Craftsman 358.351580 Owner's manual

Brand: Craftsman

Model: 358.351580

Category: Power chainsaws

Type: Owner's manual

This manual is also suitable for

358351580

Operator's Manual

CRRFTSHRN

2.4 cu. in./40cc 2-Cycle _

GASOLINE CHAIN SAW

Model No.

358.351580 - 18 In. Bar

WARNING:- ;

Read and follow all Safety Rules and Operating

Instructionsbefore first use of this product.

For answers to your questions about this product:

Call 7 am-7 pm, Mon.--Sat., or 10 am-7 pm, Sun.

• 1-800-235-5878 (Hours listedare CentraITime)

Sear_r_r__Roebuckand Co., Hoffman Estates, IL60179 USA

530087620 07/21/98

Warranty 2 Storage 16

Safety Rules 2 Trouble ShootingChart 17

Assembly 5 Repair Parts List 21

Operation -_ .... •_ - 6 Spanish 24

Maintenance 11 Parts & Ordering Back

Sewice and Adjustments 14

FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS

CHAIN SAW : i

Forone year from_e date Ofpurchese,when this CraftsmanGas Chain Saw is

maintained, lubdcated and tuned-up accordingto the owner's manual, Sears will

repair,;:free_ofcharge, any defectin material or workmanship.

This warranty dxcludes the bar, chain, spark plugand air filter,which are

expendable parts, and become wom duringnormaluse.

Ifthis Gas Chain Saw is used forcommercial or rentalpurposes,this warranty

appliesfor 30 days from the dateof purchase.

WARRANTY SERVICE iS AVAILABLE BY RETURNING THIS CHAIN SAW TO

THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES.

This warranty gives you specificlegal rights,and you may also have other rights

which vary from state to state.

Sears, Roebuck and Co., D/817 WA, Hoffman Estat_s,;IL 60179

WARNING: Always disconnect spark

plug wire when making repairs except

for carburetor adjustments. Because a

chain saw is a high-speed woodcutting

tool, careless or improper use of this

tool can cause serious injury.

PLAN AHEAD

• Restrict the use of your sew to adult

users who understand and can follow

the safety rules, precautions, and op-

" "_e_atinginstructions found in this

manual.

Hearing A.=_ Safety Hat

Protection_ ___ Eye

Snug i_r,_-- Protection

Fitting _ Heavy Duty

Clothing Gloves

ShoesSafety j Safety Chaps

__ T_Jearprotectivegear. Always use

steel-toed safety footwear withnon-

slipsoles; snug-fittingclothing;heavy-

duty, non-slipgloves;eye protection

such as non-fogging,ventedgoggles

or face screen;an approved safety

hard hat;and sound barriers(ear

plugs ormufflers)to protectyour

hearing. Regular users shouldhave

hearing checked regularlyas chain

saw noisecan damage hearing.Se-

cure hair above shoulderlength.

• Keep all partsof your body away from

the chain when the engineis running.

• Keep children,bystanders,and ani-

mals at least 30 feet (10 meters)

away fromthe work area when start-

ing and usingthe saw.

• Do not handle oroperate a chainsaw

when you are fatigued, ill, or upset, or

ifyou have taken alcohol, drugs,or

medication.You must be in good

physicalconditionand mentally aiert.

Ifyou have any conditionthat might

be aggravated by strenuouswork,

checkwith doctorbefore operating.

° Do notstart cuttinguntilyou have a

clear workarea, securefooting,and

especially if you are felling a tree, a

retreat path.

OPERATE YOUR SAW SAFELY

• Donotoperatewithonehand.Sed-

ousinjurytotheoperator,helpers,or

bystandersmayresult from one-

handed operation.A chain saw is in-

tended for two-handed use.

• Operate the chain sa3vonly in.a wail-

ventilated outdoorarea.

• Do not operate saw from a ladderor

in a tree, unless you are specifically

trained to doso.

• Make sure the chain will not make

contact with any object whilestarting

the engine. Never try to startthe saw

when the guide bar is in a cut.

• Do notput pressure onthe saw, es-

peciallyat the and of the cut. Doing

so san cause you to lose control

when the cut iscompleted.

• Stop engine before setting sew down.

• Hand carry saw only when engine is

stopped. Carry with muffler away from

body;guide bar & chainprojectingbe-

hindyou;guide bar preferablycov-

ered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

• Have all chain saw service performed

by a qualified service dealer except

the items listed in the maintenance

section of this manual.

• Make certain the saw chain stops

moving when the throttle tdgger is re-

leased. For correction, refer to =Car-

buretor Adjustments."

• Keep the handles dry, clean, and free

from oil or fuel mixture.

• Keep caps and fasteners securely

tightened.

• Use only Craftsman accessodes and

replacement parts as recommended.

Nev_e_r_modifyyour saw.

HANDLE FUEL WIT.[-I CAUTION

• Do not smoke while handling fuel or

while operating the saw.

• Eliminme_I sourcasofspsrksortiame

in areas where fuel is mixed or poured.

• Mix and pour fuel in an outdoor area

and use an approved, marked con-

tainer for all fuel purposes. Wipe up

all fuel spills before starting saw.

• Move at least 10 feet (3 meters) from

fueling site before starting.

• Turn the engine off and let sew cool in

a non-combustible area, not on dry

"le,a_e_, straw, paper, etc. Slowly re-

move fuel cap and refuel unit.

• Store the unit and fuel in a cool, dry

well ventilated space where fuel va-

pors cannot reach sparks or open

flames from water heaters, electric

motors or switches, furnaces, etc.

GUARD AGAINST KICKBACK

Follow.all safety rules to help avoid

Idcld0ack and other forces which can

result in sedous injury.

_ _ KickbackPath

AvoidObstructions

ClearThe Worldng Area

WARNING: RotationalKickbackcan

occurwhen the movingchain contacts

an object atthe upper portionof the tip

ofthe guide bar.Contact at the upper

portion ofthe tiP of the guide bar can

cause the chain to dig intothe object,

whichstops the chainforan instant.The

resultisa lightningfast, reverse reaction

which kicksthe guide bar up and back

toward the operator.

Pinch-Kickbeckand Pull-Inoccur when

the chain is suddenly stopped by being

pinched,caught, or by contacting a for-

eign object inthe wood. This sudden

stopping ofthe chain resultsin a rever-

sal of the chain force used to cut wood

and causes the saw to move in the op-

positedirection ofthe chain rotation.

Pinch-Kickbackdrivesthe saw straight

back toward the operator.Pull-In pulls

the saw away from the operator.

REDUCE THE CHANCE OF

KICKBACK

• Recognize that kJdd:_ck can happen.

With a basis understanding of k_k,

you can reduce the element of surprise

which contributes to accidents.

Never let the moving chain contact

any object at the tip of the guide bar.

Keep working area free from obstruc-

tions such as other trees, branches,

rocks, fences, stumps, etc. Eliminate

or avoid any obstruction that your saw

chain could hit while cutting.

• Keep saw chain sharp and propedy

tensioned. A loose or dull chain can

increase the chance of kickback. Fol-

low manufacturer's chain sharpening

and maintenance instructions. Check

tension at regular intervals, but never

with engine running. Make sure bar

clamp nuts are escurely tightened.

• Be(] n and continue cuffing at lull

sp_ed. If the chalh is movin_ at a

slower speed, there is greater chance

of kickback occurring.

• Use extreme caution when reentering

a cut.

Do not attempt cuts startLngwith the

i tip.ofthe cuts).

bar._lunge

Watch for sh=ftinglogs or other forces

thatcould close a cutand pinchor fall

intochain.

• Use the specified Reduced-Kickback

Guide Bar and Low-Kickback Chain.

Avoid Pinch-Kickback:

• Be extremely aware of situationsor

obstructionsthat can cause matenau

to pinch the top of or otherwise stop

the chain.

• Do not cut more than one log at a

time.

• Do not twist saw as bar iswithdrawn

from an undercut when bucking.

Avoid Pull-In:

• Alwaysbegin cuttingwith the engine

at fullspeed and the saw housing

against wood.

• Use wedges made of plastic orwood.

Never use metal to holdthe cut open.

MAINTAIN CONTROL

Stand tothe leftof the saw

Thumb on \_

_ Elbow

locked

Never reversehand _)osit]or)s

• A good, firm grip on the saw with both

hands will he|p you maintain control.

Don t let go. Grip the rear handle with

your dght hand whether you are dght

or left handed. Wrap the fingers of

your left hand over and around the

front handlebar, and your left thumb

under the front handlebar. Keep your

left arm straight with the elbow locked.

• Position your left hand on the front

, handlebar so it is in a straight line with

• _--yeur dght hand on the rear handle

when making bucking cuts. Stand

slightly to the left side of the saw to

keep y.our body from being in a direct

line with-thecuttingchain.

• Stand withyour weight evenly bal-

anced on bothfeet.

• Do notoverreach.You could be drawn

or thrown offbalanceand losecontrol.

• Do notcut above.shoulderheight, itis

difficultto maintaincontrol of saw

above shoulder height.

KICKBACK SAFETY FEATURES

WARNING: The followingfeatures are

includedonyour saw to help reduce

hazard of kickback;however, suchfea-

tures will nottotallyeliminatethis dan-

ger. Do not relyonly onsafety devices.

• Handguard: designed to reduce the

chance of your left hand contacting

the chain ifyour hand slips offthe

front handlebar.

• Positionoffront and rear handlebars:

designed with distance between han-

dles and "in-line"with each other.The

spread and "in-line"position ofthe

hands provided by this design work

together to give balance and resis-

tance in controllingthe pivotof the

saw back toward the operator ifkick-

back occurs.

• Reduced-Kickback Guide Bar: de-

signed with a _;mall radiustipwhich

reduces the size ofthe kickback dan-

ger zone. Thistype bar has been

demonstrated to significantlyreduce

the number and seriousnessof kick-

backs when tested in accordance with

ANSI B175.1.

Smell Radius

Tip Guide Bar

• Low-KickbackChain:has met kickback

performance.mq..uirarnantswhen tested

on a representativesampleof chain

saws below3.8 cubic inch

displacementspecifiedinANSI B175.1.

Low-KickbackChain

ContouredDepthGauge

_._.... Elon_tsd Guard Unk

DeflectsKickback

ForceAndAllows

WoodToGradually

RideIntoCutter

SAFETY NOTICE: Exposure to

vibrationsthroughprolongeduse of

gasoline powered hand toolscould .

cause bloodvessel or nerve oamagelm

the fingers, hands, andjoints ofpeop e

prone to circulation disorders or

abnormal swelling. Prolonged usa in

cold weather has been linked to blood

vessel damage in otherwise healthy

people• if symptoms occur such as

numbness, pain, loss of strength,

change in skin color or _exturs, orJoss

of feeling in the fingers, hands, or joints,

discontinue the use of this tool and

seek medical attention. An

anti-vibration system does not

guarantee the avoidance of these

problems. Users who operate power

tools on a continual and regular basis

must closely monitor their physical

condition and the condition of this tool•

CHAIN BRAKE If this saw is to be used

for commercial logging, you must order

and install a chain brake to comply with

Federal OSHA Regulations for Com-

mercial Logging• Contact your Sears

Service Center or call 1-800-235-5878.

SPARK ARRESTOR: Your saw is

equipped with a temperature limiting

mufflerand sparkarrestingscreen

which meetsthe requirementsof

Califomia Codes4442 and 4443. All

U•S. forest land and the states of

Califomia, Idaho, Maine, Minnesota,

New Jersey,Oregon, and Washington

requirebY lawthat many intemal

combustionengines be equippedwith a

spark arrestorscreen. Ifyou operate a

chain saw in a state or localewhere

such regulationsexist, you are legally

responsiblefor maintainingthe

operating conditionofthese parts.

Failureto doso isa violationof the law.

Refer to Customer Responsibilities

chart inthe MAINTENANCEsection.

STANDARDS: This chain saw is listed

by UnderwritersLaborstodes, Inc.in

accordance withAmerican National

Standards for Gasolins-Powersd Chain

Saws Safety Requirements (ANSI

B175.1-1991).

CARTON CONTENTS

Check carton contents against the fol-

lowing list.

Model: 358.351580

• Chain Saw (fully assembled)

• Chain adjustment tool

• 2-cycle engine oil

• Examine parts for damage. Do not

use damaged parts.

• If you need assistance or find that

parts are missing or damaged, please

call 1-800-235-5878.

NOTE: It is normal to hear the fuel filter

rattle Jnan empty fuel tank.

Your unit has been factory tested and

the carburetor precisely adjusted. As a

result you may smell gasoline or find a

drop of oil/fuel residue on the muffler

when you unpack the unit.

ASSEMBLY

Yoursaw isfullyassembled, and no

assembly isnecessary.

KNOW YOUR SAW

READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERAT-

ING YOUR CHAIN SAW. Compare the illustrationswithyour unitto familiarize

yourselfwith the 10eationof the various controlsand adjustments.Save this

manual forfuture reference.

.... ;_zM__tler_""'_ _ __B_I er

/Starter//

Bar Oil Fill Cap Housing Fuel Mix FillCap

Cylinder Cover

Fast Idle

Rsar

Handle

Adjusting Chain

Screw Direction

ofTravel

Throffie Choke _ Bar Clamp Nuts Guide Bar

Trigger Knob Bar Clamp Chain

Catcher

THROTTLE LOCKOUT

The throttle lockout must be pressed

before you can squeeze the throttle trig-

ge_. This feature prevents you from ac-

cidentally squeezing the trigger.

CHOKE/FAST IDLE LI_VER

The choke and fast idle speed are set

by pulling the choke lever out fully for

cold or for refueled starting. The choke

provides additional fuel when starting a

cold engine.

CHAIN TENSION

It is normalfor a new chainto stretch

duringfirst30 minutesof operation. You

shouldcheck your chaintensionfre-

quently.See Chain Tensionunderthe

Service and Adjustmentssection.

BEFORE STARTING ENGINE

WARNING: Besureto readthefuel

handlinginformationinthesafetyrules

sectionofthismanualbeforeyoubegin.

Ifyoudo notunderstandthefuelhan-

dlinginformationdonotattempttofuel

yourunit.Seekhelpfr0_ someone that

does understandthe informationor call

the customer assistance help lineat

1-800-235-5878.

GUIDE BAR AND CHAIN OIL

The chain oiler provides continuous lu-

brication to the chain and guide bar. Be

sure to fill the bar oil tank when you fill

the fuel tank (Capacity = 6.8 ft. oz.)

For maximum guide bar and chain life,

we recommend you use Craftsman

chain saw bar oil. If Craftsman bar oil is

not available, you may use a good

grade SAE 30 oil until you are able to

obtain Craftsman brand. The oil output

is automatically metered during opera-

tion. Your saw will use approximately

one tank of bar oil for every tank of fuel

mix. Always fill the bar oil tank when

you fill the fuel tank.

FUELING ENGINE

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good

quality 2-cycle air-cooled engine oil. We

recommend Craftsman brand oil. Mix

gasoline and oil at a ratio of 40:1 (A

40:1 ratio is obtained by mixing 3.2

ounces of oil with 1 gallon of unleaded

gasoline). DO NOT USE automotive oil

or boat oil. These oils will cause engine

damage. When mixing fuel follow the

instructions printed on the container.

Once oil is added to the gasoline,

shake container momentarily to assure

that_LIl_ fuel is thoroughly mixed.

Always read and follow the safety rules

relating to fuel before fue.ling your unit.

IMPORTANT

Experience indicates that alcohol

blended fuels (called gasohol or using

ethanol or methanol) can attract mois-

ture which leads to separation and

formation of acids during storage. Acid-

ic gas can damage the fuel system of

an engine while in storage.

To avoid engine problems, the fuel sys-

tem should be emptied before storage

for _)._lays or longer. Drain the gas

tank, start the engine and let it run until

the fuel lines and carburetor are empty.

Use fresh fuel next season. See STOR-

AGE instructions for additional informa-

tion.

Never use engine or carburetor cleaner

products in the fuel tank or permanent

damage may occur.

See the STORAGE section for additional

information..

STOPPING YOUR ENGINE

• Move On/Stop switch to the STOP

position.

• If engine does not stop, pull choke

knob out fully.

STARTING YOUR ENGINE

COLD ENGINE OR WARM ENGINE

AFTER RUNNING OUT OF FUEL

• Fuel engine following instructions un-

der FUELING ENGINE.

• Fill bar oil tank with bar oil. Your saw

will use approximately one tank of bar

oil for each tank of fuel mix.

• Move On/Stop switch to ON position.

• Pull choke knob out fully.

° Prime engine by slowly pressing prim-

er bulb six times.

ON/STOP

Switch

PrimerBulb

• Set saw onthe ground.Gripfront

handlewith your left hand and place

rightfootthrough rear handle.

Choke knob

NOTE: When pulling the starter rope,

do not use the full extent of the rope.

Do not let starter rope snap back.

Hold handle. Let rope rewind slowly.

• Sharply pull starter rope handle 5

times with your right hand. The en-

gine may sound as if it is trying to

start before the 5th pull; if so, proceed

to the next step.

• Fullypush-inchokeleverandcontin-

uetopullstarterropehandleuntilen-

ginestarts.

• Then, squeeze and release the

throttle trigger to retum engine to idle

speed.

• To stop engine, move _Q+_Stop switch

to the STOP position.

Starter Rope Handle

Righi_:FootThrough Rear Handle

STARTING A WARM ENGINE

DO NOT use the choke to start a warm

engine or flooding and hard starting

mayoccur,

• Move On/Stop switch to ON.

• Slowly press primer bulb 6 times.

• Set the chain saw on the ground. Grip

the front handle with your left hand

and place your right foot through the

opening in the rear handle.

• Pull choke lever out fully, then push it

in fully to set engine in fast idle posi-

ton.

• Sharply pull starter rope handle with

your right hand until the engine starts,

but no more than 5 times.

• Then, squeeze and release the

throttle triggsr to retum engine to idle

speed.

• To stop engine, move On/Stop switch

to the STOP position.

'I_I=FICULT STARTING OR

STARTING A FLOODED ENGINE

The engine may be flooded if it has not

started after 10 pulls. Flooded engines

can be cleared of excess fuel with the

following procedure:

• Pull choke lever out fully, then push it

in fully to set engine in fast idle posi-

ton.

• Verify that the On/Stop switch is in the

ON position.

• With saw on ground, grip front handle

with left hand and place right foot

__through rear handle.

• Grip starter rope handle and pull rope

firmly and quickly to start engine. If

not successful,repeat untilengine

starts.

Startingcould requiremany pullsde-

pendingon how badlyunitisflooded. If

engine stillfails to start,refer toTROU-

BLESHOOTING chart orcall

1-800-235-5878.

OPERATING TIPS

• Check chain tensionbefore first use

and after 1 minute of operation.See

Chain Tensioninthe Maintenance

section.

• Cut woodonly.Do notcut metal, plas-

tics, masonry,non-woodbuildingma-

terials, etc.

• Stop the saw ifthe chain strikes a for-

eign object. Inspectthe saw and re-

pair parts as necessary.

• Keep the chain out of dirtand sand.

Even a smallamount of dirtwillquick-

lydull a chain and increasethe possi-

bilityof kickback.

• Practice cuttinga few smalllogs using

the followingsteps. This willhelp you

get the =feel" of usingyoursaw before

you begin a majorsawing operation.

• Squeeze the throttletriggerand al-

low the engine to reach full speed

beforecutting.

• Begin cuttingwiththe saw frame

against the log.

• Keep the engine at full speed the

entiretime you are cutting.

• Allowthe chain to cutfor you. Exert

only lightdownward pressure.

• Release the throttletrigger assoon

as the cut iscompleted, allowingthe

engine to idle. Ifyou runthe saw at

fullthrottlewithouta cuttingload,

unnecessarywear can occur.

• Toavoid losingcontrolwhen cut is

complete, do not putpressure on

saw at end of cut.

• Stop the enginebefore settingthe

saw down.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead

branches which can fall while cutting

causing serious injury. Do not cut near

buildings or electrical wires if you do not

know the direction of tree fall, nor cut at

night since you will not be able to see

well, nor during bad weather such as

rain, snow, or strong winds, etc.

Carefully plan your sawing operation in

advance. Clear the work area. You

need a clear area all around the tree so

you can have secure footing. Study the

naturalconditionsthatcancausethe

tree to fall in a particular direction, such

conditions include:

• The wind direction and speed.

• The lean of the tree. The lean of a

tree might not be apparent due to un-

even or sloping terraiB. Use a plumb

or level to determine the direction of

tree lean.

• Weight and branches on one side.

• Surrounding trees and obstacles.

Look for decay and rot. If the trunk is

rotted, it can snap and fall toward the

operator.

Make sure there is enough room for the

tree to fall. Maintain a distance of 2-1/2

tree lengths from the nearest person or

other objects. Engine noise can drown

out a warning call.

Remove dirt, stones, loose bark, nails,

staples, and wire from the tree where

cuts are to be made.

Plan a clear retreat path

.... ( ]--,,,=-_- Directionof Fall

FELLING LARGE TREES

(6 inches indiameter or larger)

The notchmethod isused to fell large

trees. A notchis cut on the side ofthe

tree in the desired directionof fall. After

a fellingcut ismade on the opposite

side of tree, the tree should fall in the

directionofthe notch.

NOTE: If the tree has large buttress

roots,_move them before making the

notch.

NOTCH CUT AND FELt.ING TREE

• Make notch cut by cutting the top of

the notch first. Cut through 1/3 of the

diameter of the tree. Next complete

the notch by cutting the bottom. See

illustration. Once the notch is cut re-

move the wedge of wood from the

tree.

• After removing the wood, make the

felling cut on the opposite side of the

notch. This is done by making a cut

abouttwo inches higher than the can-

ter..e._the notch. This will leave

enough uncut wood between the fell-

ing cut and the notch to form a hinge.

This hingewill help preventthe tree

fromfalling inthe wrongdirection.

Rrst cut | Rnal cuthere

Notch,_ _'.': r

Hinge holdstree on stumpand helps

controlfell

Opening

oftelling

Closingof

notch

NOTE: Before felling cut is complete,

use wedges to open the cut when

necessary to control the direction of fall.

To avoid kickback and chain damage,

use wood or'plastic wedges, but never

steel or iron wedges.

• Be alert of signs that the tree is ready

to fall: cracking sounds, widening of

the felling cut, or movement in the up-

per branches.

• As tree starts to fall, stop sew, put it

down, and get away quickly on your

planned retreat path.

• Be extremely cautious with partially

fallen trees that may be poody sup-

ported. When a tree doesn't fall com-

pletely, set the saw aside and pull

down the tree with a cable winch,

block and tackle, or tractor. Do not

use your saw to cut down a partially

fallen tree.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a

fallen tree to the desired log size.

WARNING: Do not stand on the log

being cut. Any portion can roll causing

loss of footing and control. Do not stand

downhill of the log being cut.

IMPORTANT POINTS

• Cut only one log at a time.

• CUt shattered wood very carefully;

sharp pieces of wood could be flung

toward operator.

• Use a sawhorse to cut small logs.

Never allow another person to hold

the log while cutting and never hold

the log with your leg or foot.

• Do not cut in an area where logs,

limbs, and roots are tangled. Drag the

logs into a clear _,rea before cutting

them.

BUCKING TECHNIQUES

WARNING: If saw becomes pinched

or hung ina log, don't try to force itout.

You can losecontrol ofthe saw result-

ing in injuryand/or damage to the saw.

Stop the saw, ddve a wedge ofplastic

or wood intothe cut untilthe saw can

be removed easily. Restart the saw and

carefullyreenterthe cut. Do not use a

metal wedge. Do not attempt to restart

your saw when it ispinched or hungin

a log.

Use a wedge to remove pinchedsaw

_. Turn saw OFF and

A_.'_ use aplasticorwooden

toforce cutopen.

Overcutting begins on the top side of

the log with the bottom of the saw

against the log. When overcutting use

light downward pressure.

Overcutting Undercutting

Undercutting involves cutting on the

underside of the log with top of saw

. a_galnstthe log. When undemutting use

light upward pressure. Hold saw firmly

and maintain control. "l:'hesaw will tend

to push back toward you:

WARNING: Never tum saw upside

down to undercuL The saw cannot be

controlled in this position.

Always make your first cut on the pres-

sure side of the log.

Rrst cuton pressure side of log

Rrst cut on pressureside of log

BUCKING WITHOUT A SUPPORT

• Ovemut through 1/3ofthe diameter of

the log.

• Rollthe log over and finishwitha sec-

ondovercut.

• Watch for logswitha pressureside.

See illustrationabove for cuttinglogs

with a pressureside.

Using s log nd

for support 2 Cut,_k

-- 1stcut

stCut

2ndCut

BUCKING USING A LOG OR

SUPPORT STAND

• Remember your first cut is always on

the pressure side of the log.

(Refer to the illustration below for your

first and second cut)

• Your first cut should extend 1/3 of the

diameter of the log.

• Finish with your second cut.

Using s su_ Cut

1stCut

LIMBING AND PRUNING

WARNING: Neverclimbintoatreeto

limborprune.Donotstandonladders,

platforms,alog,orinanyposition

whichcancauseyouto loseyourbal-

anceorcontrolofthesaw.

IMPORTANTPOINTS_ .....

• Watch out for springpoles.

Springpolesare small size limbs

whichcan whip toward you, or pull

with the 1/3,2/3 cuttingtechniques de-

scdbed inthe buckingsection.

• Always usa an overcut to cutsmall

and freely hanginglimbs.Undercut-

tingcould cause limbstofall and

pinchthe saw.

PRUNING

WARNING: Limitpruningto limbs

shoulderheight or below. Do not cut if

branches are higher thanyour shoul-

you off balance. Use extreme caution der. Get a professional to do the job.

when cutting small size limbs. • Make your first cut 1/3 of the way

• Be alert for springback. Watch out for through the bottom of the limb.

branches that are bent or under pres- • Next make a second cut all the way

sure. Avoid being struck by the

branch or the saw when the tension in •

the wood fibers is released.

• Frequently clear branches out of the

way to avoid tdpping on them.

LIMBING

• Limb a tree only after it is cut down.

• Leave the larger limbs underneath the

felled tree to support the tree as you

work.

• Start at the base of the felled tree and

work toward the top, cutting branches'

and limbs. Remove small limbs with

one cut.

• Keep the tree between you and the

chain.

• Remove larger, supporting branches

through the limb.

Finish the pruning operation by using

an overcut so that the stump of the

limb protrudes 1 to 2 inches from the

trunk of the tree.

Secondcut

Firstcut

1/3 ofway

3rd cut 1 to2 in.

CUSTOMER RESPONSIBILITIES

Fill in dates as you complete

regular service

Check for damaged/worn parts

Check for loose fasteners/parts

Chi_l_ chain tension

Check chain sharpness :

Check guide bar

Clean unit & labels

Clean air filter

Clean/inspect spark arrestor

screen & inspect muffler

Replace spark plug

Every

25 hrs

Service

Dates

GENERAL RECOMMENDATIONS

The warranty onthis unitdoes notcov-

er itemsthat have been subjected to

operatorabuse or negligence. To re-

ceivefullvalue from the warranty,the

operatormust maintain unitas instruct-

ed inthis manual. _arious adjustments

willneedto be made periodically to

properlymaintain your unit.

• Once a year, replace the spark plug,

air filterelement, and check guide bar

and chainfor wear. A new spark plug

and airfilter element assures proper

air-fuel mixture and helpsyour engine

runbetter and last longer.

WARNING: Disconnectthe spark plug

before performing maintenance except

forcarburetor adjustments.

LUBRICATION

II _

1 Bar 2 Bar Oil

Sprocket FillCap _

Lube . _ f

1 Sprocket lube

2 Craftsman chain saw bar oil

CHECK FOR DAMAGED OR

WORN PARTS

Replacement of damaged/wom parts

shouldbe referred toyour Sears Ser-

vice Center.

NOTE: It is normalfor a small amount

of oilto appear under the saw after en-

gine stops. Do notconfuse thiswith a

leakingoiltank.

• On/Stop Switch - Ensure On/Stop

switchfunctions properly by moving

. the switchto the "Stop"position.

" "Make sureengine stops;then restart

engine and continue.

• FuelTank- Discontidueuse ofchain

saw iffuel tank shows signs ofdam-

age orleaks.

• Oil Tank- Discontinueuse of chain

saw ifoiltank shows signsof damage

or leaks.

CHECK FOR LOOSE

FASTENERS AND PARTS

• Bar Clamp Nuts

• Chain

• Muffler

-, .._Cylinder Shield

• Air Filter

• Clutch Drum/Sprocket

• Handle Screws

• VibrationMounts

• Starter Housing

• Handguard

CHECK CHAIN TENSION

• Use the screwdriverend of the bar

toolto move chainaround guide bar

to ensure kinks do not exist.The

chainshould rotatefreely.

BarClampNuts

• Loosen bar clamp nuts untilthey are

fingertight againstthe bar clamp.

• Turn adjustingscrew untilchain bare-

ly touchesthe bottom of guidebar.

_ _'_r_n_

• Using bartool,rollchainaroundguide

bar toensureall linksare in bargroove.

• Lift uptip ofguide bar to check for

sag. Release tip of guide bar,then

rum adjustingscrew untilsag does

notexist.

• While liftingtip ofguide bar, tighten

bar clamp nuts withthe bar tool.

Torque to 10-15 ft-lbs.

• Use the screwdriver end of the bar

tool to move chain around guide bar.

• If chain does not rotate, it is too tight.

Slightly loosen bar clamp nuts and

loosen chain by turning the adjusting

screw. Retightan bar clamp nuts.

• If chain is too loose, it will sag below

the guide bar. DO NOT operate the

saw if the chain is loose.

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A

dull chain makes a sawdust powder

and cuts slowly.

CHAINSHARPENING

Chainsharpeningrequiresspecial

tools.Youcanpurchasesharpening

toolsatSearsor gotoa professional

chainsharpener.

CHECK GUIDE BAR_ .......

Conditions which require guide bar

maintenance:

• Saw cuts to one side or at an angle.

• Saw has to be forced through the cut.

• Inadequate supply of oil to the bar

and chain.

Check the condition of the guide bar

each time the chain is sharpened. A

wom guide bar will damage the chain

and make cuffing difficult. To maintain

guide bar:.

• Move On/Stop switch to =Stop."

• Remove bar and chain from saw.

• Clean all sawdust and any other

debris from the guide bar groove and

sprocket hole after each use.

Remove Sawdust From Guide

Bar Groov_

• Add lubricant to sprocket hole after

each use.

• Burring of guide bar rails is a normal

process of rail wear. Remove these

burrs with a fiat file.

• When rail top is uneven, use a fiat file

to restore square edges and sides.

FileEdges and

sidesSquare

Worn G-roove Correct Groove

Replace the guide bar w_hen.the groove

is wom, the guide bar is berit or

cracked, or when excess- heating or

burring of the rails occurs• If replace-

ment is necessary, use only the guide

bar specif'md for your saw in the repair

pads list, also specified on the replace-

ment bar and chain decal located on

the chain saw.

CLEAN UNIT & LABELS

• Clean'the unit using a damp cloth with

a mild detergent.

• Wipe off the unit with a clean dry

cloth.

CLEAN AIR FILTER

A dirty air filter decreases the life and

performance of the engine and in-

creases fuel consumption and harmful

emissions. Always clean your air filter

after 15 tanks of fuel or 5 hours of op-

eration, whichever comes first. Clean

more frequently in dusty conditions. It is

advisable to replace your air filter with a

new one after every 50 hours of opera-

tion, or annually, whichever comes firsL

To clean filter:.

• Loosen 3 screws on cylinder cover.

• Remove cylinder cover.

• Remove air filter.

• Clean the air filter using hot soapy

water. Rinse with clean cool water.

Air dry completely before remstalhng.

• Lightly oil air filter before installing.

Use 2-cycle engine oil or motor oil

(SAE 30). Squeeze excess oil from

filter."

the air filter.

• Reinstall air filter•

• Reinstall cylinder cover and 3 screws

(15-20 in-lbs.).

AirFilter Cover

Screws

INSPECT MUFFLER AND SPARK • Replaceany broken or cracked muf-

ARRESTOR SCREEN

As the unit is used, carbon deposits

build up on the muffler and spark

arrestor screen, and must be removed

to avoid creating a fire hazard or affect-

ing engine performance. ....

Replace the spark arrestor screen if

breaks occur.

Muffler Diffuser

Muffler

Cover

Screws

Body Muffler

Cover

CLEANING THE SPARK

ARRESTOR SCREEN

Cleaning is requiredevew 25 hoursof

operationor annually,whichever comes

first.

• Loosenand remove the 2 mufflercov- Screws

er screws.

• Remove the mufflercover (cover

snaps offmuffler body). Plug

• Remove mufflerdiffuserand spark Boot

arrestorscreen assembly. Noticethe

orientationofthese pads for reassem-

bling.

• Clean the spark arrestorscreen with a Spark

wire brush. Replace screen if breaks Plug

are found.

fler parts.

• Reinstall diffuser and spark arrestor

screen assembly with holes facing up

and towards muffler cover.

• Reinstall muffler cover and 2 screws

(-/-8 ft-lbs.).

REPLACE SPARK PLUG

The spark plugshouldbe replaced

each year to ensure the engine starts

easier and runsbetter. Ignitiontiming is

fixedand nonadjustable.

• Loosenthe 3 screws onthe cylinder

cover.

• Remove the cylinder cover.

• Pulloffthe spark plugboot.

• Remove spark plugfrom cylinderand

discard.

• Replace with Champion CJ7Y spark

plugand tightenwith a 3/4inch socket

wrench (10-12 ft-lbs). Spark pluggap

shouldbe .025 in.

• Reinstallthe spark plugboot.

• Reinstallthe cylindercover and 3

screws (15-20 in-lbs).

Cylinder

.CH_AIN REPLACEMENT

CAUTION: Wear protective gloves

when handling chain. "l_hechain is

sharp and can cut you even when it is

not moving.

It is normal for a new chain to stretch dur-

ing the first 15 minutes of oparation. You

should recheck your chain tension fre-

quenify and adjust the chain tension as

required. See Chain Tension section.

• Move On/Stop switch to the Stop

position.

• Replace the old chain when it be-

comes worn or damaged.

" --_U_e only the Low-Kickback replace-

ment chain specified in the repair

parts list. The correct replacement bar

and chain is also specified on a decal

located onthe chainsaw.

• See your Sears Service Center to re-

place and sharpen individualcutters

on yourchain.

• Remove bar clamp nuts.

• Remove bar clamp.

• Remove the old chain.

Bar

Clamp

Bar

Clamp Nuts

•Tum adjusting screw on bar to move

the tensioning rack as far as it will go

toward the front of the bar.

(_'-0 _ .-

Tensioning Rack /

• Slide the guide bar rearward until it

stops against the sprocket.

• Carefully remove new chain from

package. Hold chain with the drive

links as shown.

Cutters Dep_ Gauge

Drive Links

• Place chain over and behind clutch.

• Fit the bottom of the drive links be-

tween the teeth in the sprocket nose.

• Fit chain drive links into bar groove.

• Pull guide bar forward until the chain

is snug in the guide bar groove.

• Install the bar clamp.

• Install bar clamp nuts; finger tighten

only. Do not tighten any further at this

point.

Bar Clamp Nuts

CHAIN ADJUSTMENT

See "Chain Tension" in Maintenance

section.

CLEAN FUEL FILTER

To clean fuel filter, drain your unit by

running dry of fuel, remove fuel cap/re-

tainer assembly from tank. Pull filter

from tank end remove from line. Clean

with mild detergent and rinse. Dry thor-

oughly, reassemble.

CARB-BRETOR ADJUSTMENT

WARNING: Thechainwillbe moving

during most of this procedure. Wear

yourprotsctiveequipment and observe

all safety precautions.Dudng the low

speed mixtureadjustment recheck idle

speed after each turn ofthe screw. The

chain must notmove at idlespeed.

Carburetoradjustmentiscdticaland if

done impropedycan permanently dam-

age the engine as well as the carbure-

tor. If you require furtherassistance or

are unsureabout performing this proce-

dure, call ourcustomerassistancehelp

lineat 1-800-235-5878.

Old fuel, a dirtyair filter,dirtyfuel filter,

or floodingmay give the impressionof

an improperlyadjustedcarburetor.

Check these conditionsbefore adjust-

Ing the carburetor.

The carburetorhas been carefully set at

the factory. Adjustmentsmay be neces-

sary ifyou noticeany ofthe following

conditions:

• Chain moves at idle.See =IdleSpeed"

under adjustingprocedure.

• Saw will not idle. See =IdleSpeed"

and "Low Speed Mixture'under ad-

justing procedure.

• Engine die._or hesitateswhen it

shouldaccelerate. See =Acceleration

ChecW'under adjustingprocedure.

• Loseofcuttingpower.See =High

Speed Mixture H" under adjusting

procedure.

There are three adjustment screws on

the carburetor.They are labeled H, L,

and T. They are locatedin the area just

above the pdmer bulb.

CARBURETOR PRESETS

When making adjustments,

the plasticlimitercaps beyond the

stops or damage will occur.

Ifcarburetor presets are notneeded,

proceed to "IdleAdjustments."

• Turnboth mixture screws counter-

clockwiseuntilthey stop.

• Turnthe idlespeed screw clockwise

untilit stops.Now turncountemlock-

wise 4-1/2turns.

Start motor,let it run for3 minutes,and

proceed to the adjustmentsection. If

engine does notstart, referto trouble-

shootingchart orcall 1-800-235-5878.

If engineperformance isacceptable at

the preset positionsand there is no

chain movement at idle, nofurtherad-

justment is necessary.

ADJUSTING PROCEDURE

Idle Speed "T"

Allowenginetoidle.Adjustspeeduntil

enginerunswithoutchainmovementor

stalling.

•Tum clockwise to increase engine

speed if engine stalls or dies.

° Tum counterclockwise to decrease

speed. _ ......

No furtheradjustmentsare necessary if

chain does not move atidlespeed and

ifperformance issatisfactory.

Low Speed Mixture "L"

Allow engine to idle. Then accelerate

the engine and note performance. If en-

gine hesitates, bogs down, or smokes

during acceleration, turn mixture screw

clockwise in 1/16-turn increments until

performance is satisfactory. Repeat this

procedure as necessary for proper ad-

justment. After completing adjustments,

check for acceleration and chain move-

ment at idle. Reset if necessary.

High Speed Mixture "H"

DO NOT operate engine at full throttle

for prolonged pedods while making ad-

justments. Damage to the enginecan

occur. Make a test cut. Based on per-

formance ofthe sew while cutting,ad-

just the highspeed mixturesetting in

1/16-turnincrementsas follows:

• Clockwise untilthe sew has good

power inthe cutwith no hesitation.

Do not adjustby sound or speed, but

judge by how well the saw performs in

the cut.

• Counterclockwiseif the saw has

speed, but diesin the cut or lacks

powerin the cut.

After completingadjustments, checkfor

accelerationand chain movement at

idle. Resetif necessary.

Acceleration Check

Ifthe enginedies or hesitates insteadof

accelerating,tum the low speed mixture

adjustmentcountemlock'wise untilyou

have smoothaccelerationwith no chain

movement at idle. Recheck and adjust

as necessary for acceptable perfor-

mance.

Prepare your unitfor storage at the end

ofthe season or if itwill not be used for

30 days or more.

WARNING:

• Allowthe engineto cool, and secure

the unitbefore stodng ortransporting.

• Store chain saw and fuel in a well

ventilated area where fuel vapors

cannot reach sparks or open flames

fromwater heaters, electric motors or

switches,fumacas, etc.

• Store chain sew with all guards in

place and positionchainsaw so that

-.anysharp objectcannot accidentally

cause injury.

• Store chainsaw well.outof the reach

ofchildren.

EXTERNAL SURFACES

If your chain sew is to be stored for a

period of time, clean it thoroughly be-

fore storage. Store in a clean dry area.

• Lightly oil external metal surfaces and

guide bar.

• Oil the chain and wrap it in heavy pa-

per or cloth.

' -FUEL SYSTEM

Under Fueling Engine in the Operating

Section of this manual, see message

labeled IMPORTANTregardingthe use

of gasoholin your chainsaw.

Fuel stabilizerisan acceptable alterna-

tive in minimizingthe formation offuel

gumdepositsduringstorage. Add stabi-

lizer to thegasoline inthefuel tank or

fuel storagecontainer.Followthe mix

instructionsfound on stabilizer contain-

ers. Run engineat least 5 minutesafter

adding stabilizer.

CRAFTSMAN 40:1, 2-cycle engine oil

(air cooled)is especiallyblended with

fuel stabilizer. Ifyou do not use this

Sears oil,you can add a fuel stabilizer

to your fuel tank.

INTERNAL ENGINE

• Remove spark plug and pour I tea-

spoon of 40:1, 2-cycle engine oil (air

cooled) through the spark plug open-

ing. Slowly pull the starter rope 8 to

10 times to distribute oil.

• Replace spark plug with new one of

recommended type and heat range.

• Clean air filter.

• Check entire unit for loose screws,

nuts, and bolts. Replace any dam-

aged, broken, or worn parts.

• At the beginning of the next season,

use only fresh fuel having the proper

gasoline to oil ratio.

OTHER • Replace your gasoline can if it starts

• Do not store gasoline from one sea- to rust..

son to another.

TROUBLESHOOTING CHART

TROUBLE CAUSE REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

Enginewillnot

idleproperly.

• Ignitionswitchoff.

• Engine flooded.

• Fuel tank empty.

• Spark plugnotfiring.

• Fuel not reaching

carburetor.

Engine will not

accelerate,

lacks power,

or dies under

a load.

• Carburetor requires

adjustmenL

• None of the above.

• Idle speed set too high

or too low.

• Low Speed Mixture

requires adjustment.

• Crankshaft seals worn.

• Compression low.

• None of the above.

• Air filter dirty.

• Spark plug fouled.

• Carburetor requires

adjustment.

• Exhaust portsormuf-

fler outletsplugged.

• Compression low.

• None of the above.

Enginesmokes •

excessively. •

• Move Ignition switch to ON.

• See "Starting Instructions."

• Fill tank with correct fuel mixture,

• Install new spark plug.

• Check for dirty fuel filter;, replace

Check for kinked or split fuel line;

repair or replace.

• See •Carburetor Adjustments."

• Contact Sears Service.

• See "CarburetorAdjustments."

• See =Carburetor Adjustments. •

• Contact Sears Service.

• Clean or replace air filter.

• Clean or replace plug

and regap.

• See "Carburetor Adjustments?

• Contact Sears Service.

Choke pa[tiallyon. •

Fuel mixtureincorrect. •

• Airfilter dirty.

• High Speed Mixture •

requiresadjustment.

• Crankcase leak. •

Adjustchoke.

Empty fuel tank and refillwith

correctfuel mixture.

Clean orreplace airfilter.

See "CarburetorAdjustments."

Contact Sears Service.

TROUBLE SHOOTING CHART - Continued

TROUBLE

Engine runs

hot.

Oilinadequate

for bar and

chain

lubrication.

Chain moves

at idle speed.

Chain does

not move

i when engine

Is accelerated.

Chain clatters

or cuts roughly,

Chain stops

within the cut.

Chain cuts at

an angle.

CAUSE

• Fuel mixture incorrect.

_, Spark plug incorrect.

o4 High spe-ed Mixture

set too lean.

• Exhaust ports or muf-

fler outlets plugged.

• Carbon build-up on

muffler outlet screen.

• Fan housing/cylinder

fins dirty.

• None of the above.

• Oil tank empty.

• Oil pump or oil filter

clogged.

• Guide bar oil hole

blocked.

• Idle speed requires

adjustment.

• Clutch requires repair.

• Chain tension too

tight.

• Carburetor requires

adjustment.

• Guide bar rails

pinched.

• Clutch slipping.

• Chain tension incorrect.

• Cutters damaged.

• Chain wom.

• Cutters dull, improperly

sharpened, or depth

gauges too high.

• Sprocket worn.

• Chain installed

backwards.

• Chain cuttertops not

- fil_d flat.

• Guide bar burred or

bent; rails uneven.

• Clutch slipping

• Cutters damaged on

one side.

• Chain dull on one side.

• Guide bar bent or wom.

REMEDY

• See "Fueling Your Unit."

• Replace with correct plug.

• See "Carburetor Adjustments."

• Contact Sears Service.

• Clean spark arrestor screen.

• Clean area.

• Contact Sears Service.

• Fill oil tank.

• Contact Sears Service.

• Remove bar and clean.

• See "Carburetor Adjustments."

• Contact Sears Service.

• See "Chain Tension."

• See!_Carburetor Adjustments."

• Repair or replace.

• Contact Sears Service.

• See =Chain Tension."

• Contact Sears Service.

• Resharpen or replace chain.

• See "Sharpening Chain."

• Contact Sears Service.

• Install chainin fightdirection.

• See "Sharpening Chain."

• Repair or replace guide bar.

• Contact Sears Service.

• See "Sharpening Chain."

• Replace guide bar.

If situations occur which are not covered in this manual, use cars and good

judgement. If you need assistance, contact Sears Service or the CUSTOMER

, __=SISTANCE HELPLINE at 1-800-235-5878.

U. S. EPA/CALIFORNIA parts not made or approved by the origi-

naJequipment manutacturer.

EMISSION CONTROL You are responsible for presenting your

WARRANTY STATEMENT lawn and garden equipment engine to a

SEARS authorized repair center as soon

as a problem exists. Warranty repairs

YOUR WARRANTY, RIGHTS AND snould be completed in a reasonable

OBLIGATIONS amount' of time, not to exceed 30 days.

The U. S. Environmental Protection

Agency/Califomia Air Resources Board

and SEARS, ROEBUCK AND CO., USA

are pleased to explain the emissions

control system warranty on your lawn

ano garden equipment engine. All new

utility and lawn and garden equipment

engines must be designed, built, and

equipped to meet the stringent anti-

Ifyou have anyquestions re_lard!ng your

warranty rightsand responsJbditias,you

should contact your nearest authorized

service center or call SEARS at

1-800-473-7247.

WARRANTY COMMENCEMENT

DATE - -

The warranty period beginson the date

the lawnand garden equipmentengineis

smog standards. SEARS must warrant purchased.

the emissioncontrolsystem onyourlawn LENGTH OF COVERAGE --

and garden ec.].uipmentengine forthe pe- Thiswarranty shallhe fora pedodoftwo

riodsoftime listedbelow providedthere yearsfrom the initialdate of purchase.

hasbeen noabuse, neglect, orimproper

maintenance of your lawn and garden WHAT IS COVERED --

equipment engine. REPAIR OR REPLACEMENT

Your emission control system includes

parts such as the carburetor and the igni-

tion system.

Where a warrantable condition exits,

SEARS will repair your lawn and garden

equipment engine at no cost to you. Ex-

penses covered under warranty include

diagnosis, parts and labor.

MANUFACTURER'S WARRANTY

COVERAGE - -

Ifany emissionsrelated part onyour en-

gine (as listed under Emissions Control

Warranty Parts List) isdefective ora de-

fect in the materials or workmanship of

the engine causes the failure of suchan

emissionrelatedpart, the part willbe re-

paired or replacedby SEARS.

OWNER SWARRANTY RESPON-

SIBILITIES --

As the-lawn and garden equipment en-

gine owner, you are responsible for the

performance of the required mainte-

nance listed in your Owner's Manual.

SEARS recommends that you retain all

receipts covering maintenance on your

lawn and garden equipment engine, but

SEARS cannot deny warranty solely for

the lack of receipts or foryour failure to

ensure the performance of all scheduled

maintenance.

OF PARTS--

Repair or replacement of anywarranted

partwillbe performedat nocharge tothe

owner at an approved SEARS servicing

center. .,

Ifyouhave anyquestionsr

warranty rightsand

should contact your nearest

service center or call SEARS at

1-800-473-7247.

WARRANTY PERIOD --

Any warranted part which is not sched-

uled for replacement, uired mainte-

nance, or which i.'

ular inspection to the effect of

replace as necessary" shall be war-

ranted for 2 years. Any

warranted part which is scheduled for re-

placement as required maintenance

shall be warranted for thepenod

of time up to the first scheduled replace-

ment point for that part.

DIAGNOSIS - -

The owner shall not be charged for diag-

nostic labor which leads to the deter-

mination that a warranted part

is defective if the diagnostic work is per-

rormed at an approved SEARS servicing

center.

As the lawn and garden equipment en- CONSEQUENTIAL DAMAGES - -

gine owner, you should be aware that SEARS may beliablefordamagestooth-

SEARS may deny you warranty cover- eren_linecomponentscausedbythefail-

age if your lawn and garden equipment ure ot awarranted partstill undarwar-

en_jit'te=0Ta part of it has failed due to ranty.

abuse, neglect, improper maintenance,

unapproved modifications, or the use of WHAT IS NOT COVERED -

Allfailurescausedbyabuse,neglect,or MAINTENANCE, REPLACEMENT

impropermaintenance are notcovered. AND REPAIR OF EMISSION RE-

ADD-ON OR MODIRED PARTS -- LATED PARTS - -

The use of add-on or mod_d partscan

be grounds for disallowing a warranty

claim.SEARS

isnotliabletocovePfailures0f-warranted

partscaused bythe useofadd-on ormo-

difiedparts.

HOW TO FILE A CLAIM - -

Ifyouhave any questions regardingyour

warranty rights and responsibilities,you

should contact your nearest authorized

service center or call SEARS at

1-800-473-7247.

WHERE TO GET WARRANTY

SERVICE - -

Any SEARS approved replacement part

usedinthe performance ofanywarranty

maintenance or repair on emission re-

lated parts will be provided without

charge to the owner ifthe part is under

warranty.

EMISSION CONTROL WARRAN-

TY PARTS LIST--

1. Carburetor

2. IgnitionSystem

a. Spark Plug, covered upto

maintenanceschedule.

b. IgnitionModule

MAINTENANCE STATEMENT--

Warrantyservicesor repairsshallbe pro- The owner is responsiblefor the perfor-

vided at all SEARS at 1-800-473-7247 mance of all required maintenance as

servicecenters, definedin the owner's manual.

Page is loading ...

Craftsman 358.351580 Owner's manual

Brand: Craftsman

Model: 358.351580

Category: Power chainsaws

Type: Owner's manual

This manual is also suitable for

358351580

Download PDF

report

Craftsman 358.351580 Owner's manual

This manual is also suitable for

Craftsman 358.351580 Owner's manual

Related papers

Other documents