KUZCO AT6510 Installation guide

Type
Installation guide

KUZCO AT6510 is an all-terior LED lamp wall sconce designed for both indoor and outdoor use. It features pre-wired LED modules, eliminating the need for bulb replacements, and is compatible with ELV (Electronic Low Voltage) type dimmers for adjustable lighting. The fixture comes with a canopy backplate and mounting plate for easy installation onto a junction box. For outdoor installations, weather-resistant caulking is recommended to prevent moisture from entering the outlet box.

KUZCO AT6510 is an all-terior LED lamp wall sconce designed for both indoor and outdoor use. It features pre-wired LED modules, eliminating the need for bulb replacements, and is compatible with ELV (Electronic Low Voltage) type dimmers for adjustable lighting. The fixture comes with a canopy backplate and mounting plate for easy installation onto a junction box. For outdoor installations, weather-resistant caulking is recommended to prevent moisture from entering the outlet box.

INSTALLATION SHEET
AT6510
All-terior LED Lamp Wall Sconce
START FROM HERE
Make sure power is completely off at the fuse box.
Have your fixture installed by a qualified licensed electrician
Prepare everything in a clear area.
Wear gloves at all times during this installation.
Read instructions carefully before you start assembly.
Keep this instruction sheet for future reference.
Technical Support: 1-855-855-8926
2a.
1c.
1b.
1a. 1d.
2d.
2b. 2c.
19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
20181127
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s).
• Unless instructed to do so, please do not touch any part of the LED module(s) as any
unnecessary contact with the module could cause permanent damage.
• For dimming, an ELV (Electronic Low Voltage) type of dimmer is required.
caulking
You have now completed the installation of your fixture,
enjoy.
Remove the fixture from its original packaging. Remove
the mounting plate (1c) from within the canopy backplate
(2a) by loosening the four set screws (2d) and two screws
(2b). Secure the mounting plate (1c) to the junction box
(1a) with screws (1d) provided in the hardware package.
Attach the canopy backplate (2a) to the mounting plate
(1c), which is attached to the electrical junction box (1a)
on the wall. First attach all wiring with the provided
marrettes (1b) (white to white “N”, black to black “L”,
ground to ground “G”). Now direct the canopy backplate
(2a) onto the mounting plate (1c) be sure to line up the
mounting threaded holes with the screws (2b). Next, place
the canopy (2c) onto the canopy backplate (2a) and
secure with all four set screws (2d) turning clockwise.
1.
2.
3. *FOR OUTDOOR OPTION ONLY*
To prevent moisture from entering the outlet box and
causing a short, seal around the top and side perimeter
between the fixture and the wall surface with weather
resistant caulking (see Outdoor Option). The space at
bottom should be left un-caulked to prevent moisture
build-up.
4.
Outdoor Option
  • Page 1 1

KUZCO AT6510 Installation guide

Type
Installation guide

KUZCO AT6510 is an all-terior LED lamp wall sconce designed for both indoor and outdoor use. It features pre-wired LED modules, eliminating the need for bulb replacements, and is compatible with ELV (Electronic Low Voltage) type dimmers for adjustable lighting. The fixture comes with a canopy backplate and mounting plate for easy installation onto a junction box. For outdoor installations, weather-resistant caulking is recommended to prevent moisture from entering the outlet box.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI