Catalyst 9800-L-F Wireless Controller

Cisco Catalyst 9800-L-F Wireless Controller , Catalyst 9800 Series Wireless Controllers, Catalyst 9800-40 Wireless Controller , Catalyst 9800-80 Wireless Controller , Catalyst 9800-L Wireless Controller , Catalyst 9800-L-C Wireless Controller Configuration Guide

  • Hello! I am an AI chatbot trained to assist you with the Cisco Catalyst 9800-L-F Wireless Controller Configuration Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Cisco Catalyst 9800 Series Wireless Controller Software Configuration
Guide, Cisco IOS XE Amsterdam 17.2.x
First Published: 2020-03-31
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1721R)
©2020 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface lxvii
PREFACE
Document Conventions lxvii
Related Documentation lxix
Obtaining Documentation and Submitting a Service Request lxix
Overview of Cisco 9800 Series Wireless Controllers 1
CHAPTER 1
Elements of the New Configuration Model 1
Configuration Workflow 2
Initial Setup 3
System Configuration 5
PART I
System Configuration 7
CHAPTER 2
Information About New Configuration Model 7
Configuring a Wireless Profile Policy (GUI) 9
Configuring a Wireless Profile Policy (CLI) 10
Configuring a Flex Profile (GUI) 11
Configuring a Flex Profile 12
Configuring an AP Profile (GUI) 12
Configuring an AP Profile (CLI) 17
Configuring User for AP Management (CLI) 18
Setting a Private Configuration Key for Password Encryption 18
Configuring an RF Profile (GUI) 19
Configuring an RF Profile (CLI) 19
Configuring a Site Tag (GUI) 20
Configuring a Site Tag (CLI) 21
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
iii
Configuring Policy Tag (GUI) 22
Configuring a Policy Tag (CLI) 22
Configuring Wireless RF Tag (GUI) 24
Configuring Wireless RF Tag (CLI) 24
Attaching a Policy Tag and Site Tag to an AP (GUI) 25
Attaching Policy Tag and Site Tag to an AP (CLI) 25
AP Filter 26
Introduction to AP Filter 26
Set Tag Priority (GUI) 27
Set Tag Priority 27
Create an AP Filter (GUI) 28
Create an AP Filter (CLI) 28
Set Up and Update Filter Priority (GUI) 29
Set Up and Update Filter Priority 29
Verify AP Filter Configuration 30
Configuring Access Point for Location Configuration 31
Information About Location Configuration 31
Prerequisite for Location Configuration 31
Configuring a Location for an Access Point (GUI) 31
Configuring a Location for an Access Point (CLI) 32
Adding an Access Point to the Location (GUI) 33
Adding an Access Point to the Location (CLI) 33
Configuring SNMP in Location Configuration 34
SNMP MIB 34
Verifying Location Configuration 34
Verifying Location Statistics 35
RF Profile 37
CHAPTER 3
RF Tag Profiles 37
Configuring an AP Tag (GUI) 37
Configuring AP Tag (CLI) 38
Configuring RF Profile (GUI) 39
Configuring an RF Profile (CLI) 40
Configuring Wireless RF Tag (GUI) 41
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
iv
Contents
Configuring Wireless RF Tag (CLI) 42
BIOS Protection 45
CHAPTER 4
BIOS Protection on the Controller 45
BIOS or ROMMON Upgrade with BIOS Protection 45
Upgrading BIOS 46
Smart Licensing 47
CHAPTER 5
Information About Cisco Smart Licensing 47
Creating a Smart Account 49
Using Smart Licensing 50
Reregister a License (GUI) 50
Using Specified License Reservation (SLR) 51
Enabling Smart Software Licensing 51
Enabling Smart Call Home Reporting 52
Configuring AIR License Level (GUI) 53
Configuring AIR License Level (CLI) 53
Configuring AIR Network Essentials License Level 54
Configuring AIR Network Advantage License Level 54
Enabling High-Performance License 55
Verifying Smart Licensing Configurations 57
Best Practices 59
CHAPTER 6
Introduction 59
System Upgrade 61
PART II
Upgrading the Cisco Catalyst 9800 Wireless Controller Software 63
CHAPTER 7
Overview of Upgrading the Controller Software 63
Upgrading the Controller Software (GUI) 64
Upgrade the Controller Software (CLI) 65
Converting From Bundle-Mode to Install-Mode 66
In-Service Software Upgrade 71
CHAPTER 8
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
v
Contents
Information About In-Service Software Upgrade 71
Prerequisites for Performing In-Service Software Upgrade 72
Guidelines and Restrictions for In-Service Software Upgrade 72
Upgrading Software Using In-Service Software Upgrade 73
Upgrading Software Using ISSU (GUI) 74
Upgrading Software Using In-Service Software Upgrade with Delayed Commit 75
Monitoring In-Service Software Upgrade 76
Troubleshooting ISSU 78
Software Maintenance Upgrade 81
CHAPTER 9
Introduction to Software Maintenance Upgrade 81
Installing a SMU (GUI) 82
Installing SMU 83
Roll Back an Image (GUI) 83
Rollback SMU 84
Deactivate SMU 84
Configuration Examples for SMU 84
Information About AP Device Package 85
Installing AP Device Package (GUI) 86
Installing AP Device Package (CLI) 86
Verifying APDP on the Controller 87
Information About Per Site or Per AP Model Service Pack (APSP) 88
Rolling AP Upgrade 89
Rolling AP Upgrade Process 89
Installing AP Service Package (GUI) 90
Installing AP Service Package (CLI) 90
Adding a Site to a Filter 91
Deactivating an Image 92
Roll Back APSP 92
Canceling the Upgrade 93
Verifying the Upgrade 93
Verifying of AP Upgrade on the Controller 94
Efficient Image Upgrade 97
CHAPTER 10
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
vi
Contents
Efficient Image Upgrade 97
Enable Pre-Download (GUI) 97
Enable Pre-Download (CLI) 98
Configuring a Site Tag (CLI) 98
Attaching Policy Tag and Site Tag to an AP (CLI) 99
Trigger Predownload to a Site Tag 100
Predownloading an Image to an Access Point 103
CHAPTER 11
Information About Predownloading an Image to an Access Point 103
Restrictions for Predownloading an Image to an Access Point 103
Predownloading an Image to Access Points (CLI) 104
Monitoring the Access Point Predownload Process 105
N+1 Hitless Rolling AP Upgrade 107
CHAPTER 12
N+1 Hitless Rolling AP Upgrade 107
Configuring Hitless Upgrade 108
Verifying Hitless Upgrade 109
NBAR Dynamic Protocol Pack Upgrade 111
CHAPTER 13
NBAR Dynamic Protocol Pack Upgrade 111
Upgrading the NBAR2 Protocol Pack 112
Wireless Sub-Package for Switch 113
CHAPTER 14
Introduction to Wireless Sub-package 113
Booting in Install Mode 114
Installing Sub-Package in a Single Step (GUI) 115
Installing Sub-Package in a Single Step 115
Multi-step Installation of Sub-Package 116
Installing on a Stack 117
Upgrading to a Newer Version of Wireless Package 117
Deactivating the Wireless Package 117
Enabling or Disabling Auto-Upgrade 118
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
vii
Contents
Lightweight Access Points 119
PART III
Country Codes 121
CHAPTER 15
Information About Country Codes 121
Prerequisites for Configuring Country Codes 121
Configuring Country Codes (GUI) 122
How to Configure Country Codes 122
Configuration Examples for Configuring Country Codes 124
Viewing Channel List for Country Codes 124
Sniffer Mode 127
CHAPTER 16
Information about Sniffer 127
Prerequisites for Sniffer 127
Restrictions on Sniffer 127
How to Configure Sniffer 128
Configuring an Access Point as Sniffer (GUI) 128
Configuring an Access Point as Sniffer (CLI) 128
Enabling or Disabling Sniffing on the Access Point (GUI) 129
Enabling or Disabling Sniffing on the Access Point (CLI) 129
Verifying Sniffer Configurations 130
Examples for Sniffer Configurations and Monitoring 130
Monitor Mode 131
CHAPTER 17
Introduction to Monitor Mode 131
Enable Monitor Mode (GUI) 131
Enable Monitor Mode (CLI) 132
AP Priority 133
CHAPTER 18
Failover Priority for Access Points 133
Setting AP Priority (GUI) 133
Setting AP Priority 134
FlexConnect 135
CHAPTER 19
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
viii
Contents
Information About FlexConnect 135
FlexConnect Authentication Process 137
Guidelines and Restrictions for FlexConnect 140
Configuring a Site Tag 142
Configuring a Policy Tag (CLI) 143
Attaching a Policy Tag and a Site Tag to an AP (GUI) 144
Attaching Policy Tag and Site Tag to an AP (CLI) 145
Linking an ACL Policy to the Defined ACL (GUI) 146
Applying ACLs on FlexConnect 146
Configuring FlexConnect 147
Configuring a Switch at a Remote Site 147
Configuring the Controller for FlexConnect 148
Configuring Local Switching in FlexConnect Mode (GUI) 149
Configuring Local Switching in FlexConnect Mode (CLI) 149
Configuring Central Switching in FlexConnect Mode (GUI) 150
Configuring Central Switching in FlexConnect Mode 150
Configuring an Access Point for FlexConnect 151
Configuring an Access Point for Local Authentication on a WLAN (GUI) 151
Configuring an Access Point for Local Authentication on a WLAN (CLI) 151
Connecting Client Devices to WLANs 151
Configuring FlexConnect Ethernet Fallback 152
Information About FlexConnect Ethernet Fallback 152
Configuring FlexConnect Ethernet Fallback 152
Flex AP Local Authentication (GUI) 153
Flex AP Local Authentication (CLI) 154
Flex AP Local Authentication with External Radius Server 156
Configuration Example: FlexConnect with Central and Local Authentication 159
NAT-PAT for FlexConnect 159
Configuring NAT-PAT for a WLAN or a Remote LAN 159
Creating a WLAN 159
Configuring a Wireless Profile Policy and NAT-PAT (GUI) 160
Configuring a Wireless Profile Policy and NAT-PAT 160
Mapping a WLAN to a Policy Profile 161
Configuring a Site Tag 162
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
ix
Contents
Attaching a Policy Tag and a Site Tag to an Access Point (GUI) 162
Attaching a Policy Tag and a Site Tag to an Access Point 163
Split Tunneling for FlexConnect 163
Configuring Split Tunneling for a WLAN or Remote LAN 164
Defining an Access Control List for Split Tunneling (GUI) 164
Defining an Access Control List for Split Tunneling 164
Linking an ACL Policy to the Defined ACL 165
Creating a WLAN 166
Configuring a Wireless Profile Policy and a Split MAC ACL Name (GUI) 166
Configuring a Wireless Profile Policy and a Split MAC ACL Name 167
Mapping a WLAN to a Policy Profile (GUI) 168
Mapping WLAN to a Policy Profile 168
Configuring a Site Tag 169
Attaching a Policy Tag and Site Tag to an Access Point 169
VLAN-based Central Switching for FlexConnect 170
Configuring VLAN-based Central Switching (GUI) 170
Configuring VLAN-based Central Switching (CLI) 171
OfficeExtend Access Points for FlexConnect 172
Configuring OfficeExtend Access Points 172
Disabling OfficeExtend Access Point 173
Clearing Personal SSID from an OfficeExtend Access Point 174
Example: Viewing OfficeExtend Configuration 174
Proxy ARP 175
Enabling Proxy ARP for FlexConnect APs (GUI) 175
Enabling Proxy ARP for FlexConnect APs 175
Data DTLS 177
CHAPTER 20
Information About Data Datagram Transport Layer Security 177
Configuring Data DTLS (GUI) 177
Configuring Data DTLS (CLI) 178
Converting Autonomous Access Points to Lightweight Mode 181
CHAPTER 21
Guidelines for Converting Autonomous Access Points to Lightweight Mode 181
Information About Autonomous Access Points Converted to Lightweight Mode 182
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
x
Contents
Reverting from Lightweight Mode to Autonomous Mode 182
Using DHCP Option 43 and DHCP Option 60 182
How Converted Access Points Send Crash Information to the Device 183
Uploading Memory Core Dumps from Converted Access Points 183
Displaying MAC Addresses for Converted Access Points 183
Configuring a Static IP Address for a Lightweight Access Point 183
How to Convert a Lightweight Access Point Back to an Autonomous Access Point 184
Converting a Lightweight Access Point Back to an Autonomous Access Point (CLI) 184
Converting a Lightweight Access Point Back to an Autonomous Access Point (Using the Mode
Button and a TFTP Server) 184
Authorizing Access Points 185
Authorizing Access Points Using Local Database (CLI) 185
Authorizing Access Points Using RADIUS Server (CLI) 186
Disabling the Reset Button on Converted Access Points (CLI) 188
Monitoring the AP Crash Log Information 188
How to Configure a Static IP Address on an Access Point 189
Configuring a Static IP Address on an Access Point (CLI) 189
Configuring a Static IP Address on an Access Point (GUI) 190
Recovering the Access Point Using the TFTP Recovery Procedure 191
Configuration Examples for Converting Autonomous Access Points to Lightweight Mode 191
Example: Displaying the IP Address Configuration for Access Points 191
Example: Displaying Access Point Crash File Information 191
AP MAC Authorization 192
Configuring AP MAC Authorization (CLI) 192
Ethernet VLAN Tagging on Access Points 193
Information About Ethernet VLAN Tagging on Access Points 193
Configuring Ethernet VLAN Tagging on Access Points (GUI) 193
Configuring Ethernet VLAN Tagging on Access Points (CLI) 193
AP Crash File Upload 195
CHAPTER 22
AP Crash File Upload 195
Configuring AP Crash File Upload (CLI) 196
Access Point Plug-n-Play 197
CHAPTER 23
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xi
Contents
Overview of Access Point Plug-n-Play 197
Provisioning AP from PnP Server 197
Verifying AP Tag Configuration 198
802.11 Parameters for Cisco Access Points 199
CHAPTER 24
2.4-GHz Radio Support 199
Configuring 2.4-GHz Radio Support for the Specified Slot Number 199
5-GHz Radio Support 201
Configuring 5-GHz Radio Support for the Specified Slot Number 201
Information About Dual-Band Radio Support 203
Configuring Default XOR Radio Support 203
Configuring XOR Radio Support for the Specified Slot Number (GUI) 206
Configuring XOR Radio Support for the Specified Slot Number 206
Receiver Only Dual-Band Radio Support 208
Information About Receiver Only Dual-Band Radio Support 208
Configuring Receiver Only Dual-Band Parameters for Access Points 208
Enabling CleanAir with Receiver Only Dual-Band Radio on a Cisco Access Point (GUI) 208
Enabling CleanAir with Receiver Only Dual-Band Radio on a Cisco Access Point 208
Disabling Receiver Only Dual-Band Radio on a Cisco Access Point (GUI) 209
Disabling Receiver Only Dual-Band Radio on a Cisco Access Point 209
Configuring Client Steering (CLI) 209
Verifying Cisco Access Points with Dual-Band Radios 211
802.1x Support 213
CHAPTER 25
Introduction to the 802.1x Authentication 213
EAP-FAST Protocol 213
EAP-TLS/EAP-PEAP Protocol 214
Limitations of the 802.1x Authentication 214
Topology - Overview 214
Configuring 802.1x Authentication Type and LSC AP Authentication Type (GUI) 215
Configuring 802.1x Authentication Type and LSC AP Authentication Type 215
Configuring the 802.1x Username and Password (GUI) 216
Configuring the 802.1x Username and Password (CLI) 217
Enabling 802.1x on the Switch Port 218
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xii
Contents
Verifying 802.1x on the Switch Port 219
Verifying the Authentication Type 220
Configuring CAPWAP Link Aggregation Support 221
CHAPTER 26
Information About Link Aggregation 221
Information About CAPWAP LAG Support 221
Restrictions for CAPWAP LAG Support 222
Enabling CAPWAP LAG Support on Controller (GUI) 222
Enabling CAPWAP LAG Support on Controller 222
Enabling CAPWAP LAG Globally on Controller 223
Disabling CAPWAP LAG Globally on Controller 223
Enabling CAPWAP LAG for an AP Profile (GUI) 223
Enabling CAPWAP LAG for an AP Profile 224
Disabling CAPWAP LAG for an AP Profile 224
Disabling CAPWAP LAG Support on Controller 225
Verifying CAPWAP LAG Support Configurations 225
Configuring DHCP and NAT Functionality on Root Access Point 227
CHAPTER 27
Information About DHCP and NAT Functionality on Root AP (RAP) 227
Configuring DHCP Server on Root Access Point (RAP) 228
Verifying DHCP Server for Root AP Configuration 228
OFDMA Support for 11ax Access Points 229
CHAPTER 28
Information About OFDMA Support for 11ax Access Points 229
Supported Modes on 11ax Access Points 229
Configuring 11AX (GUI) 230
Configuring Channel Width 230
Configuring 802.11ax Radio Parameters (GUI) 231
Configuring 802.11ax Radio Parameters (CLI) 231
Setting up the 802.11ax Radio Parameters 232
Configuring OFDMA on a WLAN 233
Verifying Channel Width 234
Verifying Client Details 235
Verifying Radio Configuration 236
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xiii
Contents
Radio Resource Management 239
PART IV
Radio Resource Management 241
CHAPTER 29
Information About Radio Resource Management 241
Radio Resource Monitoring 242
Information About RF Groups 242
RF Group Leader 243
RF Group Name 245
Rogue Access Point Detection in RF Groups 246
Transmit Power Control 246
Overriding the TPC Algorithm with Minimum and Maximum Transmit Power Settings 246
Dynamic Channel Assignment 247
Dynamic Bandwidth Selection 248
Coverage Hole Detection and Correction 249
Restrictions for Radio Resource Management 249
How to Configure RRM 250
Configuring Neighbor Discovery Type (GUI) 250
Configuring Neighbor Discovery Type (CLI) 250
Configuring RF Groups 250
Configuring RF Group Selection Mode (GUI) 251
Configuring RF Group Selection Mode (CLI) 251
Configuring an RF Group Name (CLI) 252
Configuring Members in an 802.11 Static RF Group (GUI) 252
Configuring Members in an 802.11 Static RF Group (CLI) 253
Configuring Transmit Power Control 253
Configuring Transmit Power (GUI) 253
Configuring the Tx-Power Control Threshold (CLI) 254
Configuring the Tx-Power Level (CLI) 254
Configuring 802.11 RRM Parameters 255
Configuring Advanced 802.11 Channel Assignment Parameters (GUI) 255
Configuring Advanced 802.11 Channel Assignment Parameters (CLI) 256
Configuring 802.11 Coverage Hole Detection (GUI) 259
Configuring 802.11 Coverage Hole Detection (CLI) 259
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xiv
Contents
Configuring 802.11 Event Logging (CLI) 260
Configuring 802.11 Statistics Monitoring (GUI) 261
Configuring 802.11 Statistics Monitoring (CLI) 262
Configuring the 802.11 Performance Profile (GUI) 263
Configuring the 802.11 Performance Profile (CLI) 263
Configuring Advanced 802.11 RRM 264
Enabling Channel Assignment (GUI) 264
Enabling Channel Assignment (CLI) 265
Restarting DCA Operation 265
Updating Power Assignment Parameters (GUI) 265
Updating Power Assignment Parameters (CLI) 266
Configuring Rogue Access Point Detection in RF Groups 266
Configuring Rogue Access Point Detection in RF Groups (CLI) 266
Monitoring RRM Parameters and RF Group Status 267
Monitoring RRM Parameters 267
Verifying RF Group Status (CLI) 268
Examples: RF Group Configuration 269
Information About ED-RRM 269
Configuring ED-RRM on the Cisco Wireless LAN Controller (CLI) 269
Coverage Hole Detection 273
CHAPTER 30
Coverage Hole Detection and Correction 273
Configuring Coverage Hole Detection (GUI) 273
Configuring Coverage Hole Detection (CLI) 274
Configuring CHD for RF Tag Profile (GUI) 275
Configuring CHD for RF Tag Profile (CLI) 276
Optimized Roaming 279
CHAPTER 31
Optimized Roaming 279
Restrictions for Optimized Roaming 279
Configuring Optimized Roaming (GUI) 280
Configuring Optimized Roaming (CLI) 280
Cisco Flexible Radio Assignment 281
CHAPTER 32
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xv
Contents
Information About Flexible Radio Assignment 281
Benefits of the FRA Feature 282
Configuring an FRA Radio (CLI) 282
Configuring an FRA Radio (GUI) 284
XOR Radio Support 285
CHAPTER 33
Information About Dual-Band Radio Support 285
Configuring Default XOR Radio Support 286
Configuring XOR Radio Support for the Specified Slot Number (GUI) 288
Configuring XOR Radio Support for the Specified Slot Number 288
Cisco Receiver Start of Packet 291
CHAPTER 34
Information About Receiver Start of Packet Detection Threshold 291
Restrictions for Rx SOP 291
Configuring Rx SOP (CLI) 292
Customizing RF Profile (CLI) 292
Client Limit 295
CHAPTER 35
Information About Client Limit 295
Configuring Client Limit (GUI) 295
Configuring Client Limit (CLI) 295
IP Theft 297
CHAPTER 36
Introduction to IP Theft 297
Configuring IP Theft (GUI) 298
Configuring IP Theft 298
Configuring the IP Theft Exclusion Timer 298
Adding Static Entries for Wired Hosts 299
Verifying IP Theft Configuration 300
Unscheduled Automatic Power Save Delivery 303
CHAPTER 37
Information About Unscheduled Automatic Power Save Delivery 303
Viewing Unscheduled Automatic Power Save Delivery (CLI) 303
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xvi
Contents
Target Wake Time 305
CHAPTER 38
Target Wake Time 305
Extended Power-Savings Using Target Wake Time 305
Configuring Target Wake Time at the Radio Level (CLI) 306
Configuring Target Wake Time on WLAN 307
Enabling Target Wake Time on WLAN (CLI) 307
Disabling Target Wakeup Time on WLAN (CLI) 308
Configuring Target Wake Time (GUI) 309
Verifying Target Wakeup Time 309
Enabling USB Port on Access Points 311
CHAPTER 39
USB Port as Power Source for Access Points 311
Configuring an AP Profile (CLI) 312
Configuring USB Settings for an Access Point (CLI) 312
Monitoring USB Configurations for Access Points (CLI) 313
Dynamic Frequency Selection 315
CHAPTER 40
Information About Dynamic Frequency Selection 315
Configuring Dynamic Frequency Selection (GUI) 315
Configuring Dynamic Frequency Selection 315
Verifying DFS 316
Cisco Access Points with Tri-Radio 317
CHAPTER 41
Cisco Access Points with Tri-Radio 317
Guidelines and Restrictions for Tri-Radio Access Points 319
Configuring Tri-Radio 319
Enabling or Disabling Tri-Radio on Cisco APs 319
Configuring 5-GHz Dual Radio Mode for AP (GUI) 319
Configuring the Dual Radio Mode and Enabling Slots (CLI) 320
Setting Radio Roles for Slots 320
Configuring the Tri-Radio Dual Radio Role (CLI) 321
Verifying Tri-Radio Configuration on the Controller 321
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xvii
Contents
Network Management 323
PART V
AP Packet Capture 325
CHAPTER 42
Introduction to AP Client Packet Capture 325
Enabling Packet Capture (GUI) 325
Enabling Packet Capture (CLI) 326
Create AP Packet Capture Profile and Map to an AP Join Profile (GUI) 326
Create AP Packet Capture Profile and Map to an AP Join Profile 326
Start or Stop Packet Capture 327
DHCP Option82 329
CHAPTER 43
Information About DHCP Option 82 329
Configuring DHCP Option 82 Global Interface 330
Configuring DHCP Option 82 Globally Through Server Override (CLI) 330
Configuring DHCP Option 82 Globally Through Different SVIs (GUI) 331
Configuring DHCP Option 82 Globally Through Different SVIs (CLI) 331
Configuring DHCP Option 82 Format 332
Configuring DHCP Option82 Through a VLAN Interface 333
Configuring DHCP Option 82 Through Option-Insert Command (CLI) 333
Configuring DHCP Option 82 Through the server-ID-override Command (CLI) 334
Configuring DHCP Option 82 Through a Subscriber-ID (CLI) 335
Configuring DHCP Option 82 Through server-ID-override and subscriber-ID Commands (CLI)
336
Configuring DHCP Option 82 Through Different SVIs (CLI) 337
RADIUS Realm 339
CHAPTER 44
Information About RADIUS Realm 339
Enabling RADIUS Realm 340
Configuring Realm to Match the RADIUS Server for Authentication and Accounting 340
Configuring the AAA Policy for a WLAN 341
Verifying the RADIUS-Realm Configuration 343
RADIUS Accounting 345
CHAPTER 45
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xviii
Contents
Information About RADIUS Accounting of AP Events 345
Configuring Accounting Method-List for an AP Profile 345
Verifying the AP Accounting Information 346
Cisco StadiumVision 347
CHAPTER 46
Cisco StadiumVision Overview 347
Configure Wireless Controller Parameters for Cisco StadiumVision (GUI) 348
Configure Wireless Controller Parameters for Cisco StadiumVision (CLI) 348
Verify StadiumVision Configurations 349
Persistent SSID Broadcast 351
CHAPTER 47
Persistent SSID Broadcast 351
Configuring Persistent SSID Broadcast 351
Verifying Persistent SSID Broadcast 352
Network Monitoring 353
CHAPTER 48
Network Monitoring 353
Status Information Received Synchronously - Configuration Examples 353
Alarm and Event Information Received Asynchronously - Configuration Examples 355
Creating a Lobby Ambassador Account 357
CHAPTER 49
Information About Lobby Ambassador Account 357
Creating a Lobby Ambassador User Account (GUI) 357
Creating a User Account 358
Logging In Using the Lobby Account 359
Creating a Lobby Ambassador Account (CLI) 359
Lobby Ambassador Account 361
CHAPTER 50
Information About Lobby Ambassador Account 361
Creating a Lobby Ambassador User Account (GUI) 362
Creating a User Account 362
Logging In Using the Lobby Account 363
Creating a Lobby Ambassador Account (CLI) 363
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xix
Contents
Configuring WLAN (GUI) 364
Client Allowed List 365
Restrictions for Client Allowed List 365
Creating a Client Allowed List (GUI) 365
Adding Single MAC Address to Allowed List 365
Adding Bulk MAC Address to Allowed List 366
Managing Guest Users 366
Viewing a Client Allowed List 367
Configuring Guest User Accounts 369
CHAPTER 51
Information About Creating Guest User Accounts 369
Creating a Guest User Account (GUI) 369
Creating a Guest User Account (CLI) 370
Verifying Guest User Account 371
Assigning Username to Guest Users in a WLAN (CLI) 372
System Management 373
PART VI
Network Mobility Services Protocol 375
CHAPTER 52
Information About Network Mobility Services Protocol 375
Radioactive Tracing for NMSP 376
Enabling NMSP on Premises Services 376
Modifying the NMSP Notification Interval for Clients, RFID Tags, and Rogues 377
Modifying the NMSP Notification Threshold for Clients, RFID Tags, and Rogues 377
Configuring NMSP Strong Cipher 378
Verifying NMSP Settings 378
Examples: NMSP Settings Configuration 381
NMSP by AP Groups with Subscription List from CMX 381
Verifying NMSP by AP Groups with Subscription List from CMX 381
Probe RSSI Location 383
Configuring Probe RSSI 383
RFID Tag Support 385
Configuring RFID Tag Support 385
Verifying RFID Tag Support 386
Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x
xx
Contents
/