Daewoo DVQ 9H1FC User manual

Brand: Daewoo

Model: DVQ 9H1FC

Category: Cassette players

Type: User manual

This manual is also suitable for

DVQ-9H1FC

INSTRUCTION MANUAL

TV/VCR COMBINATION

DVQ 9H1FC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intend-

ed to alert the user to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to constitute a risk electric

shock.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and servicing instructions in the literature

accompanying the appliance.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER

THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION

TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUND-

ING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECT-

ED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF

CABLE ENTRY AS PRACTICAL.

CAUTION

The AC power cord provided with this product is polarized (one blade wider than the other).

To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a

standard 120V~, 60Hz polarized outlet.

NOTE

Never connect the plug to an electrical source other than one providing 120V~ 60Hz power. Use only

the attached power cord. If the polarized AC cord does not fit into a non-polarized outlet, do not cut or

file the blade. You are responsible for having the obsolete outlet replaced with a polarized outlet.

If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the

unit from the outlet. When you plug the unit back in, it should work normally.

Do not install power cords near any heating element or cooking appliances.

SAFETY PRECAUTIONS

LOCATION

For safe operation and satisfactory performance of your unit,

keep the following in mind when selecting a place for its instal-

lation :

• Never leave the TV/VCR in areas exposed to temperature

extremes or strong direct sunlight. Leaving it in closed car, in

direct sunlight, near a heater, etc. can cause deformation of

the case.

• Avoid dusty or humid place.

• Avoid place with insufficient ventilation for proper heat dissi-

pation. Do not block the ventilation holes at the top and bot-

tom of the unit. Do not place the unit on a carpet because this

will block the ventilation holes.

• Install the unit in a horizontal position.

• Avoid locations subject to strong vibration.

• Do not place the unit near strong magnetic fields.

• Do not move the unit from a cold place to a hot place or vice

versa(see the warning below).

HANDLE WITH CARE

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from an

AC wall outlet. Grasp it by plug.

• If, by accident, water is spilled on your unit, unplug the

power cord immediately and take the unit to an authorized

DAEWOO service center for servicing.

• Do not put your fingers or objects into the TV/VCR cassette

holder.

• Do not place anything directly on the top of the unit.

WARNING

Moisture condensation may occur inside the unit when it is

moved from a cold place to a warm place, after heating in a

cold room, or under conditions of high humidity. If a tape is

played in a TV/VCR that has moisture, it may damage the tape

and TV/VCR. When condensation occurs inside the unit, turn

the power on and allow at least 2 hours for the unit to dry. This

equipment is not operated under conditions of high humidity.

FCC WARNING

This equipment may generate or use radio frequency energy.

Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in

the instruction manual..

The user could lose the authority to operate this equipment if

an unauthorized change or modification is made.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast television pro-

gramming, video tape, film, or other copyrighted material may

violate applicable copyright laws. We assume no responsibility

for the unauthorized duplication, use or other acts which

infringe upon the rights of copyright owners.

IMPORTANT NOTES:

• The unit is designed for use with a 12V DC automotive

power supply. Never use it in a truck, bus, or any othe car that

has a 24V power supply.

• Be sure to stop your car in a safe area before watching or

adjusting the TV/VCR.

• Operating the TV/VCR for a long time with the engine of

your car stopped can run down your car’s battery.

• Should the TV/VCR ever begin to emit smoke, abnormal

odor, or a strange noise, immediately turn off power and

unplug the unit from the cigarette lighter socket. Continued

use of the TV/VCR under any of these conditions creates the

danger of fire and electric shock.

• Do not continue to use the TV/VCR if it is malfunctioning

and does not produce a video image or sound. Whenever you

notice such symptoms, immediately turn off power, unplug

the TV/VCR from the cigarette lighter socket. Continued use

of the TV/VCR creates the danger of fire and electric shock.

• When you leave your car unattended for long periods, be sure

to unplug the TV/VCR from the cigarette lighter socket.

Leaving the TV/VCR plugged in can run down the car’s bat-

tery.

INSTALL THE TV/VCR IN YOUR CAR

• For a car equipped with air bags, be sure to follow the manu-

facturer’s instructions whenever performing any electrical

wiring work. Incorrect wiring can cause the air bag system of

a car malfunction.

• Never cut the insulation form the power supply lead in an

attempt to draw power for another device. Doing so can over-

load the current capacity of the lead, creating the danger of

fire and electric shock.

• For proper installation and wiring, special technical knowl-

edge is required. If you have any doubts about where to posi-

tion or how to install components, contact the retailer where

you purchased the product, your automobile dealership, or an

automotive service provider. Note that you will be charged

separately for installation work.

• Improper installation creates the danger of fire and accident.

• Avoid installation in areas subject to strong vibration and

areas where secure anchoring cannot be achieved.

Components installed in such areas can work loose, creating

the danger of accident and personal injury.

• Never install the TV/VCR on the dashboard or in any other

location where it obstructs forward vision. Items that obstruct

forward vision in a motor car may be illegal. Improper instal-

lation creates the danger of traffic accident and personal

injury.

• Never attach the stand to the roof of your car. Doing so cre-

ates the danger of the TV/VCR falling down.

• Never attach the stand to a sharply angled surface or to a sur-

face that causes the TV/VCR to face downloads. Such instal-

lation can cause the TV/VCR to fall.

• Be sure to turn the ignition key of the car to the “OFF” posi-

tion before connecting or disconnecting wires and cables.

Failure to do so creates the danger of electric shock and per-

sonal injury.

DRIVING SAFETY

• Never watch the TV/VCR or try to adjust settings while dri-

ving. Doing so creates the danger of traffic accident. Before

operating the TV/VCR, be sure to stop the car in a safe area..

• Make sure all cables are bundled together so they do not

interfere with car operation, as described in this manual.

Improperly installed cables create the danger of entanglement

with the steering wheel, shift lever, brake pedal, etc.

SAFETY

IMPORTANT SAFEGUARDS

PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT

AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS

MARKED ON THE TV RECEIVER.

1 Read all of these instructions.

Save these instructions for later use.

Unplug this television equipment from the

wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

Do not use attachments not recommended by

the television equipment manufacturer as

they may result in the risk of fire, electric

shock or other personal injury.

Do not use this television equipment near

water, for example, near a bathtub, wash-

bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool, or the

like.

Do not place this television equipment on an

unstable cart, stand, or table. The television

equipment may fall, causing serious injury to

a child or adult, and serious damage to the

equipment. Use only with a cart or stand rec-

ommended by the manufacturer, or sold with

the television equipment. Wall or shelf

mounting should follow the manufacturer's

instructions, and should use a mounting kit

approved by the manufacturer.

An appliance and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

appliance and cart combination to overturn.

Slots and openings in the cabinet and the

back or bottom are provided for ventilation

and to ensure reliable operation of the televi-

sion equipment; and to protect it from over-

heating, these opening, must not be blocked

or covered. The opening should never be

blocked by placing the television equipment

on a bed, sofa, rug, or other similar surface.

(This equipment should never be placed near

or over a radiator or heat register.) This tele-

vision equipment should not be placed in a

built-in installation such as a bookcase

unless proper ventilation is provided.

This television equipment should be operat-

ed only from the type of power source indi-

cated on the marking label. If you are not

sure of the type of power supplied to your

home, consult your television dealer or local

power company.

This television equipment is equipped with a

polarized alternating current line plug (a plug

having one blade wider than the other). This

plug will fit into the power outlet only one

way. This is a safety feature. If you are

unable to insert the plug fully into the outlet,

try reversing the plug. If the plug should still

fail to fit, contact your electrician to replace

your obsolete outlet. Do not defeat the safety

purpose of the polarized plug.

Do not allow anything to rest on the power

cord. Do not locate this television equipment

where the cord will be abused by persons

walking on it.

Follow all warnings and instructions marked

on the television equipment.

For added protection for this television

equipment during a lightning storm, or when

it is left unattended and unused for long peri-

ods of time, unplug it from the wall outlet

and disconnect the antenna or cable system.

This will prevent damage to the equipment

due to lightning and power-line surges.

PORTABLE CART WARNING

S3126A

An outside antenna system should not be

located in the vicinity of overhead power

lines or other electric light or power circuits,

or where it can fall into such power lines or

circuits. When installing an outside antenna

system, extreme care should be taken to

keep from touching such power lines or cir-

cuits as contact with them might be fatal.

Do not overload wall outlets and extension

cords as this can result in fire or electric

shock.

Never push objects of any kind into this tele-

vision equipment through openings as they

may touch dangerous voltage points or

short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind

on the television equipment.

Do not attempt to service this television

equipment yourself as opening or removing

covers may expose you to dangerous volt-

age or other hazards. Refer all servicing to

qualified service personnel.

Unplug this television equipment from the

wall outlet and refer servicing to qualified

service personnel under the following condi-

tions:

(a) When the power-supply cord or plug is

damaged or frayed.

(b) If liquid has been spilled, or objects have

fallen into the television equipment.

to rain or water.

(d) If the television equipment does not operate

normally by following the operating instruc-

tions. Adjust only those controls that are cov-

ered by the operating instructions as an

improper adjustment of other controls may

result in damage and will often require exten-

sive work by a qualified technician to restore

the TV receiver to its normal operation.

(e) If the television equipment has been dropped or

the cabinet has been damaged.

(f) When the television equipment exhibits a

distinct change in performance - this indi-

cates a need for service.

When replacement parts are required, be

sure the service technician has used replace-

ment parts specified by the manufacturer

that have the same characteristics as the

original part. Unauthorized substitutions

may result in fire, electric shock or other

hazards.

Upon completion of any service or repairs to

this television equipment, ask the service

technician to perform safety checks to deter-

mine that the television is in a safe operating

condition.

If an outside antenna or cable system is con-

nected to the television receiver, be sure the

antenna or cable system is grounded so as to

provided some protection against voltage

surges and built-up static charges.

Section 810 of the National Electrical Code,

ANSI/NFPA N0.70-1984, provides informa-

tion with respect to proper grounding of the

mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of

antenna-discharge unit, connection to

grounding electrodes, and requirements for

the grounding electrode.

Table of Contents

Preface : Your New TV/VCR

Features 2

Unpacking Your TV/VCR 3

Chapter 1 : Overview of Your Equipment 4

Your TV/VCR’s Front Panel 4

Your TV/VCR’s Back Panel 5

Your Remote Controller 6

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR 9

Connecting an Antenna 9

Connecting a Cable System 11

Connecting Other Pieces of Equipment 12

Safety Notes 12

Chapter 3 : Operating Your TV 13

Turning Your TV/VCR On 13

Programming Your TV/VCR’s Channel Memory 13

Changing channels 14

Changing the Volume 14

Changing the TV/VCR’s Channel Memory 15

Displaying the TV/VCR’s Status during TV operation 15

Adjusting Video Settings 16

Chapter 4 : Operating Your VCR 18

Video Cassette Tapes 18

Playing a Tape 19

Basic Recording 20

One Touch Recording (OTR) 21

Displaying the TV/VCR’s Status during VCR Operation 22

Using the Counter (Zero Stop) 23

Chapter 5 : Using Timer Functions 24

Setting the Clock Automatically 24

Setting the Clock Manually 25

Setting the On Time 26

Setting the Off Time 26

Canceling the On Time or Off Time 27

Setting the Sleep Timer 28

Chapter 6 : Additional TV Features 29

Changing the Language of the On-Screen Menus 29

Captioning 29

CC on Mute 30

Power Restore 30

Parental Control Settings 31

Description of Parental Control Settings 32

Mini Glossary 33

Chapter 7 : Additional VCR Features 34

Programming to Record at a Later Time 34

Setting the Program Recording 35

Canceling the Program Record Settings 37

Displaying the Tape Counter 38

Auto Repeat PlayBack 39

Rental Play 39

Index Search (VISS) 40

Duplicating a Video Tape 41

Chapter 8 : Troubleshooting 42

Mainternance and specifications

Warranty

CONTENTS

Preface : Your New TV/VCR

PREFACE

Your New TV/VCR

Congratulations on your purchase of a new Daewoo TV/VCR. We hope you find that your

new TV/VCR provides you with years of reliable performance.

Your new TV/VCR is designed and engineered to provide you with the latest in features for

your convenience. Listed below are just a few of the many features of your equipment.

Features

• Auto Power On

This feature automatically turns the TV/VCR on when you insert a cassette.

• On-screen Programming

You can use simple on-screen menus to perform all of the major operating features of your

TV/VCR, including programming to record.

• Tri-lingual Menus

You can choose to display the on-screen menus in English, French or Spanish.

• Auto Clock Setting

Your TV/VCR can automatically set its internal clock based on a signal from local PBS sta-

tions.

• 120V AC or 12V DC Operation

This TV/VCR is designed to operate from household AC current or from a 12V DC car cig-

arette lighter socket.

• 181 Channel Capability

Your TV/VCR has a advanced tuner that can receive up to 181 channels.

• Closed Caption Decoder

Your TV/VCR can decode the hidden text and captions that are broadcast with many shows

and are included on many videotapes.

• Record/Playback Speeds

Your TV/VCR can recording to two speeds(SP, EP), playback to three speeds (SP, LP, EP).

SP(Standard Play), LP(Long Play), EP (Extend Play)

• Automatic Playback Speed Selection

Your TV/VCR will automatically play a pre-recorded tape at the correct speed.

• Still Frame Capability

Your TV/VCR can display a single frame from a video tape.

• Rental Play Mode

This special setting improves the playback quality of worn tapes, especially rental tapes.

• Repeat Playback

You can set your TV/VCR to automatically repeat an entire video tape, or to repeat the

recorded part of a videotape.

Preface : Your New TV/VCR

• Video Index Search System (VISS)

This feature allows you to find index marks on your tape quickly. Your TV/VCR places

index marks at the beginning of each new recording.

• One Touch Recording (OTR)

You can quickly begin recording and set the length of time to record using just one button.

• 6 Events / 1 Month Timer Recording

You can program up to six different recording sessions up to a month in advance.

• Daily / Weekly Recording

You can easily set your VCR to record every day at the same time, or to record every week

at the same time.

• Sleep Timer

You can set your TV/VCR to turn off after a certain amount of time passes, from 15 min-

utes to 120 minutes.

• On Timer

You can set your TV/VCR to turn on at a certain time.

• Parental Control

Parental control is on the 31 page.

Unpacking Your TV/VCR

The following items are included with your TV/VCR. If these items are missing, please con-

tact your Daewoo dealer immediately.

1 A remote control

2 A 300-ohm/75-ohm adaptor

3 A rod antenna (“rabbit ears”)

4 DC Car Cord

1 2

RECALL

REW PLAY FF

REC/OTR STOP

STILL

VISS

ATK

SLEED

SLOW

3 4

Chapter 1 : Overview of Your Equipment

CHAPTER

Overview of Your Equipment

Your TV/VCR’s comes with a remote control. The section below summarizes the buttons,

controls, and terminals that will use with your TV/VCR’s.

Your TV/VCR's Front Panel

Below you will find short description of the buttons and indicators on the front panel. These

are use following functions.

1 VIDEO in jack

Use this jack to receive a video signal from another A/V component.

2 AUDIO in jack

Use this jack to receive a audio signal from another A/V component.

3 EAR PHONE jack

Use this jack to the earphone (not supplied). The sound from the speaker is turned off.

buttons (channel)

Press these buttons to change channels on your TV/VCR. You will also use these buttons

to adjust the tracking.

VOL

buttons (volume)

Press these buttons to change your TV/VCR’s volume.

6 Remote control receiver

This receiver receives a signal from your remote control. Do not block it.

7 STAND-BY(red) indicator

This indicator light up when the power is off.

8 REC/T.REC (red/green) indicator

This indicator light up red when recording and light up green when timer program operat-

ing.

9 REC button

Press this button to begin recording. Press repeatedly to set a recoding time using

One-Touch Recording (OTR).

10 REW button

Press this button to rewind the tape.

Chapter 1 : Overview of Your Equipment

11 PLAY button

Press this button to begin normal palyback of the tape.

12 FF button (Fast Forward)

Press this button to fast forward the tape.

13 STOP/EJECT button

Press this button when the tape is moving to stop the tape. Press this button when the tape

is stopped to eject it.

14 POWER button

Press this button to turn your TV/VCR on or off.

Your TV/VCR’s Back Panel

1 Antenna terminal

Use this terminal to attach an antenna or cable system to your TV/VCR.

2 AC Power Cord

Connect to a 120V, 60Hz outlet.

3 DC Input Jack

Connect the 12V DC car cord(supplied) here for DC operation. The connection method of this

jack and DC car cord is shown above.

Notes

FOR USE BATTERY CONNECTING MEANS, Hyo Sung Electronics Co.,

CAT. NO. DLP-1033, BATTERY ADAPTOR ONLY.

FOR USE WITH ANY LISTED BATTERY CONNECTING MEANS WITH 8A 125V

OR 250V FUSE.

To DC Input Jack

Car Cord(supplied)

To Cigarette Lighter Socket

123

Your Remote Controller

1. POWER

Press this button to turn your TV/VCR on or off.

2. RECALL

Press this button to display the current time, the

counter, channel number and other status items.

3. TV/LINE

Press this button to select between viewing the

signal coming from the antenna terminal (TV) or

the signal coming from the A/V jack (LINE).

4. FAVORITE CH

Press this button to return to the previous channel

you were watching.

5. CANCEL

Press this button to erase timer program recording

settings.

6. C-RESET

Press this button to reset the counter to 0:00:00.

7. MUTE

Press to turn the TV/VCR’s sound on and off.

(TRK)

Press these buttons to change channels on your

TV/VCR, or select items in the menu system, or

to adjust the tracking of a video tape during play-

back.

VOL

Press these buttons to change your TV/VCR’s

volume, to activate selections in the menu system,

or to change audio and video settings.

Chapter 1 : Overview of Your Equipment

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP/EJECT PAUSE/STILL

VISS VISS

C H

VOL

C H

0 ATK

SPEED C- STOP

Chapter 1 : Overview of Your Equipment

10. MENU

Press this button to turn the TV/VCR’s menu system on and off.

11. 0-9

Press these buttons to change channels.

12. SPEED

Press this button to select the SP, EP tape speed when the tape recording.

13. C-

STOP

Press this button to find the counter zero.

14. 0(ATK)

Press this button to automatically set tracking point when the tape playback.

15. REW

Press this button to rewind the tape.

17. FF button (Fast Forward)

Press this button to fast forward the tape.

18. PAUSE/STILL

Press to temporarily stop the tape during recording or playback.

19. REC/OTR

Press this button to begin recording. Press repeatedly to set a recording time using

One-Touch Recording (OTR)

20. STOP/EJECT

Press this button when the tape is moving to stop the tape. Press this button when the tape

is stopped to eject it.

21. VISS -

Press this button to find the most recent index mark on tape and begin playing.

22. VISS +

Press this button to find the next index mark on tape and begin playing.

Chapter 1 : Overview of Your Equipment

Installing Your Remote Control Batteries

Open the battery compartment on the back of the remote control.

Install two AAA-size batteries (not included) as shown. Make sure the “+” and “-” terminals

are oriented correctly.

Replace the cover.

Notes

Do not mix different types of batteries together or old batteries with fresh ones.

Remove and replace weak batteries. Weak batteries can leak and damage your controller.

Dispose of batteries properly; never throw them into a fire.

Point your remote at the receiver on the center of the front of the TV/VCR. Make sure the

receiver is not blocked.

The remote control can operate up to 30 feet away from the TV/VCR, if you are directly fac-

ing the front of the TV/VCR. Operating distance diminishes as you move to the sides of the

TV/VCR.

To use DC power

By using the DC car cord supplied with the TV/VCR, you can operate this TV/VCR from a

cigarette lighter socket in any car that utilizes a negative ground system.

The fused 12V DC car cord has been designed to power the set from the external DC power

(12 volt negative ground) through the TV/VCR DC Input jack.

If the fuse in the car cord plug blows, replace it with a new 8 A fuse (Fast Blow Type) as

shown below. Unscrew the tip of the plug to remove.

Notes

Always turn off TV/VCR first before switch ON or OFF the ignition of car engine.

Make sure that the negative terminal of the battery is grounded.

When the TV/VCR is not in use, always disconnect it from the car cigarette lighter socket to

avoid a battery drain.

Do not operate the TV/VCR if the car battery is weak. Peak current from the car alternator

could blow the DC fuse.

Check the battery's charge level regularly when the TV/VCR is used in a vehicle.

CHAPTER

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR

Connecting an Antenna or Cable to Your TV/VCR

Your TV/VCR will provide you with the best performance if you connect it to an external

antenna or cable system. Follow the directions below make this connection. Please note that

you will normally only have to make one of the connections shown below, not all of them.

All connections will be made to the antenna terminal on the back of your TV/VCR. The

antenna terminal is a silver metal post partially surrounded by two plastic tabs. For help in

locating the antenna terminal, see “Your TV/VCR's Back Panel” on page 5.

There is no antenna provided with your TV/VCR.

Connecting an Antenna

If your antenna ends in a single coaxial lead,

simply press or screw the cable onto the antenna

terminal on the back of your TV/VCR.

If your antenna ends in a pair of 300 ohm twin leads, you must use a 300-ohm/75-ohm

adaptor. (An adaptor is included with your TV/VCR.) Place the leads underneath the screws

on the adaptor, tighten the screws, then press the adaptor onto the antenna terminal on the

back of the TV/VCR.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR

Antennas with two sets of leads

You might have two sets of leads from your antenna system, especially if you have one anten-

na for VHF signals and one antenna for UHF signals.

If your antenna system has both a coaxial lead and twin 300-ohm leads

, you must obtain a com-

biner (available at your local electronics store). Press or screw the coaxial lead onto the com-

biner; place the twin leads underneath the screws on the combiner and tighten the screws.

Press the cable from combiner onto the antenna terminal on the back of the TV/VCR.

If your antenna system has two sets of twin 300-ohm leads, you must obtain a combiner

(available at your local electronics store). Place one set of twin leads underneath the screws on

the combiner and tighten the screws. Do the same with the other set of twin leads. Press the

cable from the combiner onto the antenna terminal on the back of your TV/VCR.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR

Connecting a Cable System

If your cable set-up is not described below, please contact your cable company for more infor-

mation.

If your cable system does not require the use of a

cable box, simply press or screw the incoming cable

onto the antenna terminal on the back your TV.

If your cable system requires you to use a converter box for all channels, connect the

incoming cable to the IN terminal on the converter box. Connect another cable between the

OUT terminal on the converter box and the antenna terminal on the TV. You will need to

keep your TV tuned to channel 3 or 4 and change channels using the converter box.

If your cable system only requires you to use a converter box for some channels (i. e.

pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this

cable into a splitter (available at your local electronics store). Connect one coaxial cable

between one OUT terminal on the splitter and the IN terminal on the converter box. Connect

another coaxial cable between the other OUT terminal on the splitter and the A-IN terminal on

an A/B switch (available at your local electronics store.) Connect a third coaxial cable

between the OUT terminal on the converter box and the B-IN terminal on the A/B switch.

Finally, connect a coaxial cable between the OUT terminal on the A/B switch and the antenna

terminal on the back of your TV/VCR.

When the A/B switch is in the A position, you can change channels on the TV/VCR; when

the A/B switch is in the B position, you, need to change channels on the converter box (and

your TV should be tuned to channel 3 or 4)

Connecting Other Pieces of Equipment

You may want to connect a VCR, laser disc player, satellite receiver, or another type of equip-

ment to your TV/VCR. We recommend that you follow the instructions included with the

piece of equipment you wish to connect.

If you connect other pieces of equipment to your TV/VCR using the audio/video jacks on the

front panel, you will need to use the TV/LINE button on the remote control to view the signal

coming through these jacks. See page 41 for more information.

Safety Notes

If you plan on being away from your home for an extended period of time, or if a thunder-

storm is approaching, you should unplug your television, and you may wish to disconnect

your TV from a rooftop or satellite antenna. You do not need to disconnect your TV from a

cable system.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR

Chapter 3 : Operating Your TV

CHAPTER

Operating Your TV

Once you have connected your TV/VCR to an antenna or cable system, plugged the TV in,

and put batteries in the remote, you are ready to use the TV. The first thing you should do is

program your TV/VCR so it memorizes all of available channels.

Turning Your TV/VCR On

To turn your TV/VCR on, press the POWER button on the remote

control. You can also use the POWER button on the front panel.

Make sure your TV is plugged in before you try to turn it on.

Programming Your TV/VCR's Channel Memory

Your TV/VCR's memory determines the channels that are available using the

but-

tons. If a channel is not in memory, you can tune to it with the number buttons, but not with

the

buttons. Follow these steps to program your TV/VCR's memory:

With the TV on, press the MENU button until “Set-Up”menu will be displayed.

Use the

buttons to select “Reception”, then use the VOL

button to select ‘Air’

or ‘Cable’. If you connected an antenna to your TV/VCR, select ‘Air’; If you connected a

cable system, select ‘Cable’.

Use the

buttons to select “Memorize Channels”, then use the VOL

button to

enter the “Memorize Channels” process.

Press the MENU button to return to Set-Up menu.

Press the MENU button to return to normal TV viewing.

Your TV/VCR's channel memory will not be affected by a power outage. You will not need to

re-program the memory unless you change the type of cable or antenna connected to your

TV/VCR.

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Adjust Exit

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Enter Exit

3-1

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Adjust Exit

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Enter Exit

Set-Up

Chapter 3 : Operating Your TV

Changing Channels

You can change channels in three ways:

The

buttons will take you through all memorized

channels, one by one. The

buttons will not access chan-

nels that have not been programmed into the TV's memory. For

more information about programming channels into memory,

see the section “Programming your TV/VCR's Channel

Memory” on the previous page.

The number buttons (0-9) will take you to any channel, even if it

has not been memorized. To change to a channel, enter its num-

ber; the TV/VCR will tune to the new channel when you enter

the second digit of the channel.

The FAVORITE CH button will take you instantly to the last

channel you were watching.

Changing the Volume

To change the volume of the TV/VCR set, use the

VOL

but-

tons on the remote or on the front panel.

To quickly turn off the sound, press the MUTE button on the

remote. The ‘MUTE’ will appear on screen, colored red. To

return the volume to its previous level, press MUTE again.

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

R-39N01

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

Chapter 3 : Operating Your TV

Changing the TV/VCR's Channel Memory

Your TV/VCR's memory determines the channels that are available using the

but-

tons. You can add channels to this memory or remove them from memory. If a channel is

removed from memory, you can tune to it with the number buttons, but you cannot tune to it

with the buttons.

If there are just one channel memorized, then the Add/Delete Channels function will search

the whole channels. But if there are two or more channel memorized, then the Add/Delete

Channels function will search the memorized channels only.

Adding/Deleting a channel to memory

Use the number buttons to tune to the channel.

Press the MENU button until “Set-Up” menu will be displayed

Use the

buttons to select “Add/Delete Channels”, then use the VOL

button to

enter the “Add/Delete Channels” process.

If the channel is not in memory, then use the

VOL

buttons to add the channel from

memory.

If the channel is in memory, then use the

VOL

buttons to delete the channel from

memory.

If you are going to delete other channel, then press the xCHy buttons until desired chan-

nel is selected. And press the CVOLB buttons to delete the channel.

Press MENU to exit.

Displaying the TV/VCR’s Status during TV Operation

To quickly see the current channel number and status, press RECALL button

on the remote control.

The current channel number and status will be displayed.

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Enter Exit

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Adjust Exit

Set-Up

Add/Delete Channels

Air 11

This channel is not in memory.

Press VOL to add.

Press CH or [0-9]

for other channels.

Press MENU to return

to Set-Up menu.

Add/Delete Channels

Air 16

This channel is in memory.

Press VOL to delete.

Press CH or [0-9]

for other channels.

Press MENU to return

to Set-Up menu.

Add/Delete Channels

Air 11

This channel is in memory.

Press VOL to delete.

Press CH or [0-9]

for other channels.

Press MENU to return

to Set-Up menu.

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

Page is loading ...

Daewoo DVQ 9H1FC User manual

Brand: Daewoo

Model: DVQ 9H1FC

Category: Cassette players

Type: User manual

This manual is also suitable for

DVQ-9H1FC

Download PDF

report

Daewoo DVQ 9H1FC User manual

This manual is also suitable for

Daewoo DVQ 9H1FC User manual

Related papers

Other documents