit is compatible with specific Pentair pumps and is engineered to restore the pump's performance and longevity. With the Pentair BE882 shaft replacement kit, users can maintain their pumps in optimal condition, ensuring smooth operation and延长使用寿命.

Pentair BE882 is a shaft replacement kit designed for easy and efficient replacement of worn or damaged shafts in compatible pumps. It includes all the necessary components, such as bearings, seals, and keys, to ensure a proper fit and reliable operation. The kit is compatible with specific Pentair pumps and is engineered to restore the pump's performance and longevity. With the Pentair BE882 shaft replacement kit, users can maintain their pumps in optimal condition, ensuring smooth operation and延长使用寿命.

293 WRIGHT STREET, DELAVAN, WI 53115 WWW.BERKELEYPUMPS.COM
PH: 888-237-5353
INSTALLATION INSTRUCTIONS
B_ZQ_S SAE 1.510T Spline;
B_ZR_S Frame Mount
Shaft Replacement Kit
© 2013 Pentair, Ltd. All Rights Reserved. BE882 (Rev. 02/25/13)
GENERAL
Unpack shaft replacement kit and compare contents with the parts list below. Verify kit received is the
correct one for your operation.
California Proposition 65 Warning
This product and related accessories contain chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
PARTS LIST
Ref. Part B_ZQ_S B_ZR_S
No. Description Qty. B85738 B85739
1 Capscrew 1 S23621 S23621
2 Lockwasher 1 S23038 S23038
3 Impeller Washer 1 S06319 S06319
4 Slinger 1 S10964 S10964
5 Grease Seal 2 M12337 M12337
6 Shaft Sleeve 1 M15098L M15098L
7 Ball Bearing 1 M15097 M15097
8 Shaft Key 1 S23677 S23677
9A Shaft 1 M15092 –
9B Shaft 1 – M15091
10 Shaft Key 1 – S23941
11 Ball Bearing 1 M15096 M15096
12 Thrust Ring 1 M15095 M15095
13 Retaining Ring 1 M15094 M15094
12345
6
7
8
9B
9A 10
11
12 13
5
6078 0709
Bearing Frame
(Bracket)
Outer
Bearing
Cap
Pack Grease in areas
shown to protect bearings
during installation.
Slope grease away from
bearing rollers as shown.
6079 0709
1. Thoroughly steam clean or solvent wash the
bearing cavity of bearing bracket to remove
old grease and dirt. Check surface of bracket
for cracks, extreme corrosion, or other
defects that may make replacement of the
bracket necessary.
2. Pack bearings with a lithium based NGLI
No. 2 extra pressure ball bearing grease.
Force enough grease into each bearing to fill
internal space between the races.
3. Coat the bearing bores of bracket with oil.
Orient shaft kit in the direction shown above.
Protect the bearings from contamination
during installation by applying grease
around bearings as shown. Slide shaft and
bearing assembly into bearing bracket. When
threaded end of pump shaft comes through
inner grease seal, place slinger over end
of shaft. If packing gland is not of the split
variety, place it over the shaft at this time
as well. Slide shaft on through stuffing box
until the first bearing makes contact with the
bracket. BESURE that you do not damage the
inner grease seal. Carefully align bearing with
the bearing bore and press or slide bearing
assembly into place. Do not use excessive
force.
4. Install outer bearing cap tightly against
bracket.
5. Inject grease into grease fittings to fill cavities
behind bearings.
6. Reassemble pump parts and install unit.
Refer to pump owners manual for correct
installation procedures.
INSTALLATION
  • Page 1 1
  • Page 2 2

Pentair BE882 User manual

BE882
Pentair
Brand
Pentair
Model
BE882
Category
Wall & ceiling mounts accessories
Type
User manual

Pentair BE882 is a shaft replacement kit designed for easy and efficient replacement of worn or damaged shafts in compatible pumps. It includes all the necessary components, such as bearings, seals, and keys, to ensure a proper fit and reliable operation. The kit is compatible with specific Pentair pumps and is engineered to restore the pump's performance and longevity. With the Pentair BE882 shaft replacement kit, users can maintain their pumps in optimal condition, ensuring smooth operation and延长使用寿命.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents