Bull Power6 - 7214 Model 1U2 Storage Device Enclosure Installation guide

7214 Model 1U2

Storage Device

Enclosure

Setup and Operation

Guide

ESCALA

REFERENCE

86 A1 70EW 00

ESCALA

7214 Model 1U2 Storage

Device Enclosure

Setup and Operation Guide

Hardware

March 2008

BULL CEDOC

357 AVENUE PATTON

B.P.20845

49008 ANGERS CEDEX 01

FRANCE

REFERENCE

86 A1 70EW 00

The following copyright notice protects this book under Copyright laws which prohibit such actions as,

but not limited to, copying, distributing, modifying, and making derivative works.

Printed in France

Suggestions and criticisms concerning the form, content, and presentation of this

book are invited. A form is provided at the end of this book for this purpose.

To order additional copies of this book or other Bull Technical Publications, you

are invited to use the Ordering Form also provided at the end of this book.

Trademarks and Acknowledgements

We acknowledge the rights of the proprietors of the trademarks mentioned in this manual.

All brand names and software and hardware product names are subject to trademark and/or patent

protection.

Quoting of brand and product names is for information purposes only and does not represent trademark

misuse.

The information in this document is subject to change without notice. Bull will not be liable for

errors contained herein, or for incidental or consequential damages in connection with the use of

this material.

Contents

Notices . . . . . . . . . . . . . . .v

Safety and Environmental Notices . . . . . . .vi

Danger Notices . . . . . . . . . . . .vi

Caution Notices . . . . . . . . . . . .vi

Attention Notices . . . . . . . . . . . vii

Electronic Emission Notices . . . . . . . . . vii

Federal Communications Commission (FCC)

statement . . . . . . . . . . . . . . vii

Product recycling and disposal . . . . . . . .ix

Battery return program . . . . . . . . . . .x

IBM Cryptographic Coprocessor Card Return

Program . . . . . . . . . . . . . . . xii

Trademarks . . . . . . . . . . . . . . xii

About This Guide . . . . . . . . . . xiii

Related Publications . . . . . . . . . . . xiv

How to send your comments . . . . . . . . xiv

Chapter 1. General Information . . . . .1

System Requirement . . . . . . . . . . . .3

Ownership Requirements . . . . . . . . . .3

Specifications . . . . . . . . . . . . . .4

Media Drive Environment and Use . . . . . . .5

Media Grades . . . . . . . . . . . . .5

Media Handling and Storage . . . . . . . .5

Environmental Issues . . . . . . . . . .5

Drive Cleaning . . . . . . . . . . . .5

SAS Hardware Issues . . . . . . . . . .6

Microcode Updates . . . . . . . . . . .6

Summary . . . . . . . . . . . . . .6

Chapter 2. Installing and Removing

Device Features . . . . . . . . . . .7

Laser Safety Information . . . . . . . . . .7

Handling Static-Sensitive Devices . . . . . . .7

Feature Code Devices and Recommendations . . .8

Preparing the 7214 Storage Enclosure for Device

Removal or Installation . . . . . . . . . . .9

Removing a Storage Device from the Enclosure . .10

Removing a DVD Drive from the DVD Assembly 10

Removing the DAT72 Drive Assembly . . . .11

Removing the Bay Blank Assembly . . . . .12

Removing and Replacing other Enclosure

Components . . . . . . . . . . . . . .13

Removing and Replacing the Power Supply . .13

Removing and Replacing the Cooling Fan . . .15

Chapter 3. Mounting the 7214 Storage

Enclosure in a Rack . . . . . . . . .17

Chapter 4. Attaching the 7214 Storage

Enclosure to a Host System

(Installation) . . . . . . . . . . . .19

Performing the Installation . . . . . . . . .19

Step 1. Using the Inventory Checklist . . . . .19

Step 2. Checking the Electrical Outlets . . . .20

Step 3. Assembling the Materials . . . . . .20

Step 4. Placing the 7214 Storage Enclosure . . .20

Step 5. Connecting the SAS Cable . . . . . .21

Step 6. Connecting the Power Cables . . . . .21

Step 7. Performing the Checkout Procedure . . .22

Chapter 5. Removing the 7214 Storage

Enclosure from a Host System . . . .25

Removal Checklist . . . . . . . . . . . .25

Chapter 6. The DAT 72, 4mm Tape

Drive Feature . . . . . . . . . . . .27

Feature Kit Contents . . . . . . . . . . .28

Operation Features . . . . . . . . . . . .29

Unload Button . . . . . . . . . . . .29

Status Lights . . . . . . . . . . . . .29

Rear View of the DAT 72 Drive . . . . . . . .32

Loading and Unloading a Tape Cartridge . . . .32

Loading a Tape Cartridge . . . . . . . . .32

Unloading a Tape Cartridge . . . . . . . .33

Emergency Eject Feature . . . . . . . . .33

Cleaning the Tape Drive . . . . . . . . . .33

Types of Tape Cartridges . . . . . . . . . .35

Recommendations for Data Cartridge Usage . . .36

Storage and Shipping Environments . . . . . .37

Tape Cartridge Storage . . . . . . . . .38

Operating in Harsh Environments . . . . . . .38

Prolonging Head Life . . . . . . . . . . .38

Data Cartridge Erasure . . . . . . . . . .38

Setting the Write-Protect Switch . . . . . . .39

Ordering Tape Cartridges . . . . . . . . . .39

Chapter 7. The DVD Drive Features . .41

Feature Kit Contents . . . . . . . . . . .43

Operator Controls . . . . . . . . . . . .44

Load/Unload Button . . . . . . . . . .44

Fault LED . . . . . . . . . . . . . .44

Status Lights . . . . . . . . . . . . .44

Rear View of the DVD Drive Assembly . . . . .45

Loading and Unloading a DVD Disc . . . . . .45

Loading a DVD . . . . . . . . . . . .45

Unloading a Disc . . . . . . . . . . .46

Ordering DVD Discs . . . . . . . . . . .46

Recommendations for Disc Usage . . . . . . .46

Storage and Shipping Environments . . . . . .47

Appendix. Power Cables . . . . . . .49

iv 7214 Storage Device Enclosure Setup and Operator Guide

Notices

This information was developed for products and services offered in the U.S.A.

IBM may not offer the products, services, or features discussed in this document in

other countries. Consult your local IBM representative for information on the

products and services currently available in your area. Any reference to an IBM

product, program, or service is not intended to state or imply that only that IBM

product, program, or service may be used. Any functionally equivalent product,

program, or service that does not infringe any IBM intellectual property right may

be used instead. However, it is the user’s responsibility to evaluate and verify the

operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter

described in this document. The furnishing of this document does not grant you

any license to these patents. You can send license inquiries, in writing, to:

IBM Director of Licensing

IBM Corporation

North Castle Drive

Armonk, NY 10504-1785

U.S.A.

For

license inquiries regarding double-byte (DBCS) information, contact the IBM

Intellectual Property Department in your country or send inquiries, in writing, to:

IBM

World Trade Asia Corporation

Licensing

2-31 Roppongi 3-chome, Minato-ku

Tokyo 106-0032, Japan

The

following paragraph does not apply to the United Kingdom or any other

country where such provisions are inconsistent with local law:

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS

PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or

implied warranties in certain transactions, therefore, this statement may not apply

to you.

This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be

incorporated in new editions of the publication. IBM may make improvements

and/or changes in the product(s) and/or the program(s) described in this

publication at any time without notice.

Any references in this information to non-IBM Web sites are provided for

convenience only and do not in any manner serve as an endorsement of those Web

sites. The materials at those Web sites are not part of the materials for this IBM

product and use of those Web sites is at your own risk.

IBM may use or distribute any of the information you supply in any way it

believes appropriate without incurring any obligation to you.

Any performance data contained herein was determined in a controlled

environment. Therefore, the results obtained in other operating environments may

vary significantly. Some measurements may have been made on development-level

systems and there is no guarantee that these measurements will be the same on

generally available systems. Furthermore, some measurements may have been

estimated through extrapolation. Actual results may vary. Users of this document

should verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers of

those products, their published announcements or other publicly available sources.

IBM has not tested those products and cannot confirm the accuracy of

performance, compatibility or any other claims related to non-IBM products.

Questions on the capabilities of non-IBM products should be addressed to the

suppliers of those products.

All statements regarding IBM’s future direction or intent are subject to change or

withdrawal without notice, and represent goals and objectives only.

This information contains examples of data and reports used in daily business

operations. To illustrate them as completely as possible, the examples include the

names of individuals, companies, brands, and products. All of these names are

fictitious and any similarity to the names and addresses used by an actual business

enterprise is entirely coincidental.

If you are viewing this information softcopy, the photographs and color

illustrations may not appear.

The drawings and specifications contained herein shall not be reproduced in whole

or in part without the written permission of IBM.

IBM has prepared this publication for use with the specific machines indicated.

IBM makes no representations that it is suitable for any other purpose.

IBM’s computer systems contain mechanisms designed to reduce the possibility of

undetected data corruption or loss. This risk, however, cannot be eliminated. Users

who experience unplanned outages, system failures, power fluctuations or outages,

or component failures must verify the accuracy of operations performed and data

saved or transmitted by the system at or near the time of the outage or failure. In

addition, users must establish procedures to ensure that there is independent data

verification before relying on such data in sensitive or critical operations. Users

should periodically check IBM’s support Web sites for updated information and

fixes applicable to the system and related software.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

vi 7214 Storage Device Enclosure Setup and Operator Guide

Attention Notices

An attention notice indicates the possibility of damage to a program, device,

system, or data.

Electronic Emission Notices

The following Statement applies to this IBM product. The statement for other IBM

products intended for use with this product will appear in their accompanying

manuals.

Federal Communications Commission (FCC) statement

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference, in which case the user will be required to correct the

interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to

meet FCC emission limits. IBM is not responsible for any radio or television

interference caused by using other than recommended cables and connectors or by

unauthorized changes or modifications to this equipment. Unauthorized changes

or modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Responsible Party:

International Business Machines Corporation

New Orchard Road

Armonk, NY 10504

Telephone: 1-919-543-2193

Industry Canada Compliance Statement

This Class A digital apparatus meets the requirements of the Canadian

Interference-Causing Equipment Regulations.

Avis de conformité à la réglementation d’Industrie Canada

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement

sur le matériel brouilleur du Canada.

European Community Compliance Statement

This product is in conformity with the protection requirements of EU Council

Directive 89/336/EEC on the approximation of the laws of the Member States

relating to electromagnetic compatibility. IBM cannot accept responsibility for any

Notices vii

failure to satisfy the protection requirements resulting from a non-recommended

modification of the product, including the fitting of non-IBM option cards.

Australia and New Zealand Class A statement

Attention: This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate

measures.

VCCI Statement - Japan

The following is a summary of the VCCI Japanese statement in the box above.

This is a Class A product based on the standard of the Voluntary Control Council

for Interference by Information Technology Equipment (VCCI). If this equipment is

used in a domestic environment, radio disturbance may arise. When such trouble

occurs, the user may be required to take corrective actions.

Electromagnetic Interference (EMI) Statement - People’s Republic of China

Per GB 9254–1998, the user manual for a Class A product must carry the following

warning message (English translation from the Chinese standard) about use in a

residential environment in Chinese (Simplified Chinese):

Declaration: This is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may need to perform practical

action.

Electromagnetic Interference (EMI) Statement - Taiwan

The following is a summary of the EMI Taiwan statement above.

Warning: This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user will be required to take adequate

measures.

viii 7214 Storage Device Enclosure Setup and Operator Guide

Radio Protection for Germany

Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom

9.Nov.92 das EG–Konformitätszeichen zu führen.

Der Aussteller der Konformitätserklärung ist die IBM Germany.

Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese von

Geräten gilt folgende Bestimmung nach dem EMVG:

Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit

besonderer Genehmigung des Bundesministers für Post und Telekommunikation

oder des Bundesamtes für Post und Telekommunikation betrieben werden. Die

Genehmigung wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten

sind.

(Auszug aus dem EMVG vom 9.Nov.92, Para.3, Abs.4)

Hinweis

Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht

veröffentlicht worden.

Product recycling and disposal

This unit must be recycled or discarded according to applicable local and national

regulations. IBM encourages owners of information technology (IT) equipment to

responsibly recycle their equipment when it is no longer needed. IBM offers a

variety of product return programs and services in several countries to assist

equipment owners in recycling their IT products. Information on IBM product

recycling offerings can be found on IBM’s Internet site at http://www.ibm.com/

ibm/environment/products/index.shtml

Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la

normativa nacional o local aplicable. IBM recomienda a los propietarios de equipos

de tecnología de la informaci¾n (TI) que reciclen responsablemente sus equipos

cuando éstos ya no les sean ·tiles. IBM dispone de una serie de programas y

servicios de devoluci¾n de productos en varios países, a fin de ayudar a los

propietarios de equipos a reciclar sus productos de TI. Se puede encontrar

informaci¾n sobre las ofertas de reciclado de productos de IBM en el sitio web de

IBM http://www.ibm.com/ibm/environment/products/index.shtml.

Note: This mark applies only to countries within the European Union (EU) and

Norway

Notices ix

Appliances are labeled in accordance with European Directive 2002/96/EC

concerning waste electrical and electronic equipment (WEEE). The Directive

determines the framework for the return and recycling of used appliances as

applicable throughout the European Union. This label is applied to various

products to indicate that the product is not to be thrown away, but rather

reclaimed upon end of life per this Directive.

Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne

et à la Norvège.

L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de

Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les

dispositions de retour et de recyclage applicables aux systèmes utilisés à travers

l’Union européenne. Conformément à la directive, ladite étiquette précise que le

produit sur lequel elle est apposée ne doit pas être jeté mais être récupéré en fin de

vie.

In accordance with the European WEEE Directive, electrical and electronic

equipment (EEE) is to be collected separately and to be reused, recycled, or

recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the

WEEE Directive, as shown above, must not dispose of end of life EEE as unsorted

municipal waste, but use the collection framework available to customers for the

return, recycling and recovery of WEEE. Customer participation is important to

minimize any potential effects of EEE on the environment and human health due

to the potential presence of hazardous substances in EEE. For proper collection and

treatment, contact your local IBM representative.

Battery return program

This product may contain sealed lead acid, nickel cadmium, nickel metal hydride,

lithium, or lithium ion battery. Consult your user manual or service manual for

specific battery information. The battery must be recycled or disposed of properly.

Recycling facilities may not be available in your area. For information on disposal

of batteries outside the United States, go to http://www.ibm.com/ibm/

environment/products/index.shtml or contact your local waste disposal facility.

In the United States, IBM has established a return process for reuse, recycling, or

proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal

hydride, and other battery packs from IBM Equipment. For information on proper

disposal of these batteries, contact IBM at 1-800-426-4333. Please have the IBM part

number listed on the battery available prior to your call.

In the United States, IBM has established a return process for reuse, recycling, or

proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal

hydride, and other battery packs from IBM Equipment. For information on proper

disposal of these batteries, contact IBM at 1-800-426-4333. Please have the IBM part

number listed on the battery available prior to your call.

In Taiwan, the following applies. Please recycle batteries.

x 7214 Storage Device Enclosure Setup and Operator Guide

For the European Union (EU):

Note: This mark applies only to countries within the European Union (EU).

Batteries or packaging for batteries are labeled in accordance with European

Directive 2006/66/EC concerning batteries and accumulators and waste batteries

and accumulators. The Directive determines the framework for the return and

recycling of used batteries and accumulators as applicable throughout the

European Union. This label is applied to various batteries to indicate that the

battery is not to be thrown away, but rather reclaimed upon end of life per this

Directive.

Les batteries ou emballages pour batteries sont étiquetés conformément aux

directives européennes 2006/66/EC, norme relative aux batteries et accumulateurs

en usage et aux batteries et accumulateurs usés. Les directives déterminent la

marche à suivre en vigueur dans l’Union Européenne pour le retour et le recyclage

des batteries et accumulateurs usés. Cette étiquette est appliquée sur diverses

batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt

récupérée en fin de cycle de vie selon cette norme.

In accordance with the European Directive 2006/66/EC, batteries and accumulators

are labeled to indicate that they are to be collected separately and recycled at end

of life. The label on the battery may also include a chemical symbol for the metal

concerned in the battery (Pb for lead, Hg for mercury and Cd for cadmium). Users

of batteries and accumulators must not dispose of batteries and accumulators as

unsorted municipal waste, but use the collection framework available to customers

for the return, recycling and treatment of batteries and accumulators. Customer

participation is important to minimize any potential effects of batteries and

accumulators on the environment and human health due to the potential presence

of hazardous substances. For proper collection and treatment, contact your local

IBM representative.

For California:

Perchlorate Material - special handling may apply. See http://www.dtsc.ca.gov/

hazardouswaste/perchlorate.

The foregoing notice is provided in accordance with California Code of

Regulations Title 22, Division 4.5 Chapter 33. Best Management Practices for

Perchlorate Materials. This product, part or both may include a lithium manganese

dioxide battery which contains a perchlorate substance.

Notices xi

IBM Cryptographic Coprocessor Card Return Program

This machine may contain an optional feature, the cryptographic coprocessor card

which includes a polyurethane material that contains mercury. Please follow Local

Ordinances or regulations for disposal of this card. IBM has established a return

program for certain IBM Cryptographic Coprocessor Cards. More information can

be found at: http://www.ibm.com/ibm/environment/products/prp.shtml

Trademarks

The following terms are trademarks of International Business Machines

Corporation in the United States, or other countries, or both:

AIX

e (Stylized)

eServer

IBM

pSeries

RISC System/6000

RS/6000

System p

Other company, product, and service names may be the trademarks or service

marks of others.

xii 7214 Storage Device Enclosure Setup and Operator Guide

About This Guide

This guide describes how to install and use the 7214 Model 1U2 Storage Enclosure.

It contains the following chapters:

Chapter 1, General Information, describes the 7214 Storage Enclosure, gives the

system requirement, discusses cables, and lists hardware specifications.

Chapter 2, Installing and Removing Device Features, describes step-by-step

instructions on how to physically install and remove the storage device features in

the 7214 Model 1U2 Storage Enclosure.

Chapter 3, Mounting the 7214 Storage Enclosure in a Rack, describes the steps

required to mount the 7214 Storage Enclosure in a rack system.

Chapter 4, Attaching the 7214 Storage Enclosure to a Host System, describes

step-by-step instructions on how to properly attach and configure the 7214 Model

1U2 Storage Enclosure to a host system.

Chapter 5, Removing the 7214 Storage Enclosure from a Host System, describes

how to remove the 7214 Storage Enclosure after it has been installed.

Chapter 6, The DAT 72, 4mm Tape Drive Feature, describes the 7214 Model 1U2

Storage Device Enclosure Feature #1400, the DAT 72, 4mm Tape Drive.

Chapter 7, The DVD Drive Features, describes the 7214 Model 1U2 Storage Device

Enclosure Feature #1420 and #1421, the DVD Drives.

The appendix, “Power Cables,” provides power cable information for different

countries.

Store this guide with your system manuals.

Related Publications

v 7214 Model 1U2 Storage Enclosure Service Guide , SA38-0801, provides service and

maintenance information for the 7214 Storage Enclosure.

v IBM Externally Attached Devices Safety Information SA26-2004, provides

translations of danger notices.

How to send your comments

Your feedback is important in helping to provide the most accurate and

high-quality information. If you have any comments about this book or any other

IBM documentation, fill out the readers’ comment form at the back of this book.

v If you prefer to send comments by mail, use the readers’ comment form with the

address that is printed on the back. If you are mailing a readers’ comment form

from a country other than the United States, you can give the form to the local

IBM branch office or IBM representative for postage-paid mailing.

v If you prefer to send comments by FAX, use either of the following numbers:

– United States, Puerto Rico, and Canada: 1-800-937-3430

– Other countries: 1-507-253-5192

v

If you prefer to send comments electronically, use the following e-mail address:

[email protected]

Be

sure to include the following:

v The name of the book.

v The publication number of the book.

v The page number or topic to which your comment applies.

xiv 7214 Storage Device Enclosure Setup and Operator Guide

Chapter 1. General Information

The storage enclosure is an external enclosure that provides convenient storage

expansion capabilities for select IBM eServer, pSeries, and System p computer

systems. The storage enclosure is designed to mount in 1 EIA Unit (1.75″) of a

standard 19-inch rack using the rack mount hardware kit. The design of the

storage enclosure allows for easy customer setup and installation. The storage

enclosure has two bays that can accommodate a combination of the following

storage device features:

v DAT 72, 4mm tape drive (Bay A or B)

v DVD assembly tray (Bay B only)

The DVD assembly tray can contain two of the following in any combination.

– DVD-ROM drive

– DVD-RAM drive

– DVD blank (to be used when only one DVD drive is installed)

v

Bay Blank (to be used to cover an empty bay when only one drive is installed in

the 7214 Storage Enclosure)

Figure 1 shows the 7214 Storage Enclosure with a DAT-72 4mm tape drive installed

in Bay A and a DVD assembly with two DVD drives installed in Bay B.

The 7214 Storage Enclosure has the following components on the front of the unit:

Status Lights

The following status lights are located on the right front of the enclosure:

v The Power-on light 4 is a green LED that is illuminated when the

7214 Storage Enclosure is powered on.

v The Fault light 3 is an amber LED that is illuminated when the 7214

Storage Enclosure requires service.

RLHS503-0

1

2

3

4

5

Figure 1. Front view of the storage enclosure

Power Switch

The power switch 5 is a push button switch that enables the power to be

turned on or off. Push and release the button to toggle power to the 7214

Storage Enclosure on and off.

Bay A Bay A, 1 on the left front of the 7214 Storage Enclosure (see Figure 1 on

page 1), can accommodate a single tape storage device or a bay blank.

Bay B Bay B, 2 on the right front of the 7214 Storage Enclosure (see Figure 1 on

page 1), can accommodate a single tape storage device, a DVD assembly

tray, or a bay blank.

The rear of the 7214 Storage Enclosure has the following components:

Power Cable Connector

The 7214 Storage Enclosure receives power through a cable connected to

the power cable connector 1.

Power Supply DC Fault Indicator

A power supply DC fault is indicated with this amber LED. 2.

Power Supply AC On Indicator

This green LED 3 indicates the presence of AC when lit.

Power In Good LED

The Power In Good green LED 4 indicates a +12V/+5V good voltage

level at the ESM card.

All Power Good LED

The All Power Good green LED 5 indicates a +12V/+5V/+3.3V/+2.2V

good voltage level at the ESM card.

ESM Card Fault LED

The ESM Card Fault amber LED 6 indicates an ESM card fault when lit.

SAS Link LED

The SAS Link green LED 7 indicates the SAS connection is in use when

lit.

SAS Cable Connector

The 7214 Storage Enclosure provides a rear mounted SAS Cable connector

8 for attaching the 7214 Storage Enclosure to the SAS host.

RLHSV504-0

1

2

3

4

10

5

6

7

8

9

Figure 2. Rear view of the 7214 Storage Enclosure

2 7214 Storage Device Enclosure Setup and Operator Guide

Fan Fault LED

The Fan Fault amber LED 9 indicates a fan fault when lit.

Cooling Fan

The 7214 Storage Enclosure utilizes one internal cooling fan to regulate the

internal temperature of the enclosure. Air exits the 7214 Storage Enclosure

at the cooling fan location (10).

Note:

To ensure proper operation, place the 7214 Storage Enclosure so that

the cooling fan exits at the rear of the enclosure and the air inlet

holes at the front of the enclosure have sufficient clearance to ensure

airflow.

System Requirement

The following sections describe the host system requirements for the 7214 Model

103 Storage Enclosure:

The 7214 Model 1U2 storage enclosure requires a host system platform with an

AIX operating system with one of the following (or higher) software levels

installed:

v Release level 5L for POWER V5.3 with the 5300-06 Technology Level and Service

Pack 4

v Release level 5L for POWER V5.3 with the 5300-07 Technology Level

v Release level V6.1 with Service Pack 1

The 7214 Model 1U2 storage enclosure also supports host systems using the

following Linux operating systems:

v SUSE Enterprise Server 10 SP1 for Power systems (or later,)

Note:

Refer to the 7214 Model 1U2 sales pages for current supported software

requirements.

For a list of supported processors and adapters, contact your IBM marketing

representative or business partner.

Ownership Requirements

The 7214 Model 1U2 Storage Enclosure is a precision instrument designed to meet

your highest data storage expectations. In purchasing this product you expect to be

able to configure and use it reliably. IBM strives to deliver to you a product that

meets this expectation. As with all mechanical devices, this product drive requires

more periodic maintenance and care than the electronics in your computer. And to

ensure a reliable operation of your enclosure, IBM also requires that it be installed

and used properly. The following list outlines several required actions that become

your responsibility in the ownership of this device, and if followed, can not only

increase its availability, but may positively affect your warranty:

v Install the enclosure in a clean environment

v Use only high-quality, data-grade media

v Ensure that the media is properly handled and stored

v Clean the installed storage devices regularly, as recommended

Chapter 1. General Information 3

Specifications

Table 1. Specifications for the storage enclosure

Physical Specifications

Width 439 mm (17.28 in.)

Depth 733 mm (28.85 in.)

Height 42.9 mm (1.69 in.)

Weight 11.79 kg (26 lb)

1

Power Specifications

kVA 0.047 @ 120 V AC

V AC 100 to 125, or 200 to 240

Hertz 50 to 60

Btu Maximum (watts) 205 Btu/hr (60 watts) @ 240 V AC

Power Factor 0.8 to 0.9

Altitude 2135 m (7000 ft)

Performance Specifications

Dependant on device, media type, and configuration.

Recommended Environment

Environmental Factor Operating Non-operating

Temperature 10 to 35°C

(50 to 95°F)

-40 to 65°C

(-40 to 149°F)

Relative Humidity

(noncondensing)

8 to 80% non-condensing 1 to 100% (excluding

rain)

Maximum Wet Bulb 23°C

(73°F)

23°C

(73°F)

1

Weight with two DAT72, 4mm tape drives installed and no rack slides.

4 7214 Storage Device Enclosure Setup and Operator Guide

Page is loading ...

Bull Power6 - 7214 Model 1U2 Storage Device Enclosure Installation guide

Bull Power6 - 7214 Model 1U2 Storage Device Enclosure Installation guide

Related papers

Other documents