Toro Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers Installation guide

Brand: Toro

Model: Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers

Type: Installation guide

Toro Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers is designed to be used with Z400 Z Masters with 52 inch mower decks and Z500 Z Master Estate Models. It helps prevent scalping, which can occur when the mower deck is too low to the ground and the blades hit the ground. The kit includes an anti-scalp roller, mounting brackets, and hardware. The anti-scalp roller is made of a durable material that can withstand the rigors of mowing. The mounting brackets are designed to fit securely to the mower deck, and the hardware is corrosion-resistant to ensure a long service life.

Form No. 3356-133 Rev A

Discharge Side Rear Anti-Scalp Roller Kit

For Z Master Mowers

Model No. 112–1792

Installation Instructions

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

T his kit is for Z400 Z Masters with 52 inc h mo w er

dec ks and Z500 Z Master Estate Models .

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the mower.

Inside mounting plate

Outside mounting plate

Carriage bolt (3/8 x 3/4 inch)

Nut (3/8 inch)

Bolt (3/8 x 4–1/2 inches)

Anti-scalp roller

Bushing

Spacer

Install the new mounting plate.

Step

Preparing the Mower

No Parts Required

Procedure

1. T horoughly clean mo w er dec k. All debris m ust

be remo v ed to ensure the mounting brac k et

will ﬁt properly ag ainst mo w er dec k.

2. R e pair all bent or damag ed areas of mo w er

dec k and re place any missing par ts .

Step

Installing the Anti-scalp

Roller and Brackets

Parts needed for this step:

Inside mounting plate

Outside mounting plate

Carriage bolt (3/8 x 3/4 inch)

Nut (3/8 inch)

Bolt (3/8 x 4–1/2 inches)

Anti-scalp roller

Bushing

Spacer

Procedure

1. Loosely install the inside brac k et to the mo w er

dec k with 2 car riag e bolts (3/8 x 3/4 inc h) and

2 n uts (3/8 inc h) as sho wn in Figure 1 .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Do not tighten these bolts . T hese will be

tightened after all par ts are loosely installed.

2. Loosely install the outside brac k et to the

mo w er dec k with 2 car riag e bolts (3/8 x 3/4

inc h) and 2 n uts (3/8 inc h) as sho wn in Figure

1 .

Do not tighten these bolts . T hese will be

tightened after all par ts are loosely installed.

3. Install the anti-scalp roller , spacer , and bushing

betw een the tw o mounting brac k ets with a bolt

(3/8 x 4–1/2 inc hes) and n ut (3/8 inc h)( Figure

1 ).

Figure 1

1. Carriage bolt (3/8 x 3/4

inch)

5. Anti-scalp roller

2. Outside bracket 6. Bushing

3. Nut (3/8 inch)

7. Spacer

4. Bolt (3/8 x 4–1/2 inches)

8. Inside bracket

4. Tighten the bolts holding the mounting

brac k ets to the mo w er dec k ( Figure 1 ).

5. Tighten the bolt for the anti-scalp roller .

Toro Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers Installation guide

Toro Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers Installation guide

Toro Discharge Side Rear Anti-Scalp Roller Kit, Z Master Mowers Installation guide

Related papers

Other documents