Modern Forms PD-43728 Metric Operating instructions

Category
Wall & ceiling mounts accessories
Type
Operating instructions
1
INSTALLATION INSTRUCTIONS
437 – LED Pendant
PD-43728
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
Read all instructions before installing.
System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
Lisez toutes les instructions avant l’installation.
Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty:1 Extra
AB
2
INSTALLATION INSTRUCTIONS
437 – LED Pendant
PD-43728
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and
remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back
plate from the xture.
4. Secure the mounting back plate to the
junction box using standard junction box
screws that comes with the junction box.
Note: the side of the mounting plate
marked “GND” must face out.
5. Adjust the xture wire length by pushing
the cable gripper on the canopy and pulling
the wire as desired.
a. Retract these wires close to a desirable
length to within the canopy before securing
the xture in place. Using the cable gripper to
adjust more than 18” of wire length is not desirable.
b. Warning: Shortening these cables without
professional helps or electronic background is not
advisable. Any modications to the xture will
result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
6. Connect the drivers input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xtures ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
7. Secure the xture to the mounting back plate using the mounting screw (B) .
DIMMING WIRING INFORMATION (Fig. 3)
8. This xture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specic dimming wires
information.
9. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
10. To utilize 0-10V dimming: use wire purple (dim+), pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
Mounting Screw
Junction Box Screw
Junction Box
Black Wire
White Wire
Wire Connector
A
B
Driver(Canopy Inside)
3 3/8"L x 2 3/8"W x 1 1/8"H
Cable-gripper
Instruction:Adjust the
fixture wire length by
pushing the cable gripper
on the canopy and pulling
the wire as desired.
Push up
Bare Copper Ground Wire
Back Plate Dimensions
Ø
53
8"
13
4"
13
8"
Fig.3 Driver Wiring
Purple - Dim+
Pink or Gray -Dim-
Black - Hot
White - Neutral
Black - Output -
Red - Output +
1
INSTALLATION INSTRUCTIONS
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Apr. 2020
CAUTION: To prevent electrical shock, ensure electricity has b at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
W xture, do not apply pressure to the LEDs. xture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and r xture. We recommend that customers in coastal
areas clean all external surfac xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chi on humide.
Wire Connector
Qty: 3pcs+1Extra
Mounting Screw
Qty:1 Extra
A B C D
Plastic Anchor
Qty: 3pcs+1 Extra
Qty: 3pcs+1 Extra
Wood Screw
437 – LED Pendant
PD-43738/PD-43748
PREPARATION
ow a ov
B t y
a
MOUNTING THE FIXTURE (Fig. 1)
3. R ov at
4. D w
at at
D
5. S at t ox
o w at
o t t w w
C
Note -o tu o
o ay t
T at “GND” t.
.
R a t t y
Note a xt x v
.
Warning Sho t o t
v wa a t t.
7. P o t . T t
tu o t y.
CONNECTING THE WIRES (Fig. 3)
8. C v t o o F . 3,
a t A . I y o
o . A t t
ox.
9. P ty o t at to
w
11. A t F .1.
COMPLETING THE INSTALLATION
DIMMING WIRING INFORMATION (Fig. 4)
14. T z L TR t
15. T z a
t
2
INSTALLATION INSTRUCTIONS
437 – LED Pendant
PD-43738/PD-43748
FIG. 1
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Apr. 2020
modernforms.com
P
F
Headquarters/Eastern Distribution Center
44 Ha Pa v
Po t W t N
Central Distribution Center Western Distribution Center
A Av
O ta o, C
Fixture Wires
Fixture Wires
Wt
R
Fixture Wires
Ba
G
House Wires
House Wires
Wt
House Wires
GC
G
FIG. 3 Wiring
FIG. 2
FIG. 4
Purple - Dim +
Pink or Gray - Dim -
Black - Hot
White - Neutral
Black - Output -
Red - Output +
Mou S w
Ju ox S w
Ju ox
B a
W
Wh
W
W o o
W S w
a tt ho
D C y I
3 3/8"L x 2 3/8"W x 1 1/8"H
Ca
I t u t o A t th
xtu th y
u th
o th a o y a
th a .
Pu h u
Ba o
Go W
Sa ty Co
O y PD-43748
La Bo y
Back Plate Dimensions
Ø
87
8
"
13
4
"
13
8
"
31
8
"
13
4
"
Ou
ut
2
Wh t -
ut a
-
Hot
tu
ut
1
Ou
I
Ou
I
No t ty
pink or
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Modern Forms PD-43728 Metric Operating instructions

Category
Wall & ceiling mounts accessories
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages