GENMAX GM6000iED User manual

Brand: GENMAX

Model: GM6000iED

Type: User manual

GENMAX GM6000iED: Experience reliable power with this compact and portable generator. Powered by a 212cc OHV engine, it delivers 6000 surge watts and 5500 running watts. Featuring a fuel-efficient design, it offers extended run times, making it ideal for camping, tailgating, or power outages. Easily monitor power output and track maintenance intervals with the intuitive digital display. Stay safe with built-in CO monitoring and protection.

GENMAX GM6000iED: Experience reliable power with this compact and portable generator. Powered by a 212cc OHV engine, it delivers 6000 surge watts and 5500 running watts. Featuring a fuel-efficient design, it offers extended run times, making it ideal for camping, tailgating, or power outages. Easily monitor power output and track maintenance intervals with the intuitive digital display. Stay safe with built-in CO monitoring and protection.

GM6000iED Choke stepper motor

maintenance operation instructions

2022.6.9

Tool Introduction

电枪

Hand tools are also available:

1. Cross screwdriver

2. Tweezers or other sharp tools

cross gun

1 Removing the panel rear cover

•Before •After

1.Turn the knob to remove the battery

door; remove the 6 bolts with a cross

screwdriver or stun gun.

3. Throttle stepper

motor connection

box (if it cannot be

recognized,

disassemble the left

appearance cover）

2.Remove

the battery

door

2、Remove the left exterior cover

•Before •After

1.Use a cross

screwdriver or flathead

screwdriver to remove

the two bolts

3.You can feel it with

your hand to adjust the

position of the damper.

2.Snap the cover

down and remove

the cover

open choke

status

3、Check wiring

•Panel box (male plug) •Stepper motor socket

(female socket)

Yellow、 Orange、 Red

Pink（Black Red）、Blue、

blank

Red、orange、Yellow

Blank、Blue、Pink

1.Check whether the

wiring harness of the

plug-in box is correct

according to the picture

2.Observe whether the

pins are loose or

deformed.

4、repair

1.Use tweezers or

other sharp tools to

flatten the terminals.

2.Pull the terminal

out of the socket.

3.Lift up the reverse

button of the

terminal

4.Insert the wire harness

into the correct position

according to the diagram in

step 3, then push the

terminal inward, the

terminal will not come

loose。

5、Install

•Joint the two sockets

Note: When docking the socket, be careful not to insert the pins crookedly.

6、Install the panel rear cover

•Install the panel rear cover

1.Assemble the panel

back cover in place and

assemble the 6 Phillips

bolts.

2.Install the battery

door and lock the knob

in the vertical direction

7、Install the left exterior cover

Install the left exterior cover

Assemble the cover

plate in place and fasten

the two Phillips bolts.

8、Start-CO Alarm Self-Test

4.The CO alarm self-test flashes

the yellow light once and goes

out, indicating that the self-test is

successful and the CO alarm is

working normally.

1.Turn the switch to the fuel

gear and start again (after the

fuel tank is refueled).

2.Press the switch

to "ON" 3. Press the One

key start button to

start

1
2
3
4
5
6
7
8
9
10
11

GENMAX GM6000iED User manual

Brand: GENMAX

Model: GM6000iED

Type: User manual

GENMAX GM6000iED: Experience reliable power with this compact and portable generator. Powered by a 212cc OHV engine, it delivers 6000 surge watts and 5500 running watts. Featuring a fuel-efficient design, it offers extended run times, making it ideal for camping, tailgating, or power outages. Easily monitor power output and track maintenance intervals with the intuitive digital display. Stay safe with built-in CO monitoring and protection.

Related papers

GENMAX GM6000iED User manual

Other documents