Beckhoff Economy CP213-0001 Installation And Operating Instructions Manual

Brand
Beckhoff
Model
Economy CP213-0001
Category
Uninterruptible power supplies (UPSs)
Type
Installation And Operating Instructions Manual
Installation and Operating instructions for
“Economy” Panel PC CP72xx
Version: 2.1
Date: 2019-10-09
Table of contents
CP72xx 1
Table of contents
1. Foreword 3
Notes on the Documentation 3
Liability Conditions 3
Trademarks 3
Patent Pending 3
Copyright 3
State at Delivery 3
Delivery conditions 3
Description of safety symbols 4
Basic safety measures 5
Operator’s obligation to exercise diligence 6
Operator requirements 6
2. Product Description 7
Appropriate Use 7
Structure 7
Access to memory and battery 8
Interfaces 10
Power supply 10
Network connection 10
Additional plug-in cards (optional) 10
3. Installation Instructions 11
Transport and Unpacking 11
Transport 11
Unpacking 11
Installation of the Panel PC 12
Mounting arm installation 12
Earthing measures 13
Power Supply Connection 14
Beckhoff power supply technology 14
Pin assignment of the power supply connector 15
Pre-assembled cable sets for the power supply 16
Fitting the power supply cable with IP65 connector 16
Connecting Power Supply 17
Cable Cross Sections 17
Configuration for shutting down the PC 17
PC_ON and Power Status functions 17
Wiring diagram CP72xx 18
Wiring diagram CP72x4 with 24-inch display (discontinued) 19
Connecting the Network 20
Pre-assembled network cables 20
Fitting the network cable with IP65 connector 20
USB-interface (optional) 21
Pre-assembled USB-cables 21
Fitting the USB-cable with IP65 connector 21
RS232-interface (optional) 22
Pre-assembled serial interface cables 22
Fitting the RS232-interface cable with IP65 connector 22
Connecting devices 23
Connecting cables 23
Check voltage rating and connect 23
4. Operating Instructions 24
Switching the Industrial PC on and off 24
First switching on and driver installation 24
Keyboard codes 25
Maintenance 27
Cleaning the Industrial PC 27
Servicing 27
Replacing the battery on the motherboard 27
Table of contents
2 CP72xx
Emergency procedures 27
Shutting down 27
Disposal 27
5. UPS Software Components (optional) 28
Installation on the PC 28
Help files 28
6. Troubleshooting 29
Fault correction 29
Beckhoff Support & Service 30
Beckhoff branches and partner companies 30
Beckhoff Headquarters 30
Beckhoff Support 30
Beckhoff Service 30
7. Appendix 31
Assembly dimensions 31
Dimensions and total weight 35
8. Appendix 36
Technical data 36
Approvals 36
FCC: Federal Communications Commission Radio Frequency Interference
Statement 36
FCC: Canadian Notice 36
Foreword
CP72xx 3
Foreword
Notes on the Documentation
This description is only intended for the use of trained specialists in control
and automation engineering who are familiar with the applicable national
standards. It is essential that the following notes and explanations are
followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the
products described satisfy all the requirements for safety, including all the
relevant laws, regulations, guidelines and standards.
Liability Conditions
The documentation has been prepared with care. The products described
are, however, constantly under development. For that reason the
documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it
contains technical or editorial errors, we retain the right to make alterations
at any time and without warning. No claims for the modification of products
that have already been supplied may be made on the basis of the data,
diagrams and descriptions in this documentation.
All pictures shown in the documentation are exemplary. Illustrated
configurations can differ from standard.
Trademarks
Beckhoff
®
, TwinCAT
®
, EtherCAT
®
, Safety over EtherCAT
®
, TwinSAFE
®
,
XFC
®
and XTS
®
are registered trademarks of and licensed by Beckhoff
Automation GmbH.
Other designations used in this publication may be trademarks whose use
by third parties for their own purposes could violate the rights of the
owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the
following patent applications and patents: EP1590927, EP1789857,
DE102004044764, DE102007017835 with corresponding applications or
registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the
following patent applications and patents: EP0851348, US6167425 with
corresponding applications or registrations in various other countries.
Copyright
© Beckhoff Automation GmbH & Co. KG.
The reproduction, distribution and utilization of this document as well as the
communication of its contents to others without express authorization are
prohibited. Offenders will be held liable for the payment of damages. All
rights reserved in the event of the grant of a patent, utility model or design.
State at Delivery
All the components are supplied in particular hardware and software
configurations appropriate for the application. Modifications to hardware or
software configurations other than those described in the documentation
are not permitted, and nullify the liability of Beckhoff Automation GmbH &
Co. KG.
Delivery conditions
In addition, the general delivery conditions of the company Beckhoff
Automation GmbH & Co. KG apply.
Foreword
4 CP72xx
Description of safety symbols
The following safety symbols are used in this operating manual. They are
intended to alert the reader to the associated safety instructions.
DANGER
Acute risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is
immediate danger to life and health of individuals!
WARNING
Risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is
danger to life and health of individuals!
CAUTION
Hazard to individuals!
If you do not adhere the safety advise adjoining this symbol, there is
obvious hazard to individuals!
Attention
Hazard to devices and environment
If you do not adhere the notice adjoining this symbol, there is obvious
hazard to materials and environment.
Note
Note or pointer
This symbol indicates information that contributes to better understanding.
Foreword
CP72xx 5
Basic safety measures
Only switch the PC off after
closing the software
Before the Industrial PC is switched off, software that is running must
be properly closed.
Otherwise it is possible that data on the storage medium is lost. Please
read the section Switching the Industrial PC on and off.
Attention
Switch off all parts of the equipment, then uncouple the fieldbus
Before opening the housing of the PC, and whenever the PC is being
used for purposes other than plant control, such as during functional tests
following repair, all parts of the equipment must first be switched off, after
which the Industrial PC can be uncoupled from the plant.
Pulling out the fieldbus connection plug uncouples the PC (optional).
Items of equipment that have been switched off must be secured against
being switched on again.
The Industrial PC’s power supply unit must be supplied with 24V
DC
.
CAUTION
Do not open the power supply unit while voltage is applied!
The supply voltage must be switched off before the power supply unit
housing is opened.
Attention
Do not exchange any parts when under power
When components are being fitted or removed, the supply voltage must
be switched off.
Fitting work on the Industrial PC can result in damage:
• if metal objects such as screws or tools fall onto operating circuit
boards.
• if connecting cables internal to the PC are removed or inserted
during operation.
• if plug-in cards are removed or inserted when the PC is switched
on.
DANGER
High Voltage!
Displays used for the Control Panel’s LC-display are operated with a
voltage of up to 1000 V, depending on type. For that reason:
The supply voltage must be disconnected before the housing of the
Control Panel is opened.
Foreword
6 CP72xx
Operator’s obligation to exercise diligence
The operator must ensure that
• the Industrial PC is only used for its intended purpose (see chapter
Product Description).
• the Industrial PC is only operated in a sound condition and in
working order (see chapter Maintenance).
• the Industrial PC is operated, maintained and repaired only by
suitably qualified and authorized personnel.
• the personnel is instructed regularly about relevant occupational
safety and environmental protection aspects, and is familiar with
the operating manual and in particular the safety notes contained
herein.
• the instruction manual is in good condition and complete, and
always available for reference at the place of installation of the
Industrial PC.
• none of the safety and warning notes attached to the Industrial PC
are removed, and all notes remain legible.
• every user is familiar with all the functions of the software installed
on the Industrial PC to which he has access.
National regulations
depending on the machine
type
Depending on the type of machine and plant in which the Industrial PC is
used, national regulations governing the controllers of such machines will
apply, and must be observed by the operator. These regulations cover,
amongst other things, the intervals between inspections of the controller.
The operator must initiate such inspections in good time.
Note
Only trained persons may open the Industrial PC housing
The operator is responsible for ensuring that only trained electrical staff
opens the housing of the Industrial PC.
Procedure in the event of a
fault
In the event of faults at the Industrial PC, the list in the section
Troubleshooting can be used to determine the measures to be taken.
Operator requirements
Read the operating
instructions
Anyone who uses the Industrial PC must have read these operating
instructions.
Software knowledge
Every user must be familiar with all the functions of the software installed
on the Industrial PC to which he has access.
Product Description
CP72xx 7
Product Description
Appropriate Use
The CP72xx Panel PC with 3½” motherboard is designed for mounting
behind a Beckhoff Control Panel. Cooling is achieved via heat sink
structure between the Control Panel and the add-on PC. A fan inside the
closed housing ensures that the heat is distributed evenly.
The Industrial PC is designed for mounting arm installation.
DANGER
Do not use the Panel PC in areas of explosive hazard!
The Panel PC must not be used where there is a risk of explosion.
Structure
Rear view of theCP72xx
Access to the connectors
In order to get access to the connectors, first unscrew the according M4-
cross-head screws (1) (see photo above). The plastic caps (2) can then be
taken off easily.
View to the connectors
The picture shows the view to the connectors when the plastic caps are
removed.
2
1
1
2
1
1
Product Description
8 CP72xx
Access to memory and battery
Removing the drive cover
After unscrewing the two Allen screws (see arrows) the drive cover can be
taken off.
View to the hard-disk drive
(optional) and the memory
card
Removing the drive cover allows access to the IDE-hard-disk (1) (optional),
the Compact-Flash-memory card (2) and the lithium battery of the system
clock (3).
1
2
3
+ pole
Product Description
CP72xx 9
Removing the hard-disk
drive and the memory card
The hard-disk drive and the memory card can now be pulled out. Here,
changing the lithium battery is also possible.
The installation takes place in reverse order.
WARNING
Danger of Explosion!
Replace battery only with the identical type or an alternative type
recommended by the manufacturer. Notice correct polarity!
WARNING
Handling of Lithium Batteries
Lithium Batteries should not be recharged, exposed to fire, opened and
they should be protected against sunlight and moisture.
polarity
- pole
Product Description
10 CP72xx
Interfaces
Power supply
Power supply
The power supply connection of the Industrial PC and the connection with
the UPS (optional) is established via the power supply socket (X101).
Network connection
Network connection
The Ethernet-interface with RJ-45-connector (X106) allows the PC to be
connected to a network (LAN). In the basic configuration a Gigabit-port is
available.
Additional plug-in cards (optional)
Type plate
There are notes at the Industrial PC and in the connection area which
provide information about the hardware configuration of the Industrial PC at
the time it was supplied.
X101
X106
Installation Instructions
CP72xx 11
Installation Instructions
Please also refer to chapter Foreword.
Transport and Unpacking
The specified storage conditions must be observed (see chapter Technical
data).
Transport
Despite the robust design of the unit, the components are sensitive to
strong vibrations and impacts. During transport, your Control Panel should
therefore be protected from excessive mechanical stress. Therefore,
please use the original packaging.
Attention
Danger of damage to the unit
If the device is transported in cold weather or is exposed to extreme
variations in temperature, make sure that moisture (condensation) does
not form on or inside the device.
Prior to operation, the unit must be allowed to slowly adjust to room
temperature. Should condensation occur, a delay time of approximately
12 hours must be allowed before the unit is switched on.
Unpacking
Proceed as follows to unpack the unit:
1. Remove packaging.
2. Do not discard the original packaging. Keep it for future relocation.
3. Check the delivery for completeness by comparing it with your order.
4. Please keep the associated paperwork. It contains important
information for handling the unit.
5. Check the contents for visible shipping damage.
6. If you notice any shipping damage or inconsistencies between the
contents and your order, you should notify Beckhoff Service.
Installation Instructions
12 CP72xx
Installation of the Panel PC
The Panel PC series CP72xx is designed for mounting arm installation. A
Control Panel is installed in the front of the IP65 Panel PC.
The ambient conditions specified for operation must be observed (see the
section Technical data).
Note
Circulation of air
When the unit is installed in an enclosure, adequate space for ventilation
and for opening the PC must be provided.
Please note the following points during installation of the PC:
• Position the PC in such a way that reflections on the screen are
avoided as far as possible.
• Use the position of the screen as a guide for the correct installation
height; it should be optimally visible for the user at all times.
• The PC should not be exposed to direct sunlight.
Attention
Avoid extreme environmental conditions
Extreme environmental conditions should be avoided as far as possible.
Protect the rear of your PC from dust, humidity and heat.
The clearance above and below the housing must be at least 20 cm in
order to ensure adequate ventilation of the PC.
The cooling ribs of the PC must not be covered.
Mounting arm installation
Rotatable mounting arm
adapter
The industrial PC is designed for mounting arm installation using a 48 mm
diameter mounting arm tube. The case features an integrated rotatable
mounting arm adapter.
Rotatable and tiltable
mounting arm adapter
(optional)
The swivelling range of the tiltable
mounting arm adapter (optional) amounts
to approx. 45°.
~45°
Installation Instructions
CP72xx 13
Mounting arm installation
For Installation the Industrial PC at the mounting arm, first push back the
red ring cover (1) (see arrows).
Now you get access to the allen head screws (2), with which the mounting
arm tube is fixed in the adapter.
The picture shows the rotatable and tiltable mounting arm adapter
(optional).
Earthing measures
Earthing measures
Earthing connections dissipate interference from external power supply
cables, signal cables or cables to peripheral equipment.
The picture shows the earthing connection in the wiring area of the PC
(see arrow). The earthing cable is laid through the support arm.
1
2
Installation Instructions
14 CP72xx
Power Supply Connection
Supplied mains power unit
The Industrial PC is fitted with a 24 V
DC
power supply unit .
Note
Uninterruptible power supply (UPS)
When the Industrial PC is provided with a power supply unit with
integrated UPS (order option) you can realize an uninterruptible power
supply (UPS) using the battery pack C9900-U330.
WARNING
Danger of Explosion!
Danger of Explosion if using other battery packs!
Beckhoff power supply technology
Schematic diagram of
power supply unit wirings
Innovative solution for
shutting down Industrial
PCs
Industrial PCs equipped with a UPS are in actual use frequently switched
off by simply turning off the supply voltage. In this case the PC shuts down
via the battery. However, over time this reduces the service life of the
battery.
The new Beckhoff power supply technology approach addresses this
problem and now offers the user the option of switching the PC off without
the need for using the battery, thereby reducing the load on the battery.
In addition to the main switch this innovative solution uses an ON/OFF
switch for the machine. Basically, the main switch remains switched on and
provides the power supply for the PC during shutdown.
Once the PC has shut down, the PC power supply unit issues a signal to
indicate that the process is complete and that the main voltage can be
switched off. This can be done manually via a signal lamp connection or
via a contactor. With this solution the main switch generally only has to be
switched off if the control cabinet has to be opened.
Installation Instructions
CP72xx 15
In order to maintain a screen display for the Industrial PC in the event of a
power failure, the power supply unit is equipped with a UPS output for
connecting a Control Panel. This enables a power failure to be visualised
and displayed to the user. Once the PC has shut down, the UPS output is
switched off in order to avoid total discharge of the battery.
Note
Internal connection
The UPS output of the CP72xx power supply unit is internally connected
with the panel
For a detailed functional description please refer to section Connecting
Power Supply.
Pin assignment of the power supply connector
X101
Connector 12-pole Coninvers RC-12P1N1126000
View connector-sided
The power supply connection of the Panel PC and the connection with the UPS (optional) is established
via the 12-pole power supply socket (X101). The protection class of the circular plug-in connector accords
to the IP65-standard.
Wiring when using 8-core cables:
Pin
Wire
Function
Pin
Wire
Function
1
1
-
Battery Pack
(with UPS)
7
6
PC_ON
2
2
+
8
7
Power-Status
3
3
NC
9
-
NC
4
ge/gn
10
-
NC
5
4
-
24 V DC Power Supply
11
-
NC
6
5
+
12
-
NC
Wiring when using 12-core cables:
To connect the power supply and the battery pack, 2 wires per pin are used when using 12-core cables to
halve the voltage drop across the cable.
Pin
Wire
Function
Pin
Wire
Function
1
1, 8
-
Battery Pack
(with UPS)
7
6
PC_ON
2
2, 9
+
8
7
Power-Status
3
3
NC
9
-
NC
4
ge/gn
10
-
NC
5
4, 10
-
24 V DC Power Supply
11
-
NC
6
5, 11
+
12
-
NC
Installation Instructions
16 CP72xx
Pin assignment CP72x4 with 24-inch display (discontinued)
Pin assignment for
connecting the power
supply, the switch and the
battery pack (optional)
View connector-sided
Connector 12-pole Coninvers
RC-12P1N1126000
Pin
Wire
Function
1
1
-
Battery Pack
(with UPS)
2
2
+
3
3
NC
4
ye/gn
5
4
-
24 V DC Power Supply
PC Unit
6
5
+
7
6
PC_ON
8
7
Power-Status
9
8
-
Battery Pack
(with UPS)
10
9
+
11
10
-
24 V DC Power Supply
Display
12
11
+
Pre-assembled cable sets for the power supply
Pre-assembled power
supply cables
For easy installation of the power supply there are pre-assembled
connection cables of different length and with IP65 connectors available
(see table).
Order number
Denomination
C9900-K271
Power supply cable IP65 for CP72xx, length 5 m, pre-
assembled, M23-female connector, screwable, 8-wire,
second end open
C9900-K272
Power supply cable IP65 for CP72xx, length 10 m, pre-
assembled, M23-female connector, screwable, 8-wire,
second end open
C9900-K275
Power supply cable IP65 for CP72x4 with 24-inch display,
length 5 m, pre-assembled, M23-female connector,
screwable, 12-wire, second end open
C9900-K276
Power supply cable IP65 for CP72x4 with 24-inch display,
length 10 m, pre-assembled, M23-female connector,
screwable, 12-wire, second end open
C9900-K277
Power supply cable IP65 for CP72xx up to 19-inch display,
length 20 m, pre-assembled, M23-female connector,
screwable, 12-wire, second end open
Fitting the power supply cable with IP65 connector
Basic configuration without
connecting cable and
connector
In the basic configuration of the Industrial PC there is no connection cable
provided for connecting the power supply. For connecting the power supply
following connectors can be used:
Cable 8-pole for CP72xx
Coninvers female connector Series RC 12-pole
(Crimp Coninvers RM-12S1N8A1100, Coninvers Connector 12-pole, with
metric screw connection M16)
Cable 12-pole for CP72x4 (discontinued)
Coninvers female connector Series RC 12-pole
(Crimp Coninvers RM-12S1N8A1300, Coninvers Connector 12-pole, with
metric screw connection M20)
The connectors and special tools for the assembly are available via the
company Coninvers http://www.coninvers.com as well as different
distributors.
Male
connector
Installation Instructions
CP72xx 17
Connecting Power Supply
The external wiring consists of the connection of the power supply, the
battery pack (optional) and the connection of customised components for
shutting down the PC.
Cable Cross Sections
Note cable cross sections,
avoid voltage drop!
For the connection of the power supply, wiring with a cable-cross-section
of 1.0 mm
2
must be used.
With bigger distances between voltage source and PC, you take the
voltage drop as a function of the cable-cross-section as well as voltage
fluctuations of your distribution voltage into account, so that is secured that
the voltage doesn't fall under 22 V at the power supply.
Attention
Insert fuse
The power supply must be protected with maximum 10 A.
Configuration for shutting down the PC
The connections for shutting down the Industrial PCs are established via
the PC_ON input and the Power Status output.
PC_ON and Power Status functions
• If the PC_ON input is connected to 24 V via a switch, the PC shuts
down according to the rules. The PC_ON signal is inverted, i.e. the
PC shuts down if the 24 V connection is live.
• If the PC_ON input is NOT connected by the user, the PC can be
booted in the familiar way by connecting the supply voltage and shut
down via the battery by switching off the supply voltage.
Attention
Service life of the rechargeable battery
This procedure significantly reduces the service life of the rechargeable
battery and should therefore not be used.
• Once the PC has shut down, the Power Status output is switched
from 24 V to 0 V. Via this output a signal lamp can be connected or a
contactor for de-energising the whole system. The maximum load for
the Power Status output is 0.5 A and a suitable fuse should be
provided.
Installation Instructions
18 CP72xx
Wiring diagram CP72xx
Wiring according to the wiring diagram (the circuit of PC_ON and Power-
Status is symbolical):
Wiring diagram power
supply and external wiring
Note
Connection of the Battery Pack
Connection of the Battery Pack in combination with integrated UPS (order
option).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Beckhoff Economy CP213-0001 Installation And Operating Instructions Manual

Brand
Beckhoff
Model
Economy CP213-0001
Category
Uninterruptible power supplies (UPSs)
Type
Installation And Operating Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents