MPN(s): FANBK
SKU(s): 402604
UPC(s): 840009213212
2
KEY
BOX
DESCRIPTION
QTY
KEY
BOX
DESCRIPTION
QTY
(1) 1
Main Frame
1
(50) 1
Seat Slide Rail Sleeve
2
(2) 1
Front Stabilizer
1
(51) 1
Speed Sensor Magnet and Plate
1
(3) 1
Rear Stabilizer
1
(52) 1
Speed Sensor Magnet Seat
1
(4) 1
Console Post
1
(53) 1
Sensor Bracket
1
(5) 1
Seat Post
1
(54) 1
PVC Cable Plug
1
(6) 1
Seat Slide Rail
1
(55) 1
Rubber Grommet
1
(7) 1
Linkage Arm
2
(56) 1
Leveling Foot
4
(8) 1
Left Handlebar
1
(57) 1
Turf Tire
2
(9) 1
Right Handlebar
1
(58) 1
Cell Phone Holder
1
(10) 1
Gray Base Tube (For shipping ONLY)
( NO USE FOR ASSEMBLY)
2
(59) 1
Console 1
(11) 1
Bell Crank
1
(60) 1
Sensor Plug
1
(12) 1
Chain Wheel
1
(61) 1
Console Plug
1
(13) 1
Front Chainguard
1
(62) 1
Rivet Φ15*12
6
(14) 1
Chain Guard 1
(63) 1
6003ZZ Ball Bearing 2
(15) 1
Rear Chainguard
1
(64) 1
6003ZZ Ball Bearing
4
3
KEY BOX DESCRIPTION QTY KEY BOX DESCRIPTION QTY
(16) 1
Big L Bracket for Chainguard
1
(65) 1
6202RS Ball Bearing
2
(17) 1
Fan Wheel Assembly
1
(66) 1
Knuckle Bearing
2
(18) 1
Mid Hub Assembly
1
(67) 1
Self-Tapping Screw 4.8*20
2
(19) 1
Chain Wheel
1
(68) 1
Self-Tapping Screw 4.8*15
3
(20) 1
Right Fan Cage
1
(69) 1
Button Head Screw M5*6
15
(21) 1
Left Fan Cage
1
(70) 1
Button Head Screw M5*30
1
(22) 1
Speed Sensor Plate Clip
3
(71) 1
Button Head Screw M5*10
1
(23) 1
Fan Cage Cover
1
(72) 1
Button Head Screw M5*15
4
(24) 1
Small L Bracket for Chainguard
1
(73) 1
Allen Bolt M6*15
2
(25) 1
Positioning Plate
1
(74) 1
Allen Bolt M6*12
1
(26) 1
Blade
6
(75) 1
Allen Bolt M8*25
2
(27) 1
Big Washer
1
(76) 1
Allen Bolt M10*15 (For shipping ONLY)
4
(28) 1
Foot Peg
2
(77) 1
Allen Bolt M6*25
3
(29) 1
Pedal Shaft
1
(78) 1
Allen Bolt M5*15
2
(30) 1
Turf Tire Axle
1
(79) 1
Allen Bolt M8*45
2
(31) 1
Bearing Sleeve
2
(80) 1
Tubular Rivet M8
2
(32) 1
bushing
2
(81) 1
Allen Bolt M10*35
8
(33) 1
Footrest
2
(82) 1
Clip Φ17
2
(34) 1
Left Crank
1
(83) 1
Clip Φ22
2
(35) 1
Right Crank
1
(84) 1
Clip Φ35*1.2
2
(36) 1
Short Chain
1
(85) 1
Wave Washer Φ17*Φ19*0.5
9
(37) 1
Long Chain
1
(86) 1
Spring Washer Φ8
2
(38) 1
Left Pedal
1
(87) 1
Spring Washer Φ10
4
(39) 1
Right Pedal
1
(88) 1
Flat Washer M5(Φ5.5*Φ10*1)
2
(40) 1
Water Bottle Holder Kit
1
(89) 1
Flat Washer M5(Φ5.5*Φ10*1)
2
(41) 1
Seat Pad
1
(90) 1
Flat Washer Φ9*Φ16*1.6
2
(42) 1
Pop Pin Knob
2
(91) 1
Flat Washer Φ11*Φ20*2
10
(43) 1
PVC tube
6
(92) 1
Big Washer Φ11*Φ34*3
2
(44) 1
PVC Handle Grip
2
(93) 1
Nylon Nut M5
1
(45) 1
PP Wind Shield
1
(94) 1
Nylon Nut M6
3
(46) 1
Plug
1
(95) 1
Thin Nut M8
2
(47) 1
Plug
1
(96) 1
Lock Nut M8
2
(48) 1
End Cap for Crank
4
(97) 1
Thin Nut M10
4
(49) 1
Plug
8
(98) 1
Flange Nut M10*1.25
4
4
STEP 1
A. Remove the four Allen Bolts (76) and two Gray Base Tubes (10) and discard (for shipping protection only)
B. Install the four Leveling Feet (56) on the Front Stabilizer (2) and the Rear Stabilizer (3).
C. Install the Front Stabilizer (2) and the Rear Stabilizer (3) on Main Frame (1), using Allen Bolt M10*35(81),
Spring Washer (87) and Flat Washer (91).
D. Adjust the four Leveling Feet (56) to ensure that the Main Frame (1) is level, then tighten the Thin Nut (97)
firmly to the Front Stabilizer (2) and Rear Stabilizer (3).
5
STEP 2
A. Install the Turf Tire Axle (30) on the Front Stabilizer (2), using the Allen Bolt M10*35(81) and
Flat Washer (91).
B. Install the two Turf Tires (57) on the Turf Tire Axle (30), using Big Washer (92) and Allen Bolt M10*35(81).
C. Insert the Seat Post (5) into the Main Frame (1) and secure using the Pop Pin Knob (42). To properly secure
the pop pin, once the seat is at the desired height, firmly tighten the knob.
D. Insert the Seat Slide Rail (6) into the Seat Post (5), and secure by firmly tightening the Pop Pin Knob (42).
E. Install the Allen Bolt M6*15(73) into the lower back of the Seat Slide Rail (6).
F. Attach the Seat Pad (41) onto the Seat Slide Rail (6), using the Allen Bolt M6*15(73) and Big Washer (27).
G. Adjust the Seat Pad (41) to a horizontal, then firmly tighten the nuts on both side of Seat Pad (41).
6
STEP 3
A. Remove the Rubber Grommet (55), expose the Sensor Plug (60), then reinstall Rubber Grommet (55).
B. Carefully connect the Sensor Plug (60) to the Console Plug (61).
C. Install the Console Post (4) on the Main Frame (1) using Allen Bolt M8*25(75), Spring Washer (86), and Flat
Washer (90). Do not tighten the bolts until the end of Step 4 (D).
D. Attach Water Bottle Holder (40) onto Console Post (4), using Flat Washers (89) and Allen Bolts M5*15(78).
E. Install the Left Handlebar (8) by partially threading the Footrest (33) onto the Main Frame (1). Attach
Linkage Arm (7) to the pre-installed Allen Bolt M8*45 (79) on the lower portion of the Left Handlebar using
the M8 Locking Nut (96). Finish tightening Footrest (33) to Main Frame (1).
F. Install the Right Handlebar (9) by partially threading the Footrest (33) onto the Main Frame. Attach Linkage
Arm (7) to the pre-installed Allen Bolt M8*45 (79) using the M8 Locking Nut (96). Finish tightening Footrest
(33) to Main Frame (1).
7
STEP 4
A. Adjust the handles to a parallel position. Refer to the distance between Left & Right Handlebars (8&9) seen
in the diagram below.
B. Connect the Console Plug (61) with the back of the Console (59).
C. Install the Console (59) onto the Console Post (4), using the Button Head Screw M6*20(72).
D. Adjust the Console Post (4) to ensure it is evenly spaced and square to the Main Frame (1) and tighten the
two Console Post bolts to the Main Frame (1)
E. Install the Left Pedal (38) onto the Left Crank (34), turning the pedal counterclockwise.
F. Install the Right Pedal (39) onto the Right Crank (35), turning the pedal clockwise.
8
This concludes the FANBK Owner’s Manual.
If applicable to your product, make sure to tighten
all nut-and-bolt combinations before use.
Enjoy!
DISCLAIMER
This equipment must be used with care by capable and competent individuals under supervision, if necessary.
The use of any fitness equipment, including this one, involves the potential risk of injury. You accept and assume full
responsibility for any and all injuries, damages (both economic and non-economic), and losses of any type, which may
occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and
agents from any and all claims, demands, damages, rights of action, or causes of action, present or future, whether the
same be known or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
TITAN MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN
USE OF THE EQUIPMENT.
NEED HELP?
CONTACT US FIRST.
1 (800) 605-8241
info@titandistributorsinc.com /
Business Hours: Monday–Friday • 8:00 a.m.–5:00 p.m. (CT)
/
