Garmin Bicicleta de entrenamiento Tacx NEO Bike Smart User manual

Page is loading ...

- 1 -

Dear athlete,

Congratulations! You are now the proud owner of the Tacx NEO Bike

Smart, the first fully equipped Smart bike trainer fused with a bike.

Since the launch of the NEO Smart, 4 years ago, our intention has

always been to create the best and most immersive indoor cycling

experience possible. Integrating a bike with NEO Smart technology

creates a whole new product typology that opened the doors to new

and unique features. This will significantly enhance your indoor

cycling experience. Get insprired by it’s possibilities and watch the

video on YouTube!

This manual explains the assembly and usage of this unique trainer.

Please consult the assembly card when assembling the trainer.

Enjoy your training and don’t forget to

#PushYourLimits!

The Tacx Team

- 2 -

EN

Parts list

A

A1

A2

A3

A4

A5

A6

A7

A8

B

B1

B2

B3

B4

FRAME

Bottle cage

Air grill

Disc

Front leg

Adjustable feet (left and right)

Crank

Rear leg

Wheels (left and right)

CONTROL PANEL

Air fans

Air fan knob (left and right)

Display

USB chargers

C

C1

C2

C3

C4

C5

C6

C7

C8

C9

D

D1

D2

D3

D4

D5

D6

HANDLEBARS

Handlebar cover

Handlebar rail

Handlebar distance bolt

Stem

Stem adjustment bolt

Control buttons

Brakes

Shifter big

Shifter small

SADDLE

Saddle

Saddle angle bolt

Saddle rail

Saddle distance bolt

Seat post

Seat post adjustment bolt

- 3 -

EN

SAVE THESE INSTRUCTIONS

Table of contents

1. Before you begin 4

1a. Important precautions 4

1b. Dimensions 6

1c. Clearance 7

1d. Guidelines for cycling posture 8

1e. Geometry set up 10

2. Assembly 12

3. Quick start guide 14

3a. Productvoorschriften 14

3b. Het display 16

3c. Instellingen 18

3d. Training starten 19

3e. Speciale functies 22

4. Maintenance 24

5. Troubleshooting 25

5. Troubleshooting 26

- 4 -

1. Before you begin

OPERATION

1. It is the responsibility of the owner to ensure

that all users of this trainer are adequately

informed of all warnings and precautions.

2. Do not operate the trainer if the trainer is not

working properly.

3. This trainer is designed for indoor and home

use only. If the trainer is used in any other

environment, the liability of Tacx expires. Do

not use this trainer in a commercial, rental,

or institutional setting.

4. Tests have revealed that the unit will not

overheat, even when subject to extreme

use. However, when subject to prolonged

and intensive use, the enclosure around the

brake may become very hot. Allow the brake

to cool down for 30 minutes after use before

touching it.

5. Place the trainer on a firm and level surface.

Do not place the trainer on any surface that

blocks air openings.

6. Never leave any objects on the trainer while

not in use.

7. Keep the power cord away from heated

surfaces.

8. Do not operate the trainer where aerosol

products are used or where oxygen is being

administered. The user is responsible to

ensure that the room is supplied with enough

fresh air to create a safe and healthy climate

for training.

9. Perspiration moisture and condensation

can harm the electronics. Do not use the

trainer in damp areas. Incorrect use and/or

maintenance will void the warranty.

10. Do not expose the product to water or

moisture. Take extra care to prevent water or

moisture from dripping in the air-grill in the

back frame.

11. Never insert any object into any opening on

the trainer.

12. The trainer operates on a 48 Vdc 90 Watt

external power adapter. Only use the external

power adapter that came with the trainer.

Use of another type or brand of external

power adapter may cause a dangerous

situation which could lead to personal injury

or damage of the equipment or even fire.

13. The trainer can be used without the external

power adapter, however the downhill

assistance will not function and the trainer

operates as long as the user cycles.

For your benefit, read this manual carefully before using the Smart bike. If you have questions after

reading this manual, please contact Tacx support (see the Tacx support card). To help us assist you,

please note the name of the product (front of this manual) and article number (backside of this manual)

before contacting us.

1a. Important precautions

- 5 -

EN

USE

14. Use the trainer only as described in this

manual.

15. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or persons

with pre-existing health problems.

16. This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

17. Never allow children under age 14 or pets

on or around the trainer. Children should be

supervised to ensure that they do not play

with the appliance.

18. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down and consult your physician if the

situation does not improve.

MAINTENANCE

24. Clean only with a dry cloth. Do not use cleaning

solvents or abrasives.

25. Clean the aluminium disc on the left side of the

trainer after each use with a moist cloth and

dry thoroughly.

26. Inspect and properly tighten all parts of the

trainer regularly.

27. DANGER: Always unplug the power cord

immediately after use, before cleaning

the trainer, and before performing the

maintenance and adjustment procedures

described in this manual. Never remove any

housing unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized service

representative only.

19. The trainer should not be used by persons

weighing more than 120kg (265lbs).

20. The temperature of the room should be

within 10°C - 30°C to ensure a proper climate

for training. The relative humidity should not

be more than 85%.

21. Wear appropriate exercise clothes when

using the trainer. Athletic support clothes

are recommended for both men and women.

Always wear cycling shoes. Never use

the trainer with bare feet, wearing only

stockings, or in sandals

22. Always turn off and unplug the trainer after

a training.

23. Keep clothing, fingers and hair away from

the rotating disc, air fans, crank and bottom

bracket.

- 6 -

1. Before you begin

1b. Dimensions

The maximum height of the NEO Bike Smart from the surface to the top of the fans is 1.35 m (4.43 ft).

The maximum length of NEO Bike Smart including the fans is 1.50 m (4.92 ft) and the width is 0.75

(2.5ft). See the images below, dimensions are displayed in millimeters.

1250 / 1500

750

1090 / 1350

- 7 -

EN

1c. Clearance

Place the trainer with at least 600 mm (23.6 in.) of clearance on the sides and back. See image below,

dimensions are displayed in millimeters.

600

- 8 -

1d. Guidelines for cycling posture

Below are guidelines for a correct cycling posture on the NEO bike. Please note, a correct cycling

posture is very personal and can vary between people.

150

o

- 155

o

4 - 10 cm

1.6 - 3.9 in

90

o

1. Before you begin

- 9 -

EN

SEAT HEIGHT

When you sit on the bike with your shoe on or in the pedal and press your leg fully downwards, your knee

should make an angle of 150 to 155 degrees. If this is not the case, change the height as follows:

1. Hold the saddle and loosen the seat post with the seat post adjustment bolt (D6).

2. Adjust the saddle height according to the mentioned requirements.

3. Tighten the seat post with bolt D6.

Please note, the maximum height of the seat is 26 cm (10.2 in), do not exceed this limit.

SEAT HORIZONTAL POSITION

When you sit on the bike with the crank arms horizontally (parallel to the floor), your knee should be

directly above the centre of the pedal. If this is not the case, change the horizontal position as follows:

1. Loosen the saddle rail with the saddle distance bolt (D4).

2. Adjust the horizontal position according to the mentioned requirements.

3. Tighten the saddle rail with bolt D4.

Please note, the maximum distance of the seat is 15 cm (5.9 in), do not exceed this limit.

If you need to move the saddle forwards or backwards severely, you may need to raise/lower the saddle

to compensate. Every time the saddle is moved forward the effective saddle height is reduced and vice

versa for moving the saddle backwards. If you move your saddle more than 1 cm recheck the saddle

height.

HANDLEBAR HEIGHT

Comfort dictates the appropriate height, so pick a position that minimizes strain on your back. Typically

the height is leveled with or slightly below the seat, with a maximum of 10 cm (3.9 in). Change the height

of the handlebars as follows:

1. Hold the handlebars and loosen the stem with the stem adjustment bolt (C5).

2. Adjust the height according to the mentioned requirements.

3. Tighten the stem with bolt C5.

Please note, the maximum height of the steer is 26 cm (10.2 in), do not exceed this limit.

HANDLEBAR HORIZONTAL POSITION

When you sit on the bike with your hands on top of the handlebars and your pedals parellel to the floor,

your elbow should be aligned with the inside of your knee and centre of the pedal. Or, you may opt to look

at the angle of your back which should be at least 45

o

parallel to the floor with an upper arm to torso

angle of 90

o

. If this is not the case, change the horizontal position of the handlebars as follows:

1. Loosen the handlebars with the handlebar distance bolt (C3).

2. Adjust the height according to the mentioned requirements.

3. Tighten the handlebars with the bolt C3.

Please note, the maximum distance of the steer is 15 cm (5.9 in), do not exceed this limit.

WARNING: Always dismount the NEO Bike before adjusting the saddle or handlebar height or positions.

- 10 -

1e. Geometry set up

The minimum and maximum dimensions of the height and horizontal positon of the saddle and

handlebars on the bike are shown in the image below. You can set them according to the geometry of

your road bike.

1. Before you begin

640 - 900 mm | 25.2 - 35.4 in

405 - 845 mm | 15.9 - 33.3 in

350 - 580 mm | 13.7 - 22.8 in

550 - 810 mm | 21.7 - 31.9 in

Page is loading ...

- 12 -

The NEO Bike is packed in the following parts:

1. T8001.50 Frame

2. T8003 Front leg (A4)

3. T8002 Rear leg (A7)

4. T8011.50 Saddle, mounted on rail (D1-D3)

5. T8010.50 Control panel with handlebars (B3, B4, C1-C3 & C6-C9)

6. T8010.51 Air fans (B1 & B2)

7. T8015.07 Rubber mat

8. T8010.16 Tablet mount

9. T8017 Gift box with bottle cage (A1)

10. T8015 Assembly box

Please assemble the trainer as instructed and with at least two persons. Consult the part list on page 2

and the assembly manual. First remove all packaging and check if everything is in the package.

A. MOUNT THE LEGS AND PLACE THE TRAINER

1. Place the bike on the floor and tilt it to the back or front to mount the legs.

Please carefully lift the trainer, it is heavy (50 kg).

2. Mount the front legs (A4) with the two bolts T8015.02 and T8015.03 and fix with an 8 mm allen key.

3. Mount the rear leg (A7) with the two bolts T8015.01 and fix with an 8 mm allen key.

4. Place the trainer on a firm, level surface. Please carefully lift the trainer, it is very heavy (50 kg).

5. Stabilize the trainer by leveling the front legs with the adjustable feet (A5).

a. Start with one side and turn the button left to shorten or to the right to lengthen the leg.

b. Do the same for the other side.

c. Continue until the bike stands completely stable on the floor.

B. MOUNT YOUR PEDALS

6. Select the needed pedal-insert, the left and right inserts differ (L = left, R = right)

7. Grease the insert.

8. Mount the pedal with the required insert onto the axle.

9. Fix the pedal by rotating it in the correct direction.

C. MOUNT THE BOTTLE CAGE

10. Mount the cage with an allen key 4 mm.

D. MOUNT THE SADDLE

11. Place the cap T8010.05 in the saddle rail (D3).

12. Slide the saddle (D1) on to the saddle rail (D3).

13. Fix the saddle on the required height and distance with bolts D6 (height) and D4 (distance) with a 6 and

8 mm allen key. Or replace the bolts by the handles T8015.15 and T8015.16. Max. height is 26 cm and

max. distance is 15 cm, please do not exceed this limit. Consult the correct posture on page 8.

14. Set the saddle angle with bolt D2 and a 5 mm allen key.

2. Assembly

When this icon is shown, the step is to be

conducted with at least two persons.

- 13 -

EN

E. MOUNT THE CONTROL PANEL AND HANDLEBARS

15. Place the cap T8010.05 in the handlebar rail (C2).

16. Mount the control panel and handlebars on the handlebar rail (C2). Make sure the cables remain free.

17. Fix the panel with a 6 mm allen key.

18. Set the handlebar height and distance with bolts C3 and C5 with a 6 and 8 mm allen key. Or replace the

bolts by the handles T8015.15 and T8015.16. Max. height is 26 cm and max. distance is 15 cm, please do

not exceed this limit. Consult the correct posture on page 8.

19. Adjust the angle of the handlebars, if desired:

a. Remove the handlebar cover (C1) with the Torx 20.

b. Remove the 4 screws.

c. Set the needed angle and fix the handlebars with the 4 screws.

d. Position the handlebar cover (C1) and fix with the Torx 20.

G. MOUNT THE AIR FANS OR TABLET MOUNT

Please note the air fans include a tablet mount.

20. Place the air fans (B1) or tablet mount (T8010.16) on the panel.

21. Fix the fans with the torx 20.

22. If desired, you can change the angle of the air fans with knob B2.

23. Position the power cables for the display and fans.

H. PLACE RUBBER MAT

24. Place the rubber mat on the phone surface.

J. PLACE YOUR TABLET

25. Position your tablet, if desired, and tighten with the rubber strip.

26. Plug the power cable of your tablet into the USB ports under the panel.

Tacx is not liable or responsible for damage caused to your devices due to incorrect mounting of the tablet holder.

K. CONNECT TO MAINS POWER

Choose to train with or without mains power. When not connected, it will generate its own energy and is

powered as long as it is cycled on. The NEO Bike Smart will have the same features and specifications

(except Descent Simulation) as it would have with a power supply connection.

OPTIONAL: Customize the bike by mounting your own saddle, handlebar tape or bottle cage as instructed

by the supplier. Please check the Tacx support website for instructions.

USE OF HANDLES: The handles T8015.15 and T8015.16 may be used to set the height and horizontal

position of the seat post and the saddle instead of a 6 and 8 mm allen key. This is especially handy when

you have to set this regularly; for example, when various persons use the NEO Bike. You can do so by

replacing the bolts; replace C5 and D6 by the T8015.16 and the C3 and D4 by the T8015.15.

- 14 -

3. Quick start guide

3a. Product regulations

The NEO Bike Smart is pushing everything we know about indoor cycling to the next level. Designed to

create an unprecedented, unique and immersive experience. The combination of its unique features

like road feel, gear feel, virtual gears, air fans, dynamic inertia and downhill drive makes cycling

indoors surprisingly realistic and fun. With customizable bike parts it even feels like cycling on your

road or tri bike. Completely silent, an integrated display, programmable control buttons, phone and

tablet holder are all enabling an easy way of using your preferred applications. The NEO Bike Smart is

a complete plug and play indoor cycling experience.

Specifications

• Control: Automatic or manual

• Software: Tacx software & third party software

• Communication: ANT+ FE-C & Bluetooth open protocol

• Max. incline realistic up to 25%

• Max. resistance: 2200 Watts

• Max. torque: 85 Nm

• Max. brake force: 250 N

• Accuracy: within 1%

• Completely silent

Intended use

The trainer is intended for a maximum user weight of 120kg (265lbs).

Use cues

The meaning of the following use cues are:

1. Cycling power indicator

A spot on the floor changes colour from blue to red when cycling with a higher power.

2. Display indicator

Display shows various data and user information. See 3b on page 16.

- 15 -

EN

IMPORTANT Please download the free Tacx Utility app from the App store or Google Play

and connect the NEO Bike Smart before first use. This app is used to update the trainer,

change the gear ratio, check your connections and analyze issues if needed.

EN

- 16 -

3. Quick start guide

For your benefit, read this manual carefully before using the Smart bike. If you have questions after

reading this manual, please contact Tacx support (see the Tacx support card). To help us assist you,

please note the name of the product (front of this manual) and article number (backside of this manual)

before contacting us.

3b. The display

When cycling on on the NEO Bike, the display will automatically turn on. The display differs when

connected to software or when training stand alone. If the display doesn’t turn on, please contact Tacx

support.

Error/Update

indicator

ERROR UPDATE

%

bpm rpm

km/h Watt 3”5”10”30”

Watt

mi/h

ANT+/Bluetooth

indicators

Power

Speed

Heart rate

Front gears

Cassette

Cadence

Training mode

- 17 -

EN

If these icons are shown, this means the following:

ANT+/Bluetooth indicators

ANT+ indicator: is shown when you’re connected to another device via ANT+.

Bluetooth indicator: is shown when you’re connected to another device via Bluetooth.

Error/Update indicator

ERROR indicator: is shown when an error has occurred in the trainer. Connect the trainer to the Tacx

Utility app for more information on the type of error and contact Tacx support if you cannot resolve it

yourself.

UPDATE indicator: is shown when you have selected to update the trainer’s firmware in the Tacx Utility

app. You cannot use the trainer at this time.

We suggest to regularly check if an update is available for your trainer with the Tacx Utility App. Please

follow these steps to check for updates and to update your trainer:

1. Open the Tacx Utility app.

2. Go to Devices and connect the NEO Bike (via Bluetooth).

3. Go to Update and check for an update.

This check may take a little while and the app will indicate if a newer version is available. If you choose

to update your trainer with this new firmware, please continue to step 4.

4. Press “update” to update your trainer.

The UPDATE indicator on the display is shown. Make sure the process has been fully completed before

continuing, this make take a couple of minutes.

5. Close the app and continue with your training.

Please contact Tacx support if the icon keeps being shown or the update has failed.

Speed

The current speed you’re cycling with in km/h or mph. You can switch metrics via the control buttons and

shifters, see page 18.

Power

Your power in wattage; this can be set in different modes via the control buttons and shifters, see page 18:

- Live power

- Average over last 3 seconds (3”)

- Average over last 5 seconds (5”)

- Average over last 10 seconds (10”)

- Average over last 30 seconds (30”)

Cadence

Your cadence in rpm.

- 18 -

Front gears

Current setting of the front gears. You can switch the front gears by pressing the left shifters. Gear up

with the big shifter (C8) or down with the small shifter (C9).

Cassette

Current setting of the cassette (rear gears). You can adjust the rear gears by pressing the right shifters.

Gear up with the big shifter (C8) or down with the small shifter (C9).

Training mode

When you’re cycling in stand alone mode (without any software), this field shows the mode you’re

training with. You can set the required mode as described in 3c. There are three modes:

1. Simulation mode

Train based on a fixed incline; this can be set by pressing the control buttons (C6).

The virtual shifters (C8 and C9) are enabled.

2. Power(erg) mode

Train based on a fixed power value; this can be set with the control buttons (C6).

3. Resistance mode

Train with predefined resistance levels (10). Switching between levels can be done with the control

buttons (C6).

3c. Settings

You can change the settings (metrics, average power settings and training mode) of the NEO Bike by

the control buttons (C6) and the shifters (C8 and C9).

Do so as follows:

1. Press the control buttons (C6) for 3 seconds. The modes on the display will blink.

2. Press the small shifter (C9) on the right side to select which term you wish to change.

3. Press the big shifter (C8) on the right side to change the selected term.

4. Confirm the setting by pressing the small shifter (C9) on the right.

5. Start training.

6. Change the set incline/power/resistance position by the handlebar buttons.

3. Quick start guide

- 19 -

EN

3. Quick start guide

3d. Start training

The NEO Bike Smart can be controlled in various ways:

1. By software and applications

a. Tacx apps

i. Tacx Training app (iOS/Android)

ii. Tacx Desktop app (Mac/Windows)

b. Software of third parties

2. Stand alone

In this mode, the trainer is not connected to any software or app. You control the resistance by the

control buttons (C6) and various modes are available:

a. Simulation mode: based on inclination gradient

The virtual shifters (C8 and C9) are enabled.

b. Power(erg) mode: based power (wattage)

c. Resistance mode: based on 10 predefined resistance positions

Train with software

The NEO Bike Smart can be controlled automatically by the Tacx Training app, Tacx Desktop app and

that of third parties like Zwift and TrainerRoad.

To start riding with software, please take the following steps:

1. If required, plug the Smart bike into the wall socket.

Please note: there is no power switch.

2. Download and install the app and/or software you wish to use.

3. Enable ANT+ or Bluetooth, depending on which device and app you’re using.

4. Connect the trainer to your device. The device is connected if the ANT+ or Bluetooth indicator on

the display is shown.

- 20 -

Tacx Training app (TTA)

Proceed with the following steps if you wish to

ride with the TTA:

1. Open the app.

2. Create an account or login if you’re already

registered*.

3. Connect the trainer via Bluetooth:

a. Enable Bluetooth.

b. Go to Set-up Connection in the app.

c. Search for the NEO Smart bike.

d. Select and connect the trainer.

e. Press “next”.

f. Connect a 2

nd

device if desired.

*If you wish to make use of Films, GPS rides and structured workouts, please subscribe to Premium.

4. Go to Workouts, select the training and press

the play button.

5. Stop cycling if you wish to pause your training.

6. Press stop if you wish to end it.

Your training is automatically stored as an

activity and is available to your friends (if set).

Tacx Desktop app (TDA)

Proceed with the following steps if you wish to

ride with the TDA:

1. Open the app.

2. Create an account or login if you’re already

registered*.

3. Connect the trainer via Bluetooth:

a. Enable Bluetooth.

b. Go to Devices in the app.

c. Search for the NEO Smart bike.

d. Select and connect the trainer.

e. Connect a 2

nd

device if required.

4. Go to Workouts, select the training and press

the play button.

5. Stop cycling if you wish to pause your training.

6. Press Escape (ESC) if you wish to end it.

Your training is automatically stored as an

activity and is available to your friends (if set).

Tacx software

The Tacx software consists of the Tacx Training app for smartphones and tablets, Tacx Desktop app for

Mac and Windows computers and the cloud website where you download and create your workouts,

analyse your activities and follow your friends.

- 21 -

Other software

Proceed with the following steps if you wish to ride with software of a third party:

1. Open the app.

2. Follow the instructions provided by the app.

3. Connect the trainer via ANT+ or Bluetooth.

4. Connect a second device if required.

5. Select the training of your choice and start training!

Train stand alone

You may opt to train without a device as follows:

1. Set the preferred mode and settings.

You can change the metrics, average power setting or training mode, see page 18.

2. Start training.

3. Change the set incline/power/resistance position by the handlebar buttons.

CONNECT A HEART RATE MONITOR: The trainer will automatically connect to your heart rate monitor.

Make sure you stand closely to the trainer as it connects automatically to the nearest monitor.

Page is loading ...

Garmin Bicicleta de entrenamiento Tacx NEO Bike Smart User manual

Garmin Bicicleta de entrenamiento Tacx NEO Bike Smart User manual

in other languages

Related papers

Other documents