Perlick CR24D-1-4L Installation guide

Brand: Perlick

Model: CR24D-1-4L

Type: Installation guide

FORM NO. Z2496

REV. A-11/29/2017

PERLICK COLLECTION 24” COLUMN REFRIGERATION

To prevent appliance damage and injury, read these instrucons thoroughly

prior to installaon.

CR24

INSTALLATION

INSTRUCTIONS

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

2 | perlick.com/residential

PRODUCT IDENTIFICATION PLATE

Your product informaon can be found on the product’s

idencaon plate. The idencaon plate for CR24 column

refrigeraon models is located on the sidewall behind the toe

kick plate. To access the indencaon plate, simply remove

the toe kick plate (grill). The idencaon plate will be adhered

to the right sidewall.

INTRODUCTION

Congratulaons on your purchase of a Perlick Collecon column

refrigeraon appliance. This manual has been prepared to assist

you in the installaon of your column refrigerator, freezer and

wine reserve.

We dedicate considerable me to ensure that our products

provide the highest level of customer sasfacon. We thank

you for selecng Perlick products for your home and assure you

of our connuing interest in your sasfacon.

WARRANTY REGISTRATION

To register your Perlick product, visit our website at

www.perlick.com/RegisterMyPerlick and ll out the form.

Once completed, click on the ‘Submit Warranty Registraon’. Be

sure to register your product immediately upon installaon to

receive the warranty from installaon date instead of shipment

date. If le blank, the date will revert back to shipment date.

CONTENTS

3 Safety Consideraons

4 Prior to Installaon

4 Opening Dimensions (Single and Dual)

5 Niche/Product Dimensions

6 Electrical

6 An-p Bracket

7 Leveling/Alignment

10 Door/Side Panel Informaon

16 Door Panel Installaon/Adjustment

18 Door Trim Installaon

19 Compleon - Grill Installaon

20 Toe Kick Clearance

21 Installing Filters

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 3

SAFETY CONSIDERATIONS

IMPORTANT SAFETY INFORMATION

Please review the following safety precauons and read all

instrucons prior to product installaon. Aer the compleon

of installaon, keep these instrucons in a safe place for future

reference.

Please take special care when reading the highlighted

informaon in this guide. This informaon is coded as follows:

DAN Thisindicatesthatahazardoussituaon

mayoccurwheninstruconsarenotfollowed.Itisimperive

thatdireconsinthisguidearefollowedtopreventpossible

serious injury or death.

  Thisindicatesasituaonwhereminor

injury,productorcabinetdamagemayoccurifthefollowing

instruconsarenotfollowed.

This highlights informaon that is of

signicant importance.

WARNING

DANGER

CAUTION

SAFETY PRECAUTIONS

Please take note of the following safety precauons prior to

moving, unpacking and installing your Perlick column.

DAN Takecarewhenhandling,movingorusing

therefrigeratedcabinettoavoiddamagingtherefrigerant

tubing.Damagingtherefrigeranttubingincreasestheriskof

leakageandcanbedangerous.

  Perlickcolumnsweighupto550lbs.Take

specialcarewhenmovingtopreventseriousinjury.

  Perlickcolumnsaretopheavy.Itis

importantthatthedoorissecuredclosedunlinstalled.

Installasdirectedtopreventpping.

  Donotuseorstoreammableliquids(ie;

gasoline)orvaporsnearappliances.

  Inspecttheelectricalcordandplugfor

damage prior to plugging the unit in.

  Intheeventthatserviceisneccessary,

repairworkmustbeperformedbyaPerlickauthorized

servicerastominimizetheriskofpossibleigniondue

toincorrectpartsorimproperservice.Workdoneby

unqualiedindividualscouldpotenallybedangerousand

willvoidthewarranty.Componentpartswillbereplaced

withlikecomponentsfromPerlick.

DANGER

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

4 | perlick.com/residential

PRIOR TO INSTALLATION

Before beginning installaon, carefully

inspect the cabinet for hidden damage. If damage is discovered,

immediately le a claim with the transportaon company.

Perlick is not responsible for damage in transit.

When moving the unit, be sure to protect

nished ooring with appropriate material to avoid damage

from moving the appliance.

If the unit has been laid on its back or sides,

place unit upright and allow minimum of 24 hours before

connecng the unit. Failure to do so can aect the funcon and

performance of the appliance.

This appliance should be installed in dry,

venlated indoor locaon. The ambient temperature of the

locaon must be between 55°F (13°C) and 100°F (43°C) for

opmal performance.

This product must be installed on a level

oor for safety and opmal performance. The base must be

at to ensure an-p brackets properly funcon and that

the refrigeraon system is level. Any walls and surrounding

furniture/xtures need to be securely aached to the oor, wall

studs or concrete prior to installaon of the column.

To ensure proper performance, the air

intake (toe kick) must not be blocked. Perlick refrigeraon is

front-breathing — covering the intake will cause the system to

overheat and fail.

In addion, the appliance must not be in direct exposure of

constant sunlight or excessive heat. If it must be installed next

to a heat source, such as a cooking appliance or radiant heat,

you must install an insulang plate between the column and

heat source.

When fully stocked, Perlick column refrigeraon is very heavy.

To ensure the safety and prevent home damage, the load-

bearing capacity of your oor must be 846 lbs (384 kg).

CAUTION

INSTALLATION TOOLS AND MATERIALS

▪ Screwdrivers (standard and #2 Phillips)

▪ Power drill

▪ Drill bits

▪ 13mm socket or wrench set

▪ 2’ and 4’ levels

▪ Material to protect ooring and surrounding cabinetry

OPENING DIMENSIONS - SINGLE UNIT

The depth of each Perlick column is 24” (610). Allow for

panel thickness when planning the nished opening depth. A

minimum of a 4” (102) nished return is required on all sides

of the opening. See page 5 for niche and product dimension

drawings.

It is important that the side walls of the niche are plumb prior

to installaon. The minimum thickness of both the side walls

and the top wall must be 5/8” (16). A thickness of 3/4” (19) is

recommended for toe kick panels.

Framed cabinets will require addional nished ller material

behind the face frame for a proper installaon. Refer to the

illustraon on page 5.

OPENING DIMENSIONS - TWO UNITS

When installing two units side-by-side, a Perlick Dual

Installaon Kit (part number CR-ACC-D1) is required. You must

plan for both units plus dual installaon kit when planning the

cut-out dimensions. For more informaon, see instrucons that

accompany the CR-ACC-D1.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 5

NICHE / PRODUCT DIMENSIONS

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

6 | perlick.com/residential

ELECTRICAL

Serious electroculon hazard. Electrical

grounding is required. This appliance is equipped with a

3-prong (grounding) polarizing plug for your protecon against

possible shock hazards. Failure to comply with these electrical

guidelines may result in possible death or serious injury, re or

loss of property.

Never use an extension cord to connect unit

to electrical source. Do not use a two-prong adapter or remove

the power cord grounding prong.

Installaon must comply with all applicable electrical codes.

The electrical supply must be located within the shaded area

of the illustraon below. A separate circuit, servicing only this

appliance, is required. A ground fault circuit interrupter (GFCI)

is not recommended and may cause interrupon of operaon.

The outlet should be placed in the hatched area dimensioned

below.

Electrical Supply 115V, 60 Hz., Phase 2, 3.3 amps

Service Dedicated 15 amp circuit

Power/Cord Type/ Length NEMA 5-15P w/5’ power cord

WARNING

DANGER

ANTI-TIP BRACKET

To prevent the unit from pping forward,

the an-p bracket must be installed. Use all an-p bracket

hardware as instructed. Level as instructed on page 7 prior to

installing an-p bracket(s)

The an-p bracket and supporng hardware is included with

your unit. Please note that four an-p brackets are required

for each unit or dual installaon. In the case of dual installaon,

each individual unit must be ouied with the two an-p

brackets on cabinet sides for a total of four.

For drawings of the an-p bracket installaon on integrated

(built-in) units, see page 8. For drawings of the an-p bracket

installaon on freestanding units, see page 9.

Verify there are no electrical wires or

plumbing in the area which the screws could penetrate.

Always wear safety glasses and use other

necessary protecve devices or apparel when installing or

working with anchors. Anchors are not recommended for use in

lightweight masonry material such as block or brick, or for use

in new concrete which has not had sucient me to cure. The

use of core drills is not recommended to drill holes for anchors.

WARNING

CAUTION

ELECTRICAL / ANTI-TIP BRACKET / PRODUCT PLACEMENT

PLACEMENT

Before moving unit into posion, secure the

door closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

CAUTION

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 7

LEVELING / ALIGNMENT

LEVELING/ALIGNMENT

Move the unit near the opening. Plug the power cord into the

grounded outlet and roll the unit into posion. Push unit into

place.

Front and rear leveling legs can be adjusted from the front once

the unit is posioned. To access leveling adjustment access

holes, remove toe kick grill.

Once the unit is in posion, height adjustment can be made

from the front. Using the hex driver leveling tool, turn clockwise

to raise the unit or counterclockwise to lower. Refer to the

illustraon below.

WARNING

CAUTION

When the unit is properly leveled, door adjustments are less

likely to be needed.

To reduce the possibility of the unit pping

forward, the front leveling legs must be in contact with the

oor.

The refrigerated cabinet should be level for

proper operaon, such as door closing, drawer and shelf slide

operaon.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

8 | perlick.com/residential

ANTI-TIP BRACKET INSTALLATION FOR INTEGRATED INSTALLATION

NOTE: Do not fasten an-p brackets to

adjacent cabinetry unl the cabinet has been

leveled.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 9

ANTI-TIP BRACKET INSTALLATION FOR FREESTANDING INSTALLATION

NOTE: Cabinet must be leveled before securing

to wall with an-p bracket.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

10 | perlick.com/residential

DOOR / SIDE PANEL INFORMATION

Finish sides of surrounding cabinetry — they will be visible

when the door is open. The height of the custom door panel

can extend beyond the typical panel height provided the door

and overlay combined do not exceed 242 lbs (110) .

See page 15 for screw zone for overlay panels. Hatch areas

should provide enough thickness for wood screw and overlay

aachment brackets.

SIDE PANELS

Units that are freestanding or parally built-in need to be

nished with custom panels. Custom panels can be built to

customer specicaons to match surrounding cabinetry.

DOOR PANELS

Perlick column refrigeraon comes ready to accept a customer

supplied overlay door panel and customer supplied handle.

Stainless steel door panels and Perlick handles are also

available, and are sold separately of the unit itself. Stainless

steel panels and handles can be purchased through an

authorized Perlick dealer.

STAINLESS STEEL DOOR PANELS

Stainless steel door panels for solid and glass door models

are available through an authorized Perlick dealer. Panels are

constructed of 304 stainless steel (front) and 403 (back plate)

and have a thickness of 3/4” (19). Always allow for panel

thickness when planning the nished opening depth.

Stainless steel panels come pre-drilled for a Perlick handle.

Please note that the Perlick Pro Handle is included with the

purchase of a stainless steel panel.

CUSTOM OVERLAY DOOR PANEL

Perlick columns come ready to accept customer-supplied door

panel and handle hardware. The thickness of the custom panel

can vary. A minimum 5/8” (16) thick panel is required, but

the thickness can be increased provided it does not exceed

the maximum panel weight is 65 lbs (29). Please note that

the combined door and overlay weight cannot exceed 242 lbs

(110). The depth of each model is 24” (610) without a nished

overlay. Allow for panel thickness when planning the nished

opening depth. Templates for 4” and 6” solid and glass door

models can be found on pages 11-14.

Reveals between panels can vary – 1/8” (3) is the minimum.

When installing a panel thicker than 3/4”

(19), the 90° stop may be required to prevent damage to the

unit and adjacent cabinetry.

As reveals between cabinetry and the unit

decrease, severe nger pinching can occur while the door is

closing.

CAUTION

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 11

SOLID DOOR TEMPLATE FOR 4” TOE KICK

(4X)

.136 .500

(2X)

.136

.250

1/2" (6X)

DETAIL A

SCALE 1 : 2

OVERLAY MTG CLIP DETAIL

REV.

DESCRIPTION

DATE

APPROVED

REVISIONS

REVISED CLIP HOLE LOCATIONS AND COND.

AIRFLOW MTG HOLE LOCATIONS

11/8/2017

JMP

ADDED CONDENSER DIVIDER HOLES

10/3/2017

JMP

RELEASE FOR PRODUCTION

8/25/2017

JMP

C:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1007916.slddrw

04/11/2017

11/08/2017

JMP

DIMENSIONS ARE IN INCHES TOLERANCES:

Ang = ±1.0°

Frac. = ±1/16

THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY

FORM, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK

DRAWN BY:

APPVD BY:

FINISH:

QTY.:

HOLES:

.0135 THRU

.125:

.004

.1260 THRU

.250:

.005

.2510 THRU

.500:

.006

.5010 THRU

.750:

.008

.7510 THRU

1.000:

.010

1.001 & UP:

.012

BREAK SHARP EDGES - .015 X 45°

RADIUS SHARP FILLETS - .015 TO .031

UNLESS OTHERWISE SPECIFIED:

MATERIAL:

DATE

SIGNATURES

Milwaukee, Wisconsin

Perlick Corporation

DWG NO.

REFERENCE:

PART NO.

PURCHASE REC.:

TITLE:

1007916

1007916-1

COLUMN REFRIGERATOR / FREEZER

DOOR WOOD FASCIA - 4" TOE KICK

SCALE = 1:10

SHEET 1 OF 2

WOOD

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

12 | perlick.com/residential

SOLID DOOR TEMPLATE FOR 6” TOE KICK

(4X)

.136 .500

(12X)

.188

.250

(2X)

.136

.250

1/2" (6X)

DETAIL B

SCALE 1 : 2

OVERLAY MTG CLIP DETAIL

REV.

DESCRIPTION

DATE

APPROVED

REVISIONS

REVISED CLIP HOLE LOCATIONS AND COND.

AIRFLOW MTG HOLE LOCATIONS

11/8/2017

JMP

ADDED CONDENSER DIVIDER HOLES

10/3/2017

JMP

RELEASE FOR PRODUCTION

8/25/2017

JMP

C:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1007916.slddrw

04/11/2017

11/08/2017

JMP

DIMENSIONS ARE IN INCHES TOLERANCES:

Ang = ±1.0°

Frac. = ±1/16

THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY

FORM, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK

DRAWN BY:

APPVD BY:

FINISH:

QTY.:

HOLES:

.0135 THRU

.125:

.004

.1260 THRU

.250:

.005

.2510 THRU

.500:

.006

.5010 THRU

.750:

.008

.7510 THRU

1.000:

.010

1.001 & UP:

.012

BREAK SHARP EDGES - .015 X 45°

RADIUS SHARP FILLETS - .015 TO .031

UNLESS OTHERWISE SPECIFIED:

MATERIAL:

DATE

SIGNATURES

Milwaukee, Wisconsin

Perlick Corporation

DWG NO.

REFERENCE:

PART NO.

PURCHASE REC.:

TITLE:

1007916

1007916-2

COLUMN REFRIGERATOR / FREEZER

DOOR WOOD FASCIA - 6" TOE KICK

SCALE = 1:10

SHEET 2 OF 2

WOOD

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 13

GLASS DOOR TEMPLATE FOR 4” TOE KICK

60"

CUTOUT

17" CUTOUT

" TYP

FOR LOCK OPTIONAL

USE DRILL FIXTURE TO

LOCATE HOLE

.136

.500 (4X)

.136

.500 (2X)

1/2" (6X)

DETAIL A

SCALE 1 : 2

OVERLAY CLIP MTG HOLES

REV.

DESCRIPTION

DATE

APPROVED

REVISIONS

REVISED MTG HOLE LOCATIONS AND COND. AIRFLOW

DIVIDER MTG HOLES

11/8/2017

JMP

UPDATED CLIP MTG HOLE LOCATIONS

10/6/2017

JMP

REVISED WINDOW SIZE BY INCREASE CUTOUT WIDTH AND

HEIGHT BY 1-1/4" OVERALL

10/5/2017

JMP

ADDED HOLES FOR CONDENSER AIR DIVIDER

10/3/2017

JMP

UPDATED HOLE PATTERN FOR ADJUSTMENT BRKT

8/25/2017

JMP

INITIAL RELEASE

11/8/2016

TEC

C:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1007917.slddrw

11/28/2016

11/08/2017

JMP

DIMENSIONS ARE IN INCHES TOLERANCES:

THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY

FORM, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK

DRAWN BY:

APPROVED BY:

FINISH:

QTY.:

HOLES:

.0135 THRU

.125:

.004

.1260 THRU

.250:

.005

.2510 THRU

.500:

.006

.5010 THRU

.750:

.008

.7510 THRU

1.000:

.010

1.001 & UP:

.012

BREAK SHARP EDGES - .015 X 45°

RADIUS SHARP FILLETS - .015 TO .031

UNLESS OTHERWISE SPECIFIED:

MATERIAL:

DATE

SIGNATURES

Milwaukee, Wisconsin

Perlick Corporation

DWG NO.

REFERENCE:

PART NO.

PURCHASE REC.:

TITLE:

1007917

FOR COLUMN WINE

OVERLAY, WOOD, 4'' TOE KICK

SCALE = 1:10

SHEET 1 OF 4

WOOD

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

14 | perlick.com/residential

GLASS DOOR TEMPLATE FOR 6” TOE KICK

60"

CUTOUT

17" CUTOUT

" TYP

FOR LOCK OPTIONAL

USE DRILL FIXTURE TO

LOCATE HOLE

.136

.500 (12X)

.136

.500 (4X)

.136

.500 (2X)

1/2" (6X)

DETAIL

SCALE

1 : 2

OVERLAY CLIP MTG HOLES

REV.

DESCRIPTION

DATE

APPROVED

REVISIONS

REVISED MTG HOLE LOCATIONS AND COND. AIRFLOW

DIVIDER MTG HOLES

11/8/2017

JMP

UPDATED CLIP MTG HOLE LOCATIONS

10/6/2017

JMP

REVISED WINDOW SIZE BY INCREASE CUTOUT WIDTH AND

HEIGHT BY 1-1/4" OVERALL

10/5/2017

JMP

ADDED HOLES FOR CONDENSER AIR DIVIDER

10/3/2017

JMP

UPDATED HOLE PATTERN FOR ADJUSTMENT BRKT

8/25/2017

JMP

INITIAL RELEASE

11/8/2016

TEC

C:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1007917.slddrw

11/28/2016

11/08/2017

JMP

DIMENSIONS ARE IN INCHES TOLERANCES:

Ang = ±1.0°

Frac. = ±1/16

THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY

FORM, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK

DRAWN BY:

APPROVED BY:

FINISH:

QTY.:

HOLES:

.0135 THRU

.125:

.004

.1260 THRU

.250:

.005

.2510 THRU

.500:

.006

.5010 THRU

.750:

.008

.7510 THRU

1.000:

.010

1.001 & UP:

.012

BREAK SHARP EDGES - .015 X 45°

RADIUS SHARP FILLETS - .015 TO .031

UNLESS OTHERWISE SPECIFIED:

MATERIAL:

DATE

SIGNATURES

Milwaukee, Wisconsin

Perlick Corporation

DWG NO.

REFERENCE:

PART NO.

PURCHASE REC.:

TITLE:

1007917

FOR COLUMN WINE

OVERLAY, WOOD, 6'' TOE KICK

SCALE = 1:10

SHEET 2 OF 4

WOOD

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 15

SCREW ZONE FOR OVERLAY TEMPLATES

66"

NOTE:

HATCH AREAS SHOULD PROVIDE ENOUGH

THICKNESS FOR WOOD SCREW FOR

OVERLAY ATTACHMENT BRACKETS.

REV.

DESCRIPTION

DATE

APPROVED

REVISIONS

REVISED MTG HOLE LOCATIONS AND COND. AIRFLOW

DIVIDER MTG HOLES

11/8/2017

JMP

UPDATED CLIP MTG HOLE LOCATIONS

10/6/2017

JMP

REVISED WINDOW SIZE BY INCREASE CUTOUT WIDTH AND

HEIGHT BY 1-1/4" OVERALL

10/5/2017

JMP

ADDED HOLES FOR CONDENSER AIR DIVIDER

10/3/2017

JMP

UPDATED HOLE PATTERN FOR ADJUSTMENT BRKT

8/25/2017

JMP

INITIAL RELEASE

11/8/2016

TEC

C:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1007917.slddrw

11/28/2016

11/08/2017

JMP

DIMENSIONS ARE IN INCHES TOLERANCES:

THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY

FORM, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK

DRAWN BY:

APPROVED BY:

FINISH:

QTY.:

HOLES:

.0135 THRU

.125:

.004

.1260 THRU

.250:

.005

.2510 THRU

.500:

.006

.5010 THRU

.750:

.008

.7510 THRU

1.000:

.010

1.001 & UP:

.012

BREAK SHARP EDGES - .015 X 45°

RADIUS SHARP FILLETS - .015 TO .031

UNLESS OTHERWISE SPECIFIED:

MATERIAL:

DATE

SIGNATURES

Milwaukee, Wisconsin

Perlick Corporation

DWG NO.

REFERENCE:

PART NO.

PURCHASE REC.:

TITLE:

1007917

FOR COLUMN WINE

OVERLAY, WOOD, 4'' TOE KICK

SCALE = 1:10

SHEET 3 OF 4

WOOD

NOTE:HATCHAREASSHOULD

PROVIDEENOUGHTHICKNESS

FORWOODSCREWSFOROVERLAY

ATTACHMENTBRACKET.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

16 | perlick.com/residential

DOOR PANEL INSTALLATION

Typical panel dimensions are based on 84” (2134) nished

height with 1/8” (3) reveals. Template must be adjusted for

panels exceeding typical dimensions.

Place panel face down on a protected work surface. Aach

six clips to the back of overlay in locaons indicated in wood

overlay drawing below.

Use provided #10 x 1/2” screws to aach clips to overlay.

Overlay then slides onto door face. Aach overlay to door

adjustment brackets using remaining #10 x 1/2” screws. Once

mounted, adjust overlay to match adjacent cabinetry.

INSTALLING DOOR OVERLAY PANELS

DOOR OVERLAY PANEL ADJUSTMENT

Close the door to make adjustments to align panels and reveals.

For up and down adjustments, turn the height adjustment

screws in the top bracket (see Top of Door illustraon on page

17) in and out. Adjust the screws as needed to achieve an even

reveal on each side of the door overlay.

Once nal adjustments are made to the posion of the door

overlay, secure the overlay in place by installing the boom

overlay brackets as shown in Boom of Door illustraon below.

BOTTOM OF DOOR

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 17

TOP OF DOOR ILLUSTRATION

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

18 | perlick.com/residential

DOOR TRIM INSTALLATION

Once overlay is adjusted, mount the door trim bracket onto the

door adjustment bracket using the provided screws.

DOOR TRIM INSTALLATION

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

perlick customer service (800)558-5592 | 19

COMPLETION - GRILL INSTALLATION

GRILL INSTALLATION

Install the grill by snapping into latch catches.

PERLICK RESIDENTIAL COLUMN REFRIGERATION INSTALLATION INSTRUCTIONS

20 | perlick.com/residential

TOE KICK CLEARANCE

Page is loading ...

Perlick CR24D-1-4L Installation guide

Perlick CR24D-1-4L Installation guide

Perlick CR24D-1-4L Installation guide

Related papers

Other documents