AM16

Hobart AM16 User manual

  • Hello! I've analyzed the Daily Operation & Cleaning Guide for the Hobart AM16 warewasher. This document provides detailed instructions on how to use and maintain the machine, including daily operations, cleaning, and chemical replacement. I'm here to help answer any questions you have about its operation or maintenance.
  • How to start a wash cycle?
    What should I do when the machine shows SANITIZER EMPTY or DETERGENT EMPTY?
    How to drain remaining water from the tank?
    How to power off the machine?
    What should I do before loading dishes?
© 2021 Hobart 701 S. Ridge Avenue, Troy, OH 45373 | Phone: (888) 378-1338 | hobartcorp.com | Resource Center: hobartcorp.com/am16training F48539 (09/21)
PROPER RACKING
WILL PROVIDE THE BEST
CLEANING RESULTS.
PRE-SCRAP DISHES
USE COMMERCIAL
DISHMACHINE
CHEMICALS ONLY
Do not use any other chemicals
with the dishmachine. Use PPE
for handling.
DO NOT
OVERLOAD RACK
DELIME THE MACHINE
The unit will alert you
when deliming is required.
When prompted, follow the
instructions on the display.
Note: Delime instructions will vary
based on model. Scan QR code for
more information.
AM16 WAREWASHER | Daily Operation & Cleaning Guide
SCAN TO WATCH
DELIME VIDEO
hobartcorp.com/am16training
OPERATIONAL TIPS –
GET THE MOST OUT OF
YOUR DISHWASHER
DAILY
OPERATION DAILY CLEANING
1Place strainer and scrap basket into the
dishwasher. Make sure to line up arrows.
2Close the door. Push POWER button.
3When fill is complete, the
readout will display READY.
4Select the WASH CYCLE: 1, 2, 4, 6 minutes.
To load a dishrack, open the door
and slide the rack in the machine.
5Close the door, the machine will start
automatically. The PLAY button turns
blue, and a progress bar will appear
at the bottom of the screen.
6Once the screen shows a check mark
and reads CYCLE COMPLETED, the
dishrack may be removed.
7To power off machine and drain, hold the
POWER button down for 5 seconds.
Wash Cycle
Wash
Rinse
Condense
(Ventless)
Complete
1Spray down the inside of the machine and scrub
any hard-to-reach spots with a clean, damp cloth.
2Remove rack track, strainer, scrap basket and
ASR basket* to clean and rinse.
3Make sure the upper and lower wash and
rinse arms rotate freely and are clear of
any obstructions.
4Re-assemble the machine.
a. Replace strainer and scrap basket,
b. Install wash and rinse arms (if removed)
c. Replace rack track
d. Replace ASR basket if necessary
5Close the door. Hold the POWER button for
5 seconds to shut down. Power button will
turn half green and lights will turn off when
machine is fully drained.
6After machine is drained, open hood and clean
inside of the machine with a damp cloth.
7If there is water remaining in the tank, drain
remaining water by holding down the DRAIN
button for 3 seconds while the machine is off.
8After cleaning, wipe down
machine exterior with a damp
cloth. Open machine door.
SCAN TO
WATCH DAILY
CLEANING VIDEO
Blue Bold Text = Clean Daily
SCAN TO WATCH
INSTRUCTIONAL
VIDEO
hobartcorp.com/am16training
REPLACING CHEMICALS
1. When the machine is out of
SANITIZER or DETERGENT
an alarm will sound & the
machine will automatically
pause operation. SANITIZER
EMPTY or DETERGENT EMPTY
and an ICON display on the machine control screen.
2. Replace the sanitizer or detergent. NOTE: Use only
commercial detergents & sanitizers with the AM16.
3. Chemical pumps will prime automatically once the
ENTER button is pressed.
Wash/Rinse arm
Scrap
basket
Strainer
Rack track
Wash tank
Wash/Rinse arm
Stand
pipe
ASR basket
*Scrap baskets
Base ASR/ADV
/