OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
7 in. TILE SAW
SCIE À CARREAUX
DE 178 mm (7 po)
SIERRA DE LOSAS
DE 178 mm (7 pulg.)
WS722
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe
leer y comprender el manual del
operador antes de usar este producto.
AVERTISSEMENT :
Pour réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
TABLE OF CONTENTS
General Safety Rules .......................2-3
Specific Safety Rules .........................3
Symbols ..............................................4
Electrical ..........................................5-6
Features ..............................................6
Assembly .........................................7-8
Operation .......................................8-10
Maintenance ..................................... 11
Figures (Illustrations) ...................12-15
Parts Ordering
and Service .........................Back page
TABLE DES MATIÈRES
Règles de sécurité générales ..........2-3
Règles de sécurité particulières .........3
Symboles ............................................4
Caractéristiques électriques ............5-6
Caractéristiques .................................6
Assemblage .....................................7-8
Utilisation .......................................8-10
Entretien ...........................................11
Figures (illustrations) ....................12-15
Commande de pièces
et dépannage ....................Page arrière
ÍNDICE DE CONTENIDO
Reglas de seguridad generales .......2-3
Reglas de seguridad específicas ....3-4
Símbolos ............................................4
Aspectos eléctricos .........................5-6
Características ...................................6
Armado ............................................7-8
Funcionamiento .............................8-10
Mantenimiento ..................................11
Figuras (illustraciones) .................12-15
Pedidos de piezas
y servicio ....................... Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
2 — English
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator’s
manual carefully. Learn the saw’s applications and
limitations as well as the specific potential hazards related
to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY PREVENT-
ING BODY CONTACT WITH GROUNDED SURFACES.
For example, pipes, radiators, ranges, refrigerator enclo-
sures.
KEEP GUARDS IN PLACE and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and benches
invite accidents. DO NOT leave tools or pieces of wood
on the saw while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visi-
tors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. Use only a cord heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 16 is recommended for an extension
cord 50 feet or less in length. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
(rubber soled boots) are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work
when practical, it is safer than using your hand and frees
both hands to operate the tool.
DON’T OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow instruc-
tions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, wheels, bits,
cutters, etc., all tools should be disconnected.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a wheel or cutter against the direction of rotation of wheel
or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord away from heat, oil, and sharp
edges.
ALWAYS USE AN OUTDOOR EXTENSION CORD
MARKED “W-A” OR “W”. These cords are rated for
outdoor use and reduce the risk of electric shock.
ALWAYS KEEP THE SPLASH HOOD IN PLACE and in
working order.
3 — English
GENERAL SAFETY RULES
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from wheels. Do not reach underneathwork
or around or over the wheel while wheel is rotating. Do not
attempt to remove cut material when wheel is moving.
WHEEL COASTS AFTER BEING TURNED OFF.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If dam-
aged, have repaired by a qualified service technician at
an authorized service facility. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating wheel.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electri-
cal receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
USE ONLY CORRECT WHEELS. Do not use wheels with
incorrect size holes. Never use washers or arbor nuts that
are defective or incorrect. The maximum wheel capacity
of your saw is 7 in. (178 mm).
BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
NEVER TOUCH WHEEL or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING COM-
PONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
DOUBLE CHECK ALL SET-UPS. Make sure wheel is tight
and not making contact with saw or workpiece before
connecting to power supply.
ALWAYS SECURE WORKPIECE firmly against the rip
guide, miter guide, or bevel table.
NEVER stand or have any part of your body in line with
the path of the wheel.
NEVER attempt to free a stalled wheel without first turning
the saw OFF and disconnecting the saw from the power
source.
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
saw.
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use splash hood for every operation for which it can
be used.
c) Disconnect saw before servicing, when changing
cutting wheels, and cleaning.
d) Use tool only with smooth edge cutting wheels free
of openings, grooves, and teeth.
e) Replace damaged cutting wheel before operating.
f) Do not fill water bath above water fill line.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions too.
SPECIFIC SAFETY RULES
4 — English
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand opera-
tor’s manual before using this product.
Eye, Ear, & Breathing
Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1 along with hearing and breathing protection.
Wet Conditions Alert Do not expose to rain or use in damp locations.
No Hands Symbol
Failure to keep your hands away from the wheel will result in
serious personal injury.
Electrocution Failure to properly ground can result in electrocution.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
5 — English
ELECTRICAL
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 V, AC
only (normal household current), 60 Hz. Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If the
saw does not operate when plugged into an outlet, double
check the power supply.
SPEED AND WIRING
The no-load speed of this tool is approximately 3,450 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor’s horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
See Figure 1, page 12.
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
tool is equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordi-
nances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING:
Improper installation of the grounding plug is able to
result in a risk of electric shock. When repair or
replacement of the cord is required, do not connect the
grounding wire to either flat blade terminal. The wire with
insulation having an outer surface that is green with or
without yellow stripes is the grounding wire.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 volt circuit and
has a grounding plug similar to the plug illustrated in
Figure 1, page 12. Only connect the product to an outlet
having the same configuration as the plug. Do not use an
adapter with this product.
Ground Fault Circuit Interrupter (GFCI) protection should be
provided on the circuit(s) or outlet(s) to be used for the tile
saw. Outlets are available having built-in GFCI protection
and may be used for this measure of safety.
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool’s plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter’s Laboratories (UL) should be used.
**Ampere rating (on tool data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
Always use an extension cord that is designed for outside
use. This is indicated by the letters “W-A” or “W” on the
cord’s jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
Use only extension cords that are intended for outdoor use.
These extension cords are identified by a marking “Accept-
able for use with outdoor appliances; store indoors while not
in use”. Use only extension cords having an electrical rating
not less than the rating of the product. Do not use damaged
extension cords. Examine extension cord before using and
replace if damaged. Do not abuse extension cords and do
not yank on any cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect the extension
cord from the receptacle before disconnecting the product
from the extension cord.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
6 — English
operator should arrange a “drip loop” in the cord connecting
the saw to the outlet. The “drip loop” is that part of the cord
below the level of the outlet, or the connector if an extension
cord is used, to prevent water traveling along the cord and
coming in contact with the outlet.
If the plug or outlet does get wet, DO NOT unplug the cord.
Disconnect the fuse or circuit breaker that supplies power
to the tool then unplug and examine for the presence of
water in the outlet.
WARNING:
To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch the plug with wet
hands.
ELECTRICAL
If the saw is used with an extension cord, ensure the connec-
tion of the tool’s power cord and the extension cord are not
on the ground. Auxiliary devices should always be plugged
into the wall outlet and not at the connection of an extension
cord and the power tools’ power cord.
If a protected outlet is not available, do not use the saw
until an outlet can be changed or auxiliary protection can
be obtained. These auxiliary protection devices are available
at your local retailer.
POSITION OF THE TILE SAW
See Figure 2, page 12.
To avoid the possibility of the tool plug or outlet getting
wet, position tile saw to one side of a wall-mounted outlet
to prevent water from dripping onto the outlet or plug. The
PRODUCT SPECIFICATIONS
Wheel Diameter ............................................................7 in.
Wheel Arbor .............................................................. 5/8 in.
Rip Capacity (tile size) ................................................20 in.
Diagonal Capacity (tile size) .......................................13 in.
Maximum Depth of Cut .........................................1-1/4 in.
Rating ..........................................120 V~, 60 Hz, 4.8 Amps
No Load Speed .....................................3,450 r/min. (RPM)
FEATURES
KNOW YOUR TILE SAW
See Figure 3, page 12.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
7 in. CUTTING WHEEL - A 7 in. tile cutting wheel is
included with your saw.
WARNING:
Do not use wheels rated less than the speed of this tool.
Failure to heed this warning could result in personal injury.
BEVEL TABLE - Beveled 22.5° and 45° cuts can be made
using the bevel table.
HANDLES - Saw has convenient handles located on left
and right side for lifting and carrying.
MITER GUIDE - The miter guide is fully adjustable for di-
agonal cuts and miter cuts.
MOTOR - This machine has a strong motor with sufficient
power to handle tough cutting jobs.
ON/OFF SWITCH - This saw has an easy access power
switch located below the front rail. To lock the switch in the
OFF position, remove the switch key from the switch. Place
the key in a location that is inaccessible to children and oth-
ers not qualified to use the tool.
RIP GUIDE - Rip guide is fully adjustable for making cross
cuts and using the miter guide.
SPLASH HOOD - The splash hood provides protection
from overspray and mist.
7 — English
UNPACKING
See Figure 3, page 12.
This product requires assembly.
Carefully lift the saw from the carton and place on a level
work surface.
WARNING:
Do not use this product if any parts on the Loose Parts List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
influenced the settings, refer to specific procedures
explained in this manual.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Tile saw
Hex wrench
Arbor wrench
Loose parts
Operator’s Manual
LOOSE PARTS LIST
7 in. cutting wheel
Inner wheel washer
Outer wheel washer
Arbor nut
Bevel table
Splash hood with knob and hex bolt
Splash hood bracket
Overflow drain
Rip guide
Miter guide
WARNING:
If any parts are damaged or missing do not operate this
tool until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
ASSEMBLY
WARNING:
Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration
or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
INSTALLING THE TILE CUTTING WHEEL
See Figure 4, page 13.
WARNING:
A 7 in. tile cutting wheel is the maximum wheel capacity of
the saw. Never use a wheel that is too thick to allow wheel
washer to engage with the flats on the spindle. Larger
wheels will come in contact with the splash hood, while
thicker wheels will prevent the wheel bolt from securing
the wheel on the spindle. Either of these situations
could result in a serious accident and can cause serious
personal injury.
Remove bevel table.
Slide inner wheel washer onto arbor, with small diameter
side flush against the motor.
WARNING:
Always install the inner wheel washer before placing
wheel on arbor. Failure to do so could cause an accident
since the wheel will not tighten properly. Never use
wheels that have openings, grooves, or teeth on this tool.
Place the cutting wheel onto arbor and over sleeve on
inner washer, slide flat against inner washer.
NOTE: Be sure the arrows on the cutting wheel are going
in the counterclockwise direction.
Place outer wheel washer onto arbor and larger diameter
flush against the cutting wheel. The double “D” flats on
the wheel washers align with the flats on the arbor.
Install arbor nut onto arbor. Using wheel wrench and arbor
wrench, tighten arbor nut securely.
To remove tile cutting wheel:
Remove bevel table.
Slide the hex wrench over the wheel arbor nut. Using
other hand, slide arbor wrench onto wheel arbor.
Hold arbor wrench firmly to prevent the wheel from mov-
ing. Turn arbor nut counterclockwise to loosen.
Remove arbor nut, outer wheel washer, and cutting wheel.
8 — English
INSTALLING THE SPLASH HOOD
See Figures 5 - 6, page 13.
Install the L-shaped splash hood bracket into the lip
located under the table behind the wheel.
Install the screws into table and through splash hood
bracket then tighten securely.
NOTE: Be sure that hood bracket is aligned with cutting
wheel so that it does not interfere with material being
cut.
Align splash hood with wheel and slide over bracket. Line
up through holes in splash hood with slot in splash hood
bracket.
NOTE: Always adjust splash hood horizontally to table
and slightly above tile thickness. Hood should not be
touching tile.
Install hex bolt through hood and bracket. Thread splash
hood knob onto bolt and tighten at desired height.
INSTALLING THE OVERFLOW DRAIN
See Figure 7, page 14.
Locate hole on bottom of water fill reservoir.
Firmly push and twist overflow drain into hole.
FILLING THE WATER RESERVOIR
See Figure 8, page 14.
Fill water reservoir with clean tap water to fill line.
NOTE: Overflow drain prevents overfilling.
Replace or close bevel table.
ASSEMBLY
To change reservoir water:
Unplug tile saw.
Remove or open bevel table.
Remove overflow drain and empty into a bucket, do not
allow water to splash onto ground or around machine.
Discard waste water in accordance with local regulations.
Refill with clean tap water.
Replace bevel or close table.
INSTALLING THE RIP GUIDE
See Figures 9 - 10, page 14.
Hook the back of the rip guide onto the back rim of the
saw table.
Lift locking lever and lower front of the rip guide to the
front of the saw table.
Adjust the rip guide to the desired position using the rip
guide scales, located on front and rear of table, to set rip
guide to desired width of cut.
Push the locking lever down to secure to the saw table.
When securely locked, the locking lever should point
downward.
INSTALLING THE MITER GUIDE
See Figure 11, page 14.
Slide miter guide onto rip guide.
Adjust to desired angle using angle scale and tighten
securely with miter guide knob.
With rip guide at desired width, secure in place.
OPERATION
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Straight line cutting operations such as cross cutting,
mitering, ripping, and beveling
NOTE: This saw is designed to cut man-made tile, pavers,
natural stone products, and stone tile products only.
9 — English
OPERATION
MAKING CUTS
Always draw the line to be cut on the tile using a marker or
grease pencil. If the tile is shiny and hard-to-mark, place
masking tape on the tile and mark the tape.
A common problem when cutting tile is straying from the
marked line. Once you’ve strayed from the mark, you can not
force the wheel back to the line by twisting the tile. Instead,
back up and recut the tile slicing off a small amount of tile
until the wheel is back on track.
To avoid this problem, use the rip guide when making cross
cuts, the miter guide for miter cuts and the adjustable right
side table for making bevel cuts, whenever possible.
TO MAKE A CROSS CUT
See Figure 14, page 14.
Cross cuts are straight cuts. The material is fed into the cut
at a 90° angle to the wheel.
Using a marker or grease pencil, mark the area to be cut
on material.
Set the rip guide to desired width, and secure in place.
Place the material on the table and firmly against the rip
guide.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the rip guide and feed
the material into the cutting wheel.
When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE A 45° DIAGONAL CUT
See Figure 15, page 15.
45° Diagonal cuts are also referred to as “long point to long
point cuts”.
Using a marker or grease pencil, mark the area to be cut
on material.
Slide miter guide onto rip guide.
Adjust miter guide to
45°
using angle scale and tighten
securely with knob.
With rip guide at desired width, secure in place.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
ON/OFF SWITCH
See Figure 12, page 14.
Your saw is equipped with an on/off switch that has a built-in
locking feature. This feature is intended to prevent unauthor-
ized and possible hazardous use by children and others.
TO TURN YOUR SAW ON:
With the switch key inserted into the switch, lift the switch
key to turn ON.
TO TURN YOUR SAW OFF:
Press the switch key down to turn OFF.
TO LOCK YOUR SAW:
With the saw turned OFF, pull the switch key from the
switch and store in a safe, secure location.
WARNING:
In the event of a power failure or when the tool is not in
use, turn the switch OFF and remove the switch key.
This action will prevent the tool from accidentally starting
when power returns.
WARNING:
ALWAYS make sure your workpiece is not in contact
with the cutting wheel before operating the switch to
start the tool. Failure to heed this warning may cause the
workpiece to be kicked back toward the operator and
result in serious personal injury.
WARNING:
To reduce the risk of accidental starting, Always make
sure the switch is in the OFF position before plugging
tool into the power source.
USING THE RIP GUIDE AND MITER GUIDE
See Figure 13, page 14.
The rip guide can be used from both the left and right side
of the cutting wheel.
Lift locking lever on rip guide to loosen.
Adjust the rip guide in the desired position using the rip
guide scale, located on front and rear of table, to set rip
guide to desired width of cut.
Push locking lever down to tighten securely.
To adjust angles:
Slide miter guide onto rip guide.
Adjust to desired angle using angle scale and tighten
securely with miter guide knob.
With rip guide at desired width, secure in place.
10 — English
OPERATION
Hold the material firmly against the miter guide and slide
miter guide along rip guide. Feed the material into the
cutting wheel.
When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE A MITER CUT
See Figure 16, page 15.
Miter cuts are used for cutting outside and inside corners
on material, decorative chair rail, and base molding with the
material at any angle to the wheel other than 90°. Miter cuts
tend to “creep” during cutting. This can be controlled by
holding the workpiece securely against the miter guide.
Using a marker or grease pencil, mark the area to be cut
on material.
Slide miter guide onto rip guide.
Adjust miter guide to desired angle
,
using angle scale,
and tighten securely with knob.
With rip guide at desired width, secure in place.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the miter guide and slide
miter guide along rip guide. Feed the material into the
cutting wheel.
When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE AN L-CUT
See Figure 17, page 15.
L-cuts are cuts that remove a piece of tile to fit in a corner,
around a cabinet, or a piece of molding and are made by
two separate cuts.
NOTE: Only overcut on the bottom or underneath side of
the material being cut.
Using a marker or grease pencil, mark the area to be cut
on material.
Cut material to desired width using directions for cross
cut
Set the rip guide to desired width, and secure in place.
Place the material on the table and firmly against the rip
guide.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the rip guide and feed
the material into the cutting wheel.
Make the cut far enough into the material without over-
cutting.
Turn the on/off switch to the OFF position.
Turn the material over and make the cut along one of the
marks. This time overcut the other line and the cut piece
should separate from the rest of the material.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE A BEVEL CUT
See Figures 18 - 19, page 15.
Beveled 22.5° and 45° cuts can be made using the bevel
table.
Using a marker or grease pencil, mark the area to be cut
on material.
Tip up the bevel table.
On underside of bevel table, pull down the two table legs
into right angles of the plate.
Use first notches in legs to rest plate into 22.5° angle.
Use second set of notches to angle bevel table into high-
est 45° angle.
NOTE: Make sure bevel table is set firmly in place before
beginning cut
Fold legs up and lay bevel table flat for 0° angle.
Turn the on/off switch to the ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the bevel table and feed
the material into the cutting wheel.
When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before removing
any part of the material.
NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 12 AFTER
FRENCH AND SPANISH LANGUAGE SECTIONS.
11 — English
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions.
TILE CUTTING WHEEL
For maximum performance and safety, it is recommended
that you use the 7 in. cutting wheel provided with your
saw. Additional cutting wheels of the same high quality are
available at your local dealer.
WARNING:
Do not use cutting wheels rated less than the no load
speed of this tool. Failure to heed this warning could
result in personal injury. Do not use wheel with cracks,
gaps, or teeth.
MAINTENANCE
WARNING:
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
This product has a Three-year Limited Warranty.
For Warranty details go to www.ryobitools.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
13
A - Splash hood (capot anti-éclaboussures, capucha contra salpicaduras)
B - Splash hood bracket (support du capot anti-éclaboussures, soporte de
la capucha contra salpicaduras)
C - Hex bolt (boulon hex, perno hexagonal)
D - Splash hood knob (bouton du capot anti éclaboussures, perilla de la
capucha contra salpicaduras)
A
D
C
B
Fig. 4
Fig. 5
Fig. 6
A - Cutting wheel (meule de coupe, muela para cortar )
B - Screws (vis, tornillos)
C - Lip (lèvre, reborde)
D - Splash hood bracket (support du capot anti-éclaboussures, soporte de
la capucha contra salpicaduras)
A
D
C
B
A - Arbor (arbre, árbol)
B - Cutting wheel (meule de coupe, muela para cortar)
C - Inner wheel washer (rondelle de meule intérieure, arandela interior de
la muela)
D - Sleeve (sleeve, sleeve)
E - Outer wheel washer (rondelle de meule extérieure, arandela exterior de
la muela)
F - Arbor nut (écrou d’arbre, tuerca del árbol)
A
F
C
B
E
A
B
Fig. 7
A - Overflow drain (tuyau de trop-plein, drenaje para derrames)
Fig. 8
D
Page is loading ...
15
Fig. 17
L-CUT (COUPE D’ONGLET, CORTE A INGLETE)
Fig. 15
DIAGONAL CUT (COUPE EN DIAGONALE,
CORTE DIAGONALE)
Fig. 16
MITER CUT (COUPE D’ONGLET, CORTE A INGLETE)
Fig. 18
A
B
C
A - Bevel table (table de biseau, mesa para biselar)
B - Bevel table legs (pattes de la table de biseau, patas de la mesa
para biselar)
C - 22.5º bevel notch (22,5º encoches de biseau, 22,5º muescas
de para biselar)
D - 45º bevel notch (45º encoches de biseau , 45º muescas de
para biselar)
D
BEVEL CUT (COUPE EN BISEAU,CORTE EN BISEL)
Fig. 19
990000859
1-30-14 (REV:01)
OPERATOR’S MANUAL
MANUEL D’UTILISATION / MANUAL DEL OPERADOR
7 in. TILE SAW
SCIE À CARREAUX DE 178 mm (7 po)
SIERRA DE LOSAS
DE 178 mm (7 pulg.)
WS722
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-800-525-2579
États-Unis, Téléphone 1-800-525-2579 • USA, Teléfono 1-800-525-2579
www.ryobitools.com
A subsidiary of Techtronic Industries Co., LTD OTC: TTNDY
RYOBI is a registered trademark of Ryobi Limited and is used pursuant to a license granted by Ryobi Limited.
RYOBI est une marque déposée de Ryobi Limited et est utilisée en vertu d’une licence accordée par Ryobi Limited.
RYOBI es una marca registrada de Ryobi Limited y se utiliza conforme a una licencia otorgada por Ryobi Limited.
To request service, purchase replacement parts,
locate an Authorized Service Center and obtain Customer or Technical Support:
Visit www.ryobitools.com or call 1-800-525-2579
If any parts or accessories are damaged or missing,
do not return this product to the store. Call 1-800-525-2579 for immediate service.
Please obtain your model and serial number from the product data plate.
MODEL NUMBER _______________ SERIAL NUMBER ____________________________
Pour faire une demande de réparations ou obtenir des pièces de rechange, trouver un
Centre de réparations agréé pour obtenir un soutien technique ou le Service à la clientèle :
Visiter www.ryobitools.com ou en téléphonant au 1-800-525-2579
Si des pièces ou accessoires sont manquantes ou endommagées, ne pas retourner
ce produit au magasin. Appeler immédiatement au 1-800-525-2579 pour obtenir de l’aide.
Inscrire les numéros de modèle et de série inscrits sur la plaque d’identification du produit.
NUMÉRO DE MODÈLE _______________ NUMÉRO DE SÉRIE ____________________________
Para obtener servicio, comprar piezas de repuesto, localizar un centro de servicio autorizado
y obtener Servicio o Asistencia Técnica al Consumidor:
Visite www.ryobitools.com o llame al 1-800-525-2579
Si hay alguna pieza ou accesorios dañada o faltante, no devuelva este producto a la tienda.
Llame al 1-800-525-2579 para servicio técnico inmediato.
Obtenga su modelo y número de serie de la placa de datos del producto.
NÚMERO DE MODELO _______________ NÚMERO DE SERIE ____________________________
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Ryobi WS721 Manuel utilisateur
- español: Ryobi WS721 Manual de usuario
