FMI VTD-30PV-JHB Operating instructions

Brand: FMI

Model: VTD-30PV-JHB

Type: Operating instructions

This manual is also suitable for

INSTALLATION INSTRUCTIONS FOR

OF-RC (ON/OFF) REMOTE

CONVERSION KIT

For Millivolt Cascade Natural and

Propane/LP Gas Logs

(NOT A GAS CONVERSION KIT)

Save this manual for future reference

WARNING: This conversion kit shall be installed by a quali-

ed service agency in accordance with the manufacturer's

instructions and all applicable codes and requirements of the

authority having jurisdiction. The information on this instruction

must be followed to minimize the risk of re or explosion or to

prevent property damage, personal injury or death. The qualied

service agency performing this work assumes responsibility

for the proper conversion of this appliance with this kit.

WARNING: If the information in this manual is not followed

exactly, a re or explosion may result causing property dam-

age, personal injury or loss of life.

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage.

Refer to this manual for correct installation and operational

procedures. For assistance or additional information consult

a qualied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

TESTED AND

LISTED BY

APPROVED

ANSI Z21.60

CSA 2.26

PFS

USC

The OF-RC Kit contains the following:

•1 - On/Off Remote Control Kit 125243-01

•1 - Bracket 117074-01

•2 - Screw #8-32 X 1'' 11186

•2 - Screw HWH AB 10-16 M11084-26

•2 - Nut 8-32 Hex Zinc 11201

•1 - Instruction Manual 114370-04

www.fmiproducts.com

114370-04C2

OFF

12V

BATTERY

COMPARTMENT

KCAB

TNORF

SIGNAL

LIGHT

ON/OFF

BUTTONS

Figure 2 - Installing battery into Receiver

Figure 1 - Removing Face Plate

Figure 3 - Connecting Wire Terminals

Screws

Faceplate

Control

Valve

Gas Valve

12V Battery

Compartment

INSTALLATION

This OF-RC On/Off Remote Kit is designed to

be used on MV Cascade series VTD-18NV-

JHB, VTD-18PV-JHB, VTD-24NV-JHB, VTD-

24PV-JHB, VTD-30NV-JHB and VTD-30PV-

JHB. This can also be used on MV Cascade

series that has been converted to Hi-Lo knob

VTD-HLCN and VTD-HLCP.

Installation Items Needed

Before installing the kit, make sure you have

the items listed below.

• Phillips screwdriver

• Needle nose plier

• 5/16"socketoratheadscrewdriver

OF-RC Conversion Kit or Replacement

Instructions

1. Turn control knob to the OFF position,

and shut off gas supply to valve.

2. Remove 4 screws and face plate. See

Figure 1.

3. Disconnect manual switch terminals.

This switch will be replaced by OF-RC

remote kit. Discard disconnected switch

wires or position and secure to avoid

contacting with other connectors and

wires.

4. Install included 4 AA size 1.5V batteries

into receiver (see Figure 2).

5. Connect the "+" (positive) terminal of

receiver to TH terminal of gas valve and

the "-" (negative) terminal of receiver to

TPTH terminal of gas valve (see Figure

3).

6. Install included 12V battery into hand

held transmitter (see Figure 4).

7. Install receiver using included bracket

and screws (see Figure 5, page 3).

8. Install receiver cover plate by snapping

cover plate into receiver.

9. Mount cover plate to bracket using

screws and nuts provided with kit (see

Figure 5, page 3).

10. Reinstall faceplate and screws.

REMOTE

FFO

LEARN

ADJ.

Requires 4-AA 1.5V

alkaline batteries

Learning

button

Frequency

adjusting

access hole

Remote Receiver

Battery cover

slides on/off

Slide

Switch

REMOTE

OFF

Figure 4 - Installing Battery in Hand-Held

Remote Control Unit

www.fmiproducts.com

114370-04C 3

REMOTE

OFF

LEARN

ADJ.

LEARN

ADJ.

REMOTE

OFF

Screws to Secure

Receiver Cover Plate to

bracket with Hex-nuts

Snap in Receiver

Cover Plate Here

Hex-Nut

Screws

Receiver

Cover Plate

Faceplate

Bracket

Receiver

Gas Valve

Figure 5 - Installing Receiver Cover Plate

INSTALLATION

Continued

114370-04

Rev. C

12/11

2701 S. Harbor Blvd.

Santa Ana, CA 92704

1-866-328-4537

www.fmiproducts.com

NOTICE: You must light the pi-

lot before using the hand held

remote control unit. Refer to

Lighting Instructions in your

appliance owner’s manual.

1. Afterlighting,letpilotameburnforabout

one minute. Turn control knob to the ON

position.Adjust ame adjustment knob

anywhere between HI and LO on models

with Hi/Lo knob conversion. Slide selector

switch to the REMOTE position.

Note: Burners may light if hand-held

remote ON button was on when selector

switch was last turned off. You can now

turn the burners on and off with the hand-

held remote control unit.

IMPORTANT: Do not leave the selector

switch in the REMOTE or ON position

when the pilot is not lit. This will drain

the battery.

2. On/Off Operation: Hold control button

on hand-held remote until burner turns

on. Hold control button again until burner

turns off (see Figure 6). When turning

burners off, the pilot will remain lit.

OPERATING REMOTE

Figure 6 - ON/OFF Hand-Held Remote

Control Unit

OFF

12V

BATTERY

COMPARTMENT

KCAB

TNORF

SIGNAL

LIGHT

ON/OFF

BUTTONS

Signal Light

ON/OFF

Buttons

FMI VTD-30PV-JHB Operating instructions

Brand: FMI

Model: VTD-30PV-JHB

Type: Operating instructions

This manual is also suitable for

Download PDF

report

FMI VTD-30PV-JHB Operating instructions

This manual is also suitable for

FMI VTD-30PV-JHB Operating instructions

Related papers

Other documents