INSTALLATION INSTRUCTIONS FOR
OF-RC (ON/OFF) REMOTE
CONVERSION KIT
For Millivolt Cascade Natural and
Propane/LP Gas Logs
(NOT A GAS CONVERSION KIT)
Save this manual for future reference
WARNING: This conversion kit shall be installed by a quali-
ed service agency in accordance with the manufacturer's
instructions and all applicable codes and requirements of the
authority having jurisdiction. The information on this instruction
must be followed to minimize the risk of re or explosion or to
prevent property damage, personal injury or death. The qualied
service agency performing this work assumes responsibility
for the proper conversion of this appliance with this kit.
WARNING: If the information in this manual is not followed
exactly, a re or explosion may result causing property dam-
age, personal injury or loss of life.
WARNING: Improper installation, adjustment, alteration,
service or maintenance can cause injury or property damage.
Refer to this manual for correct installation and operational
procedures. For assistance or additional information consult
a qualied installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
TESTED AND
LISTED BY
APPROVED
ANSI Z21.60
CSA 2.26
PFS
®
USC
The OF-RC Kit contains the following:
•1 - On/Off Remote Control Kit 125243-01
•1 - Bracket 117074-01
•2 - Screw #8-32 X 1'' 11186
•2 - Screw HWH AB 10-16 M11084-26
•2 - Nut 8-32 Hex Zinc 11201
•1 - Instruction Manual 114370-04
www.fmiproducts.com
114370-04C2
ON
OFF
12V
BATTERY
COMPARTMENT
KCAB
TNORF
SIGNAL
LIGHT
ON/OFF
BUTTONS
Figure 2 - Installing battery into Receiver
Figure 1 - Removing Face Plate
Figure 3 - Connecting Wire Terminals
Screws
Screws
Faceplate
Control
Valve
Gas Valve
12V Battery
Compartment
INSTALLATION
This OF-RC On/Off Remote Kit is designed to
be used on MV Cascade series VTD-18NV-
JHB, VTD-18PV-JHB, VTD-24NV-JHB, VTD-
24PV-JHB, VTD-30NV-JHB and VTD-30PV-
JHB. This can also be used on MV Cascade
series that has been converted to Hi-Lo knob
VTD-HLCN and VTD-HLCP.
Installation Items Needed
Before installing the kit, make sure you have
the items listed below.
• Phillips screwdriver
• Needle nose plier
• 5/16"socketoratheadscrewdriver
OF-RC Conversion Kit or Replacement
Instructions
1. Turn control knob to the OFF position,
and shut off gas supply to valve.
2. Remove 4 screws and face plate. See
Figure 1.
3. Disconnect manual switch terminals.
This switch will be replaced by OF-RC
remote kit. Discard disconnected switch
wires or position and secure to avoid
contacting with other connectors and
wires.
4. Install included 4 AA size 1.5V batteries
into receiver (see Figure 2).
5. Connect the "+" (positive) terminal of
receiver to TH terminal of gas valve and
the "-" (negative) terminal of receiver to
TPTH terminal of gas valve (see Figure
3).
6. Install included 12V battery into hand
held transmitter (see Figure 4).
7. Install receiver using included bracket
and screws (see Figure 5, page 3).
8. Install receiver cover plate by snapping
cover plate into receiver.
9. Mount cover plate to bracket using
screws and nuts provided with kit (see
Figure 5, page 3).
10. Reinstall faceplate and screws.
REMOTE
NO
FFO
LEARN
ADJ.
Requires 4-AA 1.5V
alkaline batteries
Learning
button
Frequency
adjusting
access hole
Remote Receiver
Battery cover
slides on/off
Slide
Switch
ON
REMOTE
OFF
Figure 4 - Installing Battery in Hand-Held
Remote Control Unit
www.fmiproducts.com
114370-04C 3
REMOTE
OFF
LEARN
ADJ.
ON
LEARN
ADJ.
REMOTE
OFF
ON
Screws to Secure
Receiver Cover Plate to
bracket with Hex-nuts
Snap in Receiver
Cover Plate Here
Hex-Nut
Screws
Screws
Receiver
Cover Plate
Faceplate
Bracket
Receiver
Gas Valve
Figure 5 - Installing Receiver Cover Plate
INSTALLATION
Continued
114370-04
Rev. C
12/11
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com
NOTICE: You must light the pi-
lot before using the hand held
remote control unit. Refer to
Lighting Instructions in your
appliance owner’s manual.
1. Afterlighting,letpilotameburnforabout
one minute. Turn control knob to the ON
position.Adjust ame adjustment knob
anywhere between HI and LO on models
with Hi/Lo knob conversion. Slide selector
switch to the REMOTE position.
Note: Burners may light if hand-held
remote ON button was on when selector
switch was last turned off. You can now
turn the burners on and off with the hand-
held remote control unit.
IMPORTANT: Do not leave the selector
switch in the REMOTE or ON position
when the pilot is not lit. This will drain
the battery.
2. On/Off Operation: Hold control button
on hand-held remote until burner turns
on. Hold control button again until burner
turns off (see Figure 6). When turning
burners off, the pilot will remain lit.
OPERATING REMOTE
Figure 6 - ON/OFF Hand-Held Remote
Control Unit
ON
OFF
12V
BATTERY
COMPARTMENT
KCAB
TNORF
SIGNAL
LIGHT
ON/OFF
BUTTONS
Signal Light
ON/OFF
Buttons
-
1
-
2
-
3
-
4
FMI VTD-18PV-JHB Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
FMI VTD-18PV-JHB Owner's manual
-
-
FMI VTD-30N-JHB User manual
-
Desa Tech VTD-HLCN Owner's manual
-
-
-
-
-
FMI VTD-18N-PDG Owner's manual
-