Bachmann E-Z Command Dynamis Setup

Brand: Bachmann

Model: E-Z Command Dynamis

Type: Setup

Dynamis Digital trainset set up -

please read before using your trainset

Step 1: Getting Started

Connect the Basestation to power supply. Insert batteries into handset and turn on.

Press the Stop Key if the indicator is ‘ON’. The IR Receiver LEDs will flash for a few seconds

as connection is made.

From new, your train has a default address of 3, Dynamis powers on ready to operate a

train with an address of 3.

Dynamis has a context menu. A list of the meanings of each item is shown overleaf.

Step 2: Turning the headlights on

Press headlight key to turn

headlights ON/OFF

Step 5. Running another train

Press [LOCO] and enter the address of the

loco / train to be run.

If there is already a roster entry this will be

shown, otherwise a new roster record is

created with the default name of

‘Locomotive X’ where X was the address

entered. This can be changed to be a more

representative name (step 3 on left).

Keypad for

direct

control of up

to 21

functions,

accessory

hotkeys and

alpha

numerical

keypad for

loco and

accessory

address

entry

Handset features

Action keys

Left hand is MODE key to switch between locomotive and accessory control

Emergency stop

Infrared receiver / transmitter

Screen

Direction

Battery

compartment

ON/OFF switch

Lanyard fixing

Joystick

Battery

compartment

Headlights

Step 4. Changing the handset roster information

To change the name press -

EDIT NAME

Use

to delete default name

Enter a new name eg

CLASS 150 DMU

using the keypad

To change the Icon press -

[SCROLL]

EDIT SYMBOL

choose one of the icons,

or none.

Thank you for your choice of the Bachmann Branchline Dynamis Digital Trainset. Please take

a few moments to familiarise yourself with the system. Please also refer to the enclosed

general train set User Guide, although some set contents may differ.

The tape under the Basestation should only be removed to expand the system with the

separately available ProBox.

Step 3: Changing the address of your train

Each digital train has an address - a number between 1 and 9999 - that it will respond to

The address can be changed as often as desired, but when carrying out this procedure the

train being addressed must be the only train on the track connected to the Dynamis

Use WRITE ADDRESS ON SERVICE TRACK option in the Program menu

press

[SCROLL]

PROGRAM

[SCROLL]

WRITE ADDR ON SERVICE TRACK

Use to delete existing address then, enter the new address and press [PROG]

The train will move momentarily during programming. Shift key to access

F11 to F20

Dynamis Train Set User Guide V01 Jun 09

Indicators for decoder function status

ON / OFF

Infra red signal

condition

Track short circuit reported by

Command station

STOP

indicator Low battery power

Text, including loco details

and menus etc

Speed and direction indicators

Consist

indicator

Action Key icons

Used only when

the Dynamis Pro

Box is also used

Shift key pressed

indicator

Headlights ON

indicator

Screen Reference

Action key icons

[CONSIST]

[MENU]

[LOCO]

[CV<>]

[<>VALUE]

[ACCEPT] [CANCEL]

[READ] [PROG]

[BKSP]

Add loco to / remove from Consist

Select locomotive by address

Turnout / accessory operation - turnouts

left / right or accessories on / off

Access the menu

Accept Cancel

Scroll left or right

Move between CV selection and value for

CV in the programming menus

Write value to CV / read from CV

Backspace in text entry

[DIVERGE]

[STRAIGHT]

Description of action

Description of key

in User Guide

[SCROLL]

Full instructions for the use of Dynamis are

contained in the accompanying User Guide

Bachmann E-Z Command Dynamis Setup

Bachmann E-Z Command Dynamis Setup

Bachmann E-Z Command Dynamis Setup

Other documents