Maxon GPT SERIES (2010 Release) Installation guide

Brand: Maxon

Model: GPT SERIES (2010 Release)

Category: Tin openers

Type: Installation guide

This manual is also suitable for

GPT SERIES (M08-33 Rev B August 2010)

Maxon GPT SERIES (2010 Release) offers a reliable and durable solution for loading and unloading tasks. With its compact design, this liftgate can be easily installed on a wide range of vehicles, making it suitable for businesses and individuals who need to transport heavy or bulky items. The GPT-25 model has a lifting capacity of 2,500 lbs. and is ideal for smaller vehicles, while the GPT-5 model can handle up to 5,000 lbs. for heavier loads.

M-08-33

REV. B

AUGUST 2010

INSTALLATION MANUAL

GPT-25, GPT-3, GPT-4 & GPT-5

TABLE OF CONTENTS

WARNINGS ...........................................................................................................................3

SAFETY INSTRUCTIONS ....................................................................................................3

STANDARD LIFTGATE COMPONENTS .............................................................................. 4

GPT-SERIES INSTALLATION PARTS BAGS ....................................................................... 5

VEHICLE REQUIREMENTS .................................................................................................6

STEP 1 - WELD EXTENSION PLATE TO VEHICLE ............................................................ 9

STEP 2 - WELD LIFTGATE TO VEHICLE ...........................................................................11

STEP 3 - RUN POWER CABLE ..........................................................................................15

STEP 4 - CONNECT POWER CABLE ................................................................................ 16

STEP 5 - INSTALL CONTROL SWITCH .............................................................................18

STEP 6 - CONNECT POWER CABLE TO BATTERY ......................................................... 21

STEP 7 - REMOVE LOCKING ANGLES & KNUCKLE BOLTS ...........................................22

STEP 8 - WELD PLATFORM OPENER TO LIFTGATE ...................................................... 23

STEP 9 - FINISH WELDING LIFTGATE TO VEHICLE ....................................................... 27

STEP 10 - ADJUST PLATFORM (IF REQUIRED) .............................................................. 28

STEP 11 - CHECKING HYDRAULIC FLUID .......................................................................30

STEP 12 - WELD DOCK BUMPERS TO LIFTGATE ........................................................... 32

STEP 13 - BOLT RUBBER BUMPERS TO LIFTGATE ....................................................... 34

STEP 14 - VEHICLE TAILLIGHT POSITIONING (IF REQUIRED) ......................................35

ATTACH DECALS ............................................................................................................... 36

TOUCHUP PAINT ...............................................................................................................38

SYSTEM DIAGRAMS .........................................................................................................39

PUMP & MOTOR SOLENOID OPERATION .......................................................................39

HYDRAULIC SCHEMATIC (POWER DOWN) .................................................................... 40

ELECTRICAL SCHEMATIC (POWER DOWN) ...................................................................41

OPTIONS ............................................................................................................................42

OPTIONAL LIFTGATE COMPONENTS ..............................................................................42

RECOMMENDED LIFTGATE POWER CONFIGURATION ................................................43

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

SAFETY INSTRUCTIONS

 Comply with all WARNING and instruction decals attached to the Liftgate.

 Keep decals clean and legible. If decals are illegible or missing, replace them. Free replacement

decals are available from Maxon Customer Service.

 Consider the safety and location of bystanders and location of nearby objects when operating the

Liftgate. Stand to one side of the platform while operating the Liftgate.

 Do not stand, or allow obstructions, under the platform when lowering the Liftgate. Be sure your

feet are clear of the Liftgate.





 Wear appropriate safety equipment such as protective eyeglasses, faceshield and clothing while

performing maintenance on the Liftgate and handling the battery. Debris from drilling and contact

with battery acid may injure unprotected eyes and skin.

 while installing Liftgate. Connect vehicle

battery power to the Liftgate only when installation is complete or as required in the installation

instructions.

 Do not allow untrained persons to operate the Liftgate.

• Be careful working by an automotive type battery. Make sure the work area is well ventilated and

there are no ames or sparks near the battery. Never lay objects on the battery that can short the

terminals together. If battery acid gets in your eyes, immediately seek rst aid. If acid gets on your

skin, immediately wash it off with soap and water.

• If an emergency situation arises (vehicle or Liftgate) while operating the Liftgate, release the con-

trol switch to stop the Liftgate.



Liftgates. See Operation Manual for operating safety requirements.

 Read and understand the instructions in this Installation Manual before installing Liftgate.

 Before operating the Liftgate, read and understand the operating instructions in Operation

Manual.

• A correctly installed Liftgate operates smoothly and reasonably quiet. The only noticeable noise

during operation comes from the power unit while the platform is raised and lowered. Listen for

scraping, grating and binding noises and correct the problem before continuing to operate Liftgate.

• If it is necessary to stand on the platform while operating the Liftgate, keep your feet and any

objects clear of the inboard edge of the platform. Your feet or objects on the platform can become

trapped between the platform and the Liftgate extension plate.

• Never perform unauthorized modications on the Liftgate. Modications may result in early failure

of the Liftgate and may create hazards for Liftgate operators and maintainers.





WARNING

• Recommended practices for welding on steel parts are contained in the current 

. Damage to Liftgate and/or vehicle, and

personal injury can result from welds that are done incorrectly.

WARNINGS

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

STANDARD LIFTGATE COMPONENTS

PUMP

ASSEMBLY



CAUTION



FIG. 4-1

NOTE: Make sure you have all components and parts before you start installing Liftgate.

Compare parts in the part box and each kit box with packing list enclosed in each

box. If parts and components are missing or incorrect, call:

Maxon Customer Service





EXTENSION

PLATE

OPENER ASSEMBLY

MAIN

ASSEMBLY











BOXED COMPONENTS





11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

GPT-SERIES INSTALLATION PARTS BAGS



NOMENCLATURE OR DESCRIPTION QTY. PART NUMBER

HEAT SHRINK TUBING, 3/4” X 1-1/2" LG. 1 253316-04

MOLDED SWITCH ASSEMBLY 1 264951-04

SHIM, 3-1/2” X 1-3/4” X 1/4” 2 264731

SHIM, 2-1/2” X 1” X 1/16” 2 264732



FLAT, 2-1/2" 1” X 1/8” 2 201999

FLAT, 5" X 4” X 3/8” 2 229295



COPPER LUG (2GA) 1 906497-02

SELF-TAPPING SCREW, 10-24 X 1” LG. 4 900057-5

CLAMP, #10 RUBBER LOOM 2 801681

FRAME CLIP, 1/2” X 1-3/8” 7 050079

DECAL & MANUAL KIT 1

282842-01 (GPT-25)

282843-01 (GPT-3)

282844-01 (GPT-4)

282845-01 (GPT-5)

A. INSTALLATION MANUAL 1 M-08-33

B. OPERATION MANUAL 1 M-08-34

C. MAINTENANCE MANUAL 1 M-08-35

D. DECALS -

282848-01 (GPT-25)

282848-02 (GPT-3)

282848-03 (GPT-4)

282848-04 (GPT-5)

FUSED POWER CABLE, 175 AMP, 38’ LG. 1 264422

RUBBER DOCK BUMPER KIT 1 203410

PLASTIC TIE, 8” LG. 1 905322-01



DOCK BUMPER ANGLE, 23-1/2” LG. 2 226856

BRACE ANGLE, LH 1 266019-01



BRACE ANGLE, RH 1 266019-02

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

VEHICLE REQUIREMENTS



FIG. 6-2

1. Check for correct clearances   on vehicle to prevent interfer-

ence between vehicle and Liftgate.



FIG. 6-1

12-9/16” TO 21-9/16”



46” MIN. BED HEIGHT

24-1/2”

13”-22”

14”



46” MIN. BED HEIGHT

NOTE: Make sure vehicle is parked on level ground while preparing vehicle and

installing Liftgate.



 

Maximum height is  (Unloaded). Minimum height is 46” (Loaded).

On vehicle bodies equipped with swing open doors, the extension plate

and vehicle body must be modied to install this Liftgate.

NOTE: Dimensions are provided as reference for tting Liftgate to vehicle body.



22-3/16

14”

33-11/16

36”

30-3/16

32-1/2”

13-3/4”

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

2. Fit the Liftgate to vehicle body by cutting

vehicle frame as shown in .

VEHICLE FRAME CUTOUT FOR PLATFORM CLEARANCE









6-1/4”

WOODEN SPACER

BODY FLOOR

BODY CROSS-

MEMBERS

LONG SILL



FRAME

PLATFORM CLEARANCE

CUTOUT AREA







REAR SILL

NOTE: See the next page for interference areas that can result from rear sills over 4”

in height.

11-3/4”











-



CAUTION

NOTE: The platform cutout area illustrated below is required to prevent vehicle

frame interference when platform is being stowed and unstowed. Truck

frame is shown. For trailers, refer to instructions supplied with trailer

mounting kit for Liftgate.





NOTE: The dimensions, illustrated below, are maximums except as indicated.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713



FRONT VIEW - REAR SILL MORE THAN 4” IN HEIGHT



FIG. 8-1

CENTER

LINE

40-1/2”

3. If the rear sill is over 4” in height, measure and mark the areas to be modied on the sill

as shown in FIG. 8-1. A side view of the interference areas is shown in FIG. 8-2.

2-1/2”



VEHICLE

FRAME

BODY

FRAME

40-1/2”

SIDE VIEW - REAR SILL MORE THAN 4” IN HEIGHT

FIG. 8-2

REAR SILL

6-3/4”



4”

REAR

SILL

4”

MEASURE “H”



“L”

NOTE: L= 3.75 x H

AREA TO

MODIFY



11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

STEP 1 - WELD EXTENSION PLATE TO VEHICLE

1. Center the extension plate on vehicle body. Before welding extension plate to vehicle

body, make sure top surface of extension plate is ush with oor of vehicle body. Weld

the extension plate to vehicle body sill as shown in  9-2.

4” LG. LOCATED ABOVE EACH

OF 3 RECTANGULAR TUBES





2” LG. CENTERED

BETWEEN 4” WELDS

4” LG.

EXTENSION PLATE WELDS - VIEWED FROM ABOVE

FIG. 9-1

SILL



1/4”

4” LG.

EXTENSION PLATE WELDS - VIEWED FROM UNDERNEATH

FIG. 9-2

SILL





GAP WHERE SHOWN

1/4”



EQUAL SPACING



1/4”



GAP WHERE SHOWN

1” GAP

CAUTION





11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

STRAP & SPACER WELDS





FIG. 10-1B

2. Place 2 temporary support straps (5” x 4” x 3/8”

ats from parts bag) on the extension plate as

shown in FIG. 10-1A. Also, put 2 temporary

spacers (2” x 1” x 1/8” ats from parts bag) be-

tween platform and extension plate as shown in

FIG. 10-1B. (Spacers keep 1/8” between plat-

form and extension plate while welding Liftgate

to vehicle frame.) Weld the straps and spacers

to extension plate .

STEP 1 - WELD EXTENSION PLATE TO VEHICLE -







1/4”

1/8” SPACER



TYP. SPACER







STRAP TO EXTENSION



SPACER & SUPPORT

STRAP TO EXTENSION



4”

EXTENSION

PLATE

SUPPORT

STRAPS

FIG. 10-1A

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

STEP 2 - WELD LIFTGATE TO VEHICLE

1. Remove split looms from mounting

plates . (Split looms will

be reinstalled later after nal weld-

ing.)

2. Unfold the platform and ipover .

PLATFORM & FLIPOVER UNFOLDED

FIG. 11-2

FIG. 11-1

SPLIT LOOMS

MOUNTING

PLATES

FLIPOVER



PLATFORM



MOUNTING

PLATES





11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713



3. Make sure hoist is

not being set up the

incorrect way 

. Place

a “C”-clamp on

each side of plat-

form as shown

in FIG. 12-1.

(Clamps prevent

hoist chain from slipping

off platform.) Place chain

all around platform 

.

INCORRECT WAY TO HOIST LIFTGATE

FIG. 12-2







CCORRECT WAY TO HOIST LIFTGATE

FIG. 12-1

CAUTION

4. Hoist the Liftgate.

Then, place oor jack

under main frame

. Jack the

Liftgate into position.

Make sure vehicle

oor is horizontal and



vertical .







PINS





HOIST CHAIN

MAIN FRAME

VEHICLE FLOOR



MOUNTING

PLATE

FLIPOVER

PLATFORM

HOIST CHAIN

FLIPOVER

C-CLAMP



NOTE: Ensure pins stay lined

up vertical (see illus-

tra-tion) while Liftgate

is being welded to

vehicle frame.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

Check if both mounting

plates line up with the ve-

hicle frame. If the mounting

plates do not line up,

remove the tack welds

from one mounting plate

. Make sure

Liftgate stays centered

on vehicle. Reposi-

tion the mounting plate

against vehicle frame.

Tack weld as shown in

FIG. 13-1. Repeat for

second mounting plate

(reposition and tack weld).















REPOSITIONING MOUNTING PLATE



FIG. 13-1

MAIN FRAME



MOUNTING

PLATE



-



WARNING





CAUTION

VEHICLE FRAME CUTOUT



CAUTION

To protect the original paint sys-







11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

NOTE: Weld both mounting plates to

vehicle frame before welding

mounting plates to main frame.

MOUNTING

PLATE

WELDING TO VEHICLE FRAME AND



FIG. 14-1

2” LG. 4 PLACES





6. Clamp both mounting

plates to vehicle frame.

Before welding, make sure

cutout in vehicle frame

does not block the 2 slot-

ted holes in mounting

plate . Weld

the mounting plates to

vehicle frame as shown

in FIG. 14-1. Next, weld

both mounting plates to

main frame .

Remove clamps.



MAIN FRAME





VEHICLE FRAME CUTOUT





11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

STEP 3 - RUN POWER CABLE











CAUTION



VEHICLE FRAME

18” - 24”

SPACING

CHARGE LINE TO

PUMP BOX OR

BATTERY BOX

FRONT OF VEHICLE

REAR OF VEHICLE

CHARGE LINE

TO VEHICLE

BATTERY

FRAME

CLIPS



FUSE

Install vehicle charge line by running the line along the inside of vehicle frame 

. Make sure 

end of cable is by the battery. Run the

charge line from vehicle battery to Liftgate pump box positive terminal. Use frame clips

(parts box item) and plastic ties (as required) from charge line kit to secure cable.

NOTE: Make sure cable is long enough to reach positive terminal on Liftgate pump box

without putting tension on the cable.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

2. On the bare wire end of fused power cable, keep enough length to attach copper ter-

minal lug and reach motor solenoid without putting tension on cable (after connection)

. Measure (if needed), and then cut excess cable from bare wire end of

cable. Put heatshrink tubing (parts bag item)  on the end of the cable and

leave room for terminal lug. Crimp copper terminal lug (parts bag item) on the fused

power cable and shrink the heatshrink tubing .

STEP 4 - CONNECT POWER CABLE

TYPICAL FUSED POWER CABLE ROUTING

FIG. 16-2A

FIG. 16-2B

COPPER

TERMINAL

LUG



TUBING

FIG. 16-2C

FUSED

POWER CABLE

1. Unbolt and remove pump cover

.

UNBOLTING PUMP COVER

FIG. 16-1

PUMP

COVER

CAP SCREWS



POWER UNIT



FLAT

WASHERS



HEX NUTS



LONG SIDE OF

HOLDER FLATS

BUTT AGAINST

COVER

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

3. Remove hex nut and lock washer

from battery power terminal on

the starter solenoid. Connect the

fused power cable to the starter

solenoid as shown in

1. Reinstall and tighten lock

washer and hex nut.

TYPICAL FUSED POWER

CABLE ELECTRICAL CONNECTION



NOTE: MAXON recommends using

dielectric grease on all electri-

cal connections.







CAUTION

NOTE: Do not remove at washer from

the battery power terminal.

FUSED

POWER CABLE

BATTERY

POWER TERMINAL

STARTER

SOLENOID

HEX NUT



WASHER



11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713



FIG. 18-1A

HOLE DRILLING TEMPLATE

FIG. 18-1B

1-3/4”



1. Drill one 3/4“ hole and two #21–size holes in

the vertical post on curb side of vehicle body as

shown in FIG. 18-1A. Use template shown in

FIG. 18-1B.

NOTE: Hydraulic lines and electrical lines

must run into pump box through

sealing grommets . To

ensure a good seal on hydraulic &

electrical lines, never cut the sealing

grommets.

2. Cut tie strap on coiled wiring harness

. Pull the wiring har-

ness through grommet on the pump

mounting plate .

FIG. 18-2

PUMP MOUNTING

PLATE

TIE

STRAP

WIRING

HARNESS

GROMMET

18”

VEHICLE BODY

VERTICAL POST



11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713



ROUTING CONTROL SWITCH WIRING

FIG. 19-1

3/4” HOLE

VEHICLE BODY

VERTICAL POST

WIRING HARNESS

PUMP BOX

NOTE: MAXON recommends using dielectric grease on all electrical connections.

3. Run wiring harness under

vehicle body 

and up

through inside of vertical

post. Pull control switch

wiring harness out the 3/4“

hole drilled in vertical post

. Connect the

control switch wiring to the

wiring harness as shown

in FIG. 19-2. Push ex-

tended wiring back into the

¾” hole in the vertical post

until control switch touches

the post. Attach control

switch to vertical post with

2 self-tapping screws

.

CONTROL SWITCH WIRING CONNECTIONS

FIG. 19-2

WHITE

GREEN



GREEN

RED



SELF-TAPPING

CONTROL SWITCH

DECAL



11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

CAUTION







4. Bolt on the pump cover as shown in

FIG. 20-1. Torque the 5/16”-18 cover

bolts from 10 to 14 lbs.-ft.



BOLTING ON PUMP COVER

FIG. 20-1

PUMP

COVER

CAP SCREWS



POWER UNIT



FLAT

WASHERS



HEX NUTS



LONG SIDE OF

HOLDER FLATS

BUTT AGAINST

COVER

Page is loading ...

Maxon GPT SERIES (2010 Release) Installation guide

Brand: Maxon

Model: GPT SERIES (2010 Release)

Category: Tin openers

Type: Installation guide

This manual is also suitable for

GPT SERIES (M08-33 Rev B August 2010)

Download PDF

report

Maxon GPT SERIES (2010 Release) Installation guide

This manual is also suitable for

Maxon GPT SERIES (2010 Release) Installation guide

Related papers

Other documents