Epson ELP-3300 User manual

i

EPSON

®

Owner’s Manual

ii

or transmitted in any form or by any means, electronic, mechanical, photocopying, recording,

or otherwise, without the prior written permission of Seiko Epson Corporation. No patent

liability is assumed with respect to the use of the information contained herein. Neither is any

liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this

product or third parties for damages, losses, costs, or expenses incurred by purchaser or third

parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications,

repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with

Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the

use of any options or any consumable products other than those designated as Original EPSON

Products or EPSON Approved Products by Seiko Epson Corporation.

EPSON is a registered trademark of Seiko Epson Corporation.

EPSON Connection is a service mark of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may

be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.

The Energy Star emblem does not represent EPA endorsement of any product or service.

Torrance, California, USA 2/96

iii

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this

device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the

responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has

more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not

expressly approved by the manufacturer could void the user’s authority to operate the equipment.

DOC (for Canadian Users)

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment regulations.

Cet appareil numérique de la Classe A respecte toutes les exigences du Réglement sur le materiel brouilleur du Canada.

Apple Warranty Disclaimer

Apple Computer, Inc. (“Apple”) makes no warranties, express or implied, including without limitation the implied

warranties of merchantability and fitness for a particular purpose, regarding the Apple software. Apple does not warrant,

guarantee or make any representations regarding the use or the results of the use of the Apple software in terms of its

correctness, accuracy, reliability, currentness or otherwise. The entire risk as to the results and performance of the Apple

software is assumed by you. The exclusion of implied warranties is not permitted by some states. The above exclusion may

not apply to you.

In no event will Apple, its directors, officers, employees or agents be liable to you for any consequential, incidental or

indirect damages (including damages for loss of business profits, business interruption, loss of business information, and

the like) arising out of the use or inability to use the Apple software even if Apple has been advised of the possibility of

such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental

damages, the above limitations may not apply to you. Apple’s liability to you for actual damages from any cause

whatsoever, and regardless of the form of the action (whether in contract, tort (including negligence), product liability or

otherwise), will be limited to $50.

Energy Star Compliance

EPSON is an Energy Star Partner and this projector complies with the Energy Star program's

guidelines for energy efficiency.

iii

Important Information About Your ELP-3300

Please read the following important information about your ELP-3300 projector.

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on;

the bright light can damage your eyes. Never let children look into the lens

when it is on.

WARNING: Never open any cover on the projector, except the lamp, fuse, and

filter covers. Dangerous electrical voltages inside the projector can severely

injure you. Except as specifically explained in this Owner’s Manual, do not

attempt to service this product yourself. Refer all servicing to qualified

service personnel.

Caution: When you replace the lamp, never touch the new bulb with your

bare hands; the invisible residue left by the oil on your hands may shorten

the bulb life. Use a cloth or glove to handle the new bulb.

Remote Control Information

The ELP-3300 allows you to operate it by remote control via infrared (IR)

receivers located at the front and back of the projector. The projector may not

respond to remote control commands under the following conditions:

• The ambient light is too bright

iv

• Certain types of fluorescent lighting are used

• A strong light source shines into either IR receiver

• Other equipment that emits infrared energy, such as a radiant room heater, is

in the room.

These conditions commonly cause problems for most infrared-controlled

equipment. Try the following solutions:

• The remote control unit’s batteries may be low on power; replace them.

• Dim the ambient lighting and/or turn off any fluorescent lights.

• Close any window coverings and/or move the projector out of direct sunlight.

• Turn off other equipment that emits infrared energy.

If the remote control still does not work properly, cover the unused IR receiver

on the projector with light-blocking material, such as masking tape. Remember

you can always control your computer-based presentation directly from the

computer, even in an environment containing one of the conditions listed above.

README File Information

The diskettes that came with your projector include README files that contain

additional important information about the projector. Be sure to read these files.

Contents

v

Contents

Introduction

ix

Getting the Most Out of Your Projector x

Optional Accessories xii

About This Manual xiii

Safety Instructions xiv

Where to Get Help xvi

Electronic support services xvii

Energy Star Compliance xviii

1 Installation 1

Unpacking the Projector 2

Additional components 3

Setting Up the Projector 4

Connecting to a Computer 6

Connecting to a PC desktop computer 7

vi

Contents

Connecting to a PC laptop computer 8

Connecting to a desktop Macintosh 9

Connecting to a PowerBook 10

Connecting to a Video Source 11

Connecting to an Audio Source 13

Connecting to an External Speaker or PA System 14

Setting Up Serial Communication 15

Connecting the serial cable 15

Installing the software 16

Connecting the Remote Control with the Lead Wire 17

2 Using the Projector 19

Turning the Equipment On and Off 20

Focusing and Positioning the Screen Image 21

Controlling the Projector 23

Adjusting the settings from ELP Link 26

Monitoring the Projector 27

Using Rear Projection 28

3 Using the Menus 29

Accessing the Menus 30

Changing menu settings 31

Accessing ELP Link menus 32

Restoring the default settings 33

Menu Settings 33

Contents

vii

Computer menu 34

Video menu 36

Display menu 37

Audio menu 39

Options menu 40

Custom menu 41

4 Remote Control of the Computer 43

ELP Remote Programmer Templates 44

Starting the ELP Remote Programmer 45

Assigning a Macro to a Programmable Button 48

Using record mode 49

Using manual mode 51

Activating a Template 51

ELP Remote Programmer Menus 52

5 Maintenance 53

Cleaning the Lens 54

Cleaning the Projector Case 54

Cleaning the Air Filter 54

Cleaning the Trackball 56

Replacing the Lamp 58

Resetting the lamp timer 61

Replacing the Fuse 62

viii

Contents

6 Troubleshooting 65

Problems with the Projector 66

Problems with the Image or Sound 69

Problems with the Remote Control 72

A Technical Specifications 75

General 75

Optical 76

Projector Lamp 76

Mechanical 76

Electrical 77

Environmental 77

Supported Monitor Displays 78

Pin Assignments 79

Glossary 81

Index 85

ix

Introduction

T

he compact, lightweight EPSON

®

ELP-3300 Projector allows you to project

computer images and video onto a large screen for full-color presentations. The

projector can connect simultaneously to two image sources; one can be your PC

or Apple

®

Macintosh

®

computer and the other can be a video source, such as a

VCR, camcorder, digital camera, or laser disk player. Audio can be supplied with

one or both image sources.

Images are displayed in up to 16 million colors at a resolution of 640

x 480

pixels. The projector’s 300-lumen bulb produces bright images that can be easily

seen in rooms light enough to take notes. You can play audio on the projector’s

internal speakers or route it to an external speaker for amplification. You control

the projector through a hand-held remote control, which allows you to switch

between image sources and make adjustments to the projected image.

The projector supports any computer capable of VGA output, including IBM

®

-

compatible PCs and laptops and Apple Macintosh computers, including the

PowerBook

TM

and Power Macintosh.

TM

The video source can be NTSC, PAL,

and SECAM in composite video or S-Video format.

x

Introduction

Getting the Most Out of Your Projector

The projector comes with a full set of features that allow you to control the

settings for the image display, video, and audio. To get the most out of your

projector, read this section for a quick summary of the important features.

Remote control

The buttons on the remote control allow you to directly change the volume,

control the brightness, or switch from one image source to the other. Additional

adjustments can be made by using the buttons on the remote control to access

the projector’s menu system.

The menus, which you can superimpose on the projector image or display on

your computer screen, allow you to do the following:

• Control the brightness, contrast, sharpness, color, and position of the image.

• Adjust the volume, balance, treble, and bass settings.

• Adjust the display by rotating or inverting it.

Additional settings are described in Chapter 3.

You can also use the remote control to control your computer if you install the

Serial Communication Kit.

xi

Getting the Most Out of Your Projector

Serial Communication Kit

The Serial Communication Kit allows your computer and projector to communi-

cate over an RS-232C connection. The kit includes an RS-232C serial cable and

two software utilities: ELP Link and ELP Remote Programmer.

• ELP Link allows you to make adjustments to the projector from your computer.

The same controls that are available on your remote control, including the

ability to access the projector menus, are available from the main ELP Link

screen.

• The ELP Remote Programmer allows you to use the remote control to control

your computer. The trackball moves the mouse on your computer monitor, and

five buttons on the remote control can be programmed to drag or click

windows and icons or perform the same functions as keys on your keyboard.

For information on using ELP Link, see Chapters 2 and 3. For information on the

ELP Remote Programmer, see Chapter 4.

Standby mode

Standby mode conserves electricity by automatically turning off the lamp if the

projector has not been used for a specified period of time (the default is

10 minutes). In standby mode, the projector remains on but the lamp is turned

off. This conserves electricity, cools the projector, and extends the life of the lamp.

Use the Standby button on the remote control to turn standby mode on or off.

xii

Introduction

Rear projection

If you have a translucent screen, you can set up the projector for rear projection,

in which the projector sits behind the screen. To use the remote control with rear

projection, you need to purchase the optional lead wire and connect the remote

control directly to your computer.

Optional Accessories

To enhance your use of the projector, EPSON provides the following accessories:

• Polarized screens designed specifically for use with the projector. They allow

you to project images in a bright, illuminated room, making it unnecessary to

dim lights to view the projected image. The polarized screen comes in two

sizes: 40" and 60" diagonal.

• Carrying cases especially designed for the projector and its cables. Both a soft

and hard case are available.

• Remote control lead wire, which allows you to directly connect the remote

control to the projector. This option enables you to use the remote control

when an object is blocking the path between the remote control and projector,

such as during rear projection when the screen is between the remote control

and the projector.

You can purchase these accessories from your ELP-3300 dealer or by calling

EPSON Accessories at (800) 873-7766.

xiii

About This Manual

Chapter 1, “Installation,” gives step-by-step instructions on setting up the

projector and connecting it to your computer, video source, and optional other

equipment. Read the installation procedures that apply to your environment.

Chapter 2, “Using the Projector,” tells you how to turn on the projector; control

simple projector settings using the remote control, the operation panel, and the

ELP Link software; and set up the projector for rear projection.

Chapter 3, “Using the Menus,” describes how to use the menus to adjust the color

and image settings, change the display of the projected image, and modify audio

settings such as bass or treble.

Chapter 4, “Remote Control of the Computer,” explains how to use the ELP

Remote Programmer so you can use the remote control to control your com-

puter. It also describes how you can assign keyboard macros to the program-

mable buttons on the remote control.

Chapter 5, “Maintenance,” describes how to maintain the projector in good

working order.

Chapter 6, “Troubleshooting,” tells you how to interpret the projector’s status

lights and gives helpful information for avoiding errors, optimizing image quality,

and solving problems.

Appendix A provides technical specifications.

About This Manual

xiv

Introduction

Safety Instructions

Follow these safety instructions when setting up and using the projector:

1. Do not place the projector on an unstable cart, stand, or table.

2. Do not use the projector near water or sources of heat.

3. Use attachments only as recommended.

4. Use the type of power source indicated on the projector. If you are not sure

of the type of power available, consult your dealer or local power company.

5. Insert the projector’s three-wire grounding-type plug into a properly

grounded outlet. If you have a two-prong outlet, contact an electrician to

replace it.

6. Do not overload wall outlets, extension cords, or integral convenience

receptacles. This can cause fire or electric shock.

7. Do not place the projector where the cord can be walked on.

8. Unplug the projector from the wall outlet before cleaning. Use a damp cloth

for cleaning. Do not use liquid or aerosol cleaners.

9. Do not block the slots and openings in the projector case. They provide

ventilation and prevent the projector from overheating. Do not put the

projector on a sofa, rug, or other soft surface or in a built-in installation

unless proper ventilation is provided.

xv

10. Never push objects of any kind through cabinet slots. Never spill liquid of any

kind in the projector.

11. Except as specifically explained in this Owner’s Manual, do not attempt to

service this product yourself. Opening or removing covers may expose you to

dangerous voltages and other hazards. Refer all servicing to qualified service

personnel.

12. Unplug the projector during lightning storms or when it will not be used for

extended periods.

13. Unplug the projector from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into it or it has been exposed to rain or water.

C. If it does not operate normally when the operating instructions are

followed or if it exhibits a distinct change in performance, indicating a

need for service.

D. If it has been dropped or the cabinet has been damaged.

Safety Instructions

xvi

Introduction

Where to Get Help

If you purchased your projector in the United States or Canada, EPSON provides

customer support and service through a network of authorized EPSON Customer

Care Centers. EPSON also provides the following services when you dial

(800) 922-8911:

• EPSON Technical information library fax service

• Product literature on current and new products

• Assistance in locating your nearest Authorized EPSON Reseller or Customer

Care Center

• Technical information on the installation, configuration, and operation of

EPSON products

• Customer relations.

You can purchase supplies, parts, printed manuals, and accessories for EPSON

products by calling EPSON Accessories at (800) 873-7766 (U.S. sales only). In

Canada, call (800) BUY-EPSON for sales locations.

If you purchased your projector outside the United States or Canada, contact your

EPSON dealer or the marketing location nearest you for customer support and

service.

xvii

Electronic support services

If you have a modem, you can access helpful tips, specifiations, drivers, applica-

tion notes, and bulletins for EPSON products through the online services below.

EPSON Download Service

You can call the EPSON Download Service (our BBS) at (310) 782-4531. No

membership is required. Make sure your communications software is set to 8

data bits with 1 stop bit, no parity bit, and a modem speed up to 28.8 Kbps. See

the manual that came with your communications software for more information.

CompuServe

®

online support

CompuServe members can call the Epson America Forum on CompuServe. If you

are already a member, simply type GO EPSON at the menu prompt to reach the

Epson America Forum. If you are not currently a member of CompuServe, you

are eligible for a free introductory membership as an owner of an EPSON

product. This membership entitles you to:

• An introductory credit on CompuServe

• Your own user ID and password

• A complimentary subscription to CompuServe Magazine, CompuServe’s

monthly publication.

Where to Get Help

xviii

Introduction

To take advantage of this offer, call (800) 848-8199 in the United States

and Canada and ask for representative #529. In other countries, call

(614) 529-1611 or your local CompuServe access number.

World Wide Web site

If you are connected to the Internet and have a Web browser, you can access

EPSON's World Wide Web site at http://www.epson.com. EPSON’s home page

links users to What’s New, EPSON Products, EPSON Connection, Corporate Info,

and EPSON Contacts. Link to the EPSON Connection for the latest drivers and

FAQs (Frequently Asked Questions) and the EPSON Chat area. To get in touch

with EPSON around the world, EPSON Contacts includes Contact Information for

local EPSON subsidiaries.

Energy Star Compliance

As an Energy Star Partner, EPSON has determined that this product meets the

Energy Star guidelines for energy efficiency. The EPA estimates that if all desktop

computers, printers, and other peripheral devices met Energy Star standards,

energy cost savings would exceed $1 billion annually and carbon dioxide

emissions would be reduced by 20 million tons.

1

Installation

T

his chapter describes how to unpack, set up, and connect your projector to

other equipment. You must connect the projector to your computer or to a video

source such as a VCR, camcorder, digital camera, or laser disk player. Connecting

to other equipment is optional. For example, you may want to connect the projec-

tor to both your computer and video source, or set up the projector for one or

more of the following:

• Provide audio for one or both image sources. The audio source can be the

computer, video source, or another device such as a stereo.

• Connect to an external speaker or PA system to amplify the audio.

• Install the RS-232C Serial Communication Kit. This kit enables communication

between your computer and the projector so you can use the remote control to

control your computer and use your computer to control the projector settings.

• Directly connect the remote control and the projector using the optional lead

wire. You need to do this to use the remote control for rear projection.

Page is loading ...

Epson ELP-3300, ELP-800UG User manual

Related papers

Other documents