WAC Lighting R6ESDR Operating instructions

Type
Operating instructions

This manual is also suitable for

LOTOS
SAFETY INSTRUCTION
c
c
AVERTISSEMENT
CAUTION
OVERALL DIMENSIONS
29/32"
Ø5 1/16"
4 1/4"
4 1/4"
14 1/4"
29/32"
Ø4 1/16"
Ø6 1/16"
14 1/4"
1 3/8"
1 3/8"
Ø7 3/16"
Ø3 1/8"
Ø5 3/32"
SPECIFICATIONS
Input: -277
Installation:
Dimming:
6 1/16"7 3/16"
29/32"
29/32"
4 1/16"5 1/16"
2 3/8"
1 3/8"
4 1/4"
1 3/8"
14 1/4"
14 1/4"
4 1/4"
2 3/8"
3 3/4"
3 3/4"
R4ERDR, R6ERDR, R4ESDR, R6ESDR
R4ERDR
R6ERDR
R4ESDR
R6ESDR
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters, East Manufacturing Facility
44 Harbor Park Drive
Port Washington, NY 11050
South East Manufacturing Facility
1600 Distribution Ct
Lithia Springs, GA 30122
Central Manufacturing Facility
1700 South J Elmer Freeway, Ste 100
Cedar Hill, TX 75104
West Manufacturing Facility
1750 S Archibald Ave
Ontario, CA 91761
2
INSTALLATION INSTRUCTION
R4ERDR, R6ERDR, R4ESDR, R6ESDR
INSTALLATION
1. At the point of installation, cut a round hole for the trim (See FIG.2 ).
For R4ERDR & R4ESDR cut the hole Ø4 1/4" diameter
For R6ERDR & R6ESDR cut the hole Ø6 1/4" diameter
2. Ceiling thickness range is ½” to 1 ”.
3. xture from packaging box.
5. Pull building supply wires through the xture junction box door. (See FIG.3 )
Remove desired housing knockout and feed building wires into housing using appropriate connector.
6. xture wires to building wires (See FIG. 4):
Connect each supply wire with appropriate junction box wire connector. xture features electronic low voltage (ELV) or TRIAC
dimming capabilities.
To utilize ELV or ations.
x x xture wire to ground. Leave all
other wires capped individually.
7. Place all wiring and connectors back in driver box and replace the box’s cover.
9. Fold torsion secure
(See FIG.6 ).
FIG. 2 FIG. 3
FIG.5
FIG. 4
FIG.6
ROUND: CUT OUT
R4ERDR & R4ESDR : Ø4 1/4"
R6ERDR & R6ESDR : Ø6 1/4"
8. Insert driver box through the mounting hole and secure to ceiling joist. (See FIG. 5).
Black − Hot
Green Ground
White Neutral
Power supply
Cable to fixture
4. Adjust to desired color temperature using switch on the side of the driver (See FIG. 1).
FIG. 1
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters, East Manufacturing Facility
44 Harbor Park Drive
Port Washington, NY 11050
South East Manufacturing Facility
1600 Distribution Ct
Lithia Springs, GA 30122
Central Manufacturing Facility
1700 South J Elmer Freeway, Ste 100
Cedar Hill, TX 75104
West Manufacturing Facility
1750 S Archibald Ave
Ontario, CA 91761
  • Page 1 1
  • Page 2 2

WAC Lighting R6ESDR Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI