Weider XE-A101 User manual

INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS

BEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES

XE

-A101

MODEL

MODELL

MODELE

MODELO

ELECTRONIC CASH REGISTER

ELEKTRONISCHE REGISTRIERKASSE

CAISSE ENREGISTREUSE ELECTRONIQUE

CAJA REGISTRADORA ELECTRONICA

CAUTION:

The cash register should be securely fitted to the supporting platforms to avoid instability

when the drawer is open.

CAUTION:

The socket-outlet shall be installed near the equipment and shall be easily accessible.

VORSICHT:

Die Netzsteckdose muß nahe dem Gerät angebracht und leicht zugänglich sein.

ATTENTION:

La prise de courant murale devra être installée a proximité de l’équipement et devra être

facilement accessible.

AVISO:

El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.

VARNING:

Det matande vägguttaget skall placeras nära apparaten och vara lätt atkomligt.

CAUTION:

For a complete electrical disconnection pull out the mains plug.

VORSICHT:

Zur vollständigen elektrischen Trennung vom Netz den Netzstecker ziehen.

ATTENTION:

Pour obtenir une mise hors-circuit totale, débrancher la prise de courant secteur.

AVISO:

Para una desconexión eléctrica completa, desenchufar el enchufe de tomacorriente.

VARNING:

För att helt koppla fran strömmen, dra ut stickproppen.

1

English

XE-A101

ELECTRONIC CASH REGISTER

Thank you for purchasing the SHARP Electronic Cash Register Model XE-A101. Please

read this manual carefully before operating your machine. Keep this manual for future

reference. It will help you solve operational problems that you may encounter.

Handling Cautions

• Be very careful for the manual cutter mounted on the printer cover when removing and

replacing the cover, so as not to hurt yourself.

• Install the cash register in a location not subject to direct sunlight, unusual temperature

changes, high humidity, or splashing water.

• Never operate the cash register with wet hands. Water can cause internal component

failure.

• The cash register plugs into any standard wall outlet (official (nominal) voltage). Other

electrical devices on the same electrical circuit can cause the cash register to

malfunction.

• Clean the cash register with a dry, soft cloth. Never use volatile liquids, such as benzine

or thinner. Chemicals can discolor or damage the cabinet.

• For protection against data loss, please purchase three R6 or LR6 batteries (“AA”size),

and install them after resetting you cash register and before using it.

When handling the batteries, never fail to observe the followings. Incorrectly using

batteries can cause them to burst or leaks, possibly damaging the interior of the cash

register.

• Be sure that the positive (+) and negative (-) poles of each battery are facing in the

proper direction for the installation.

• Never mix batteries of different types for the installation.

• Never mix old batteries and new ones for the installation.

• Never leave dead batteries in the battery compartment.

• Remove the batteries if you do not plan to use the cash register for long periods.

• Should a battery leak, clean out the battery compartment immediately, taking care to

avoid letting the battery fluid come into direct contact with your skin.

• For battery disposal, follow the corresponding law in your country.

• For a complete electrical disconnection, pull out the main plug.

IMPORTANT!

Before using the cash register for the first time, you must first reset the cash register, and

then install three new R6 or LR6 batteries (“AA”size) on the register. Never fail to follow

the procedures described on “Before Operation” section.

When you open the carton, make sure that all accessories shown on the “Specifications”

section are contained.

2

Contents

Parts and their Functions..................................................................3

Before Operation ................................................................................4

Reset the Cash Register .......................................................................4

Install Batteries......................................................................................4

Install the Paper Roll .............................................................................5

Set Time and Date.................................................................................6

Check the Time and Date......................................................................6

Program Necessary Items.....................................................................6

When an Error Occurs .......................................................................7

Basic Sales Entry Operation .............................................................8

Before Sales Entries..............................................................................8

Basic Sales Entry ..................................................................................8

Other Features for Sales Entries ......................................................9

VAT (Tax) Calculation ............................................................................9

Discounts and Premiums Using the Percent Key ...............................10

Currency Exchange.............................................................................10

No Sale................................................................................................11

Refund..................................................................................................11

Non-add Code Number........................................................................11

Received-on Account and Paid-out Entries.........................................11

Corrections...........................................................................................11

Reading and Resetting of Sales......................................................12

EURO Migration Function................................................................14

Programming ....................................................................................16

Preparations for Programming ............................................................16

Tax Programming.................................................................................16

Department Programming ...................................................................16

PLU Programming...............................................................................17

Percent Key Programming ..................................................................18

Exchange Key Programming...............................................................18

Printing Format Programming .............................................................18

Miscellaneous Programming ...............................................................19

Consecutive Receipt Number Programming.......................................19

EURO Programming............................................................................20

Rounding Programming (For Australian tax system)...........................20

Secret Code Programming..................................................................20

Checking the Programmed Machine Settings...............................21

Maintenance......................................................................................22

Drawer Handling..................................................................................22

Replacing the Paper Roll.....................................................................22

Replacing the Batteries .......................................................................23

Replacing the Ink Roller ......................................................................23

In Case of Power Failure or Paper Jam..............................................23

Before Calling for Service....................................................................24

Specifications.......................................................................................24

3

Parts and their Functions

Mode Switch

Keyboard

Display

Your cash register is equipped with a front LED (Light-Emitting Diode) display that affords easy

visibility of 9 digits for the operator during transaction.

o: Paper feed key

c: Clear key

V: Value added tax/Received-on

account key

x: Multiplication/Time display key

p: Paid-out key

%: Percent key

v: Void key

e: Escape key

s: Department shift key

P: PLU key

R: Credit key

E: Exchange key

S: Non-add code/Subtotal key

C: Cheque key

t: Total/Amount tender/No sale

key

: Turns the display off. No operations are

possible.

REG: Permits transaction entry.

: Permits correction after finalizing a transaction.

X/F: Permits printing of sales reports and displaying

the flash reports.

Z/PGM: Permits printing and resetting of sales reports

and programming.

Slide the switch to get an appropriate mode.

REG

X/F

Z/PGM

Numeric keys Department key

In order to enter the

departments 5 to 8, press

s and then ! to $.

Repeat: Indicates the number of times the same department key or

PLU key is pressed repeatedly. If an entry is repeated

more than ten times, only the last digit is displayed.

PLU code: Indicates the PLU code entered.

Departments: Indicates the department entered. For example,

if department 1 was pressed, “1” would appear.

4

Parts and their Functions

In order for your cash register to operate properly, you must reset it before programming for the

first time. Follow this procedure.

1. Remove the register from its packing carton.

2. Set the mode switch to the REG position.

3. Insert the plug into the AC outlet. A buzzer will sound three times.

IMPORTANT: This operation must be performed without batteries loaded.

4. The register display should now show “ 0.00”.

5. Press x to confirm the clock starts from “ 0-00”.

6. Press c to cancel the time display.

Symbols and figures appearing on the display:

Error: Appears with an alarm sound when an error is made. If this occurs during a

transaction because of an extra digit entry, simply press c and re-enter correctly.

Program: Appears when the cash register is being programmed in the “Z/PGM” mode.

Finalization: Appears when a transaction is finalized by pressing t, R or C.

Subtotal: Appears when the cash register computes a subtotal when S is pressed, and

also when an amount tendered is less than the total sales amount.

Change: Appears whenever a change due amount is displayed.

Exchange: Appears when E is pressed to calculate a subtotal in foreign currency.

Low battery:Appears when the voltage of the installed batteries is under the required level. You

need to replace the batteries with new ones very soon.

No battery: Appears when the batteries are not installed, or the installed batteries are dead.

You must immediately replace the batteries with new ones.

In addition, the following appear when appropriate:

• The minus sign (-) can appear in positions 2 to 9.

• The decimal point appears in positions 1 to 3.

Please do the following before using the register for the first time.

Three new R6 or LR6 batteries (“AA”size) must be installed in the cash register to prevent the data

and user-programmed settings from being erased from the memory, when the AC cord is

accidentally disconnected or in case of power failure. Once installed, the batteries will last

approximately one year before needing replacement. At this time, the “ ” symbol will appear on

the display to indicate that the batteries are low and that you must replace them within two days.

Install three new R6 or LR6 batteries (“AA”size) according to the procedure shown below with the

AC cord connected and set the mode switch to the REG position:

Step 1 Reset the Cash Register

Step 2 Install Batteries

Before Operation

5

Before Operation

On your register, a printer is mounted, and you can print receipts or journals. For the printer, you

must install the paper roll provided with the register, even when you program the register for not

printing receipt.

1. Push the paper roll release lever in the arrow direction and install the

paper roll on the paper roll holder correctly as shown on the sketch.

Be very careful for the paper direction.

2. Insert the paper straight into the paper inlet, and press o. The

inserted end appears at the printing area.

3. (For journal printing) Insert the top end of the paper into the

slit in the spool shaft and wind the paper two or three turns.

4. (For journal printing) Place the take-up spool on the

bearing.

5. Replace the printer cover. For receipt printing, pass the paper end through the openings of

the printer cover. Be very careful not to cut yourself by the manual cutter.

Step 3 Install the Paper Roll

1. Push the printer cover forward and detach it.

2. Open the battery cover next to the paper roll cradle.

3. Insert three new R6 or LR6 batteries (“AA”size).

4. Confirm the no battery symbol “ ” lights off.

5. Close the battery cover.

Be sure to observe precautions shown on page 1 when

handling batteries.

(Views from rear)

6

Before Operation

Before you can proceed with registration of sales, you must first program necessary items

depending on your needs, such as tax (VAT) system and tax rate, EURO settings, Australian

rounding, decimal point position for currency, though basically your cash register is

pre-programmed so that you can use it with minimum setup.

• Also for merchandise classifications, your register provides categories of departments and PLU

(price lookup). To the departments (totally 8 departments), group attributes such as taxable

status are applied on items when they are entered. PLUs are used to call up preset prices by a

code entry. Every PLU has a code from 1 to 80, and should belong to a department and obtain

attributes of the department. Your cash register is pre-programmed as follows:

Department:Plus department, VAT 1 or TAX 1 - Yes, price entry digit limit - 7 digits

PLU: To use PLU, you must enter preset unit price and the associated department.

• To prevent the cash register from being operated by other person, you can set a secret code. If

set, the secret code must be entered whenever the mode switch is set to the or Z/PGM

position and when a daily Z report is to be issued.

• In your register, a printer is mounted for receipt or journal printing. You can program various

options for printing, and also you can program not to print receipts or journals in the REG mode

(receipt ON/OFF function).

Read through the sales operations section first to understand what you can do on the cash register,

then program the necessary items as necessary.

Step 6. Program Necessary Items

You can display the time and date to check if they are correctly set.

1. Set the mode switch to the REG position.

2. Press x once to display the time.

3. Press x twice to display the date.

4. Press c key to cancel the time/date display.

Step 5 Check the Time and Date

1. Set the mode switch to the Z/PGM position.

2. Enter the time in 4 digits (“hhmm” format) using the 24 hour system.

In case of 2:30 p.m.:

11443300

3. Press S once.

4. Enter the date in 6 digits using the day-month-year format.

In case of 15 May, 2002:

115500550022

5. Press S twice. A programmed report is printed.

You can change the date format in the Z/PGM mode. If you change the format, follow the

format you changed when setting the date.

Step 4 Set Time and Date

7

When an Error Occurs

When your register goes into an error state, it displays the error message “ ” accompanied with a

warning beep. Clear the error state by pressing c and take an appropriate action.

1. When you enter an over 7-digit number to the department or an over 8-digit number

(79999999) to RA, PO, credit or cheque:

Press c and make a correct entry.

2. When you make an error in key operation:

Press c and make a correct entry.

3. When you make an entry beyond a programmed entry digit limit:

Check if the entered amount is correct. If correct, check the setting of the entry digit limit.

4. When a subtotal exceeds eight digits (79999999):

Press c and then press t, R or C to finalize the transaction at that point.

5. When the number of an item exceeds 3 digits in multiplication entry:

Press c and re-enter a correct number.

Error Escape Function

When an error or something uncontrollable occurs during transaction entry and you cannot keep

the customer waiting, press e twice (following c when in the error state). You can escape the

situation and finalize the transaction as a cash sale at that time. Transaction entries until then are

registered.

8

Basic Sales Entry Operation

1. Set the mode switch to the REG position.

2. Make sure that a paper roll is installed. (Excepting you set the receipt off function)

Before Sales Entries

When selling a department item

An operation example (paid by cash) is shown below.

1. Enter the price for the first department item (in case of 15.00, enter 15:).

2. Press the appropriate department key.

For department 5 to department 8, press s first before pressing the department key.

3. Repeat steps 1 and 2 for all the department items.

4. Press S to display the amount due. (You can omit this step.)

5. Enter the amount received from the customer. (You can omit this step if the amount tendered is

the same as the subtotal.)

6. Press t, and the change due is displayed and the drawer is opened.

7. Tear off the receipt and give it to the customer (in case you programmed receipt printing) with

his or her change displayed.

8. Close the drawer.

• When paid by cheque, press C instead of t.

• When paid by credit, press R instead of t.

• If you preset unit prices to departments, you can omit entering the unit price of the

department item, that is, omit the step 1 shown above. For the programming, refer to

the Department Programming section.

Selling a 5.00 item (dept. 1) and an 8.00 item (dept. 3) for cash and receiving 20.00

from your customer.

5:! 8:# S 20: t

Price and dept. Price and dept. Amount tendered

When selling a PLU item (to use PLU item sales entry, you must program PLUs.)

Enter the PLU code of a PLU item and press P. The PLU item will be registered.

Selling a PLU1 item and a PLU15 item by credit.

1P 15P R

When selling only item by cash (Single Item Cash Sale (SICS) entry)

When a sale is for only one item paid by cash, such as a pack of cigarettes, you can use SICS

function. It is applicable only to department keys programmed for SICS or to PLUs associated with

such departments. The drawer opens after pressing the department or PLU key.

Example

Basic Sales Entry

9

Basic Sales Entry Operation

When entering more than one of the same department or PLU items

You can enter two or more of the same department or PLU item by pressing department or PLU

key repeatedly (repetitive entry), or by using the multiplication key (multiplication entry). It will

be convenient to use the multiplication key when selling the same item in bulk. For operation, refer

to the example shown below.

Repetitive entry

Selling two 2.00 items (dept. 1) and three PLU5 items for cash

2:!! 5PPP t

Multiplication entry

Selling six 1.50 items (dept. 1) and twelve PLU5 items for cheque payment

6x 150! 12x 5P S C

Mixed tender sale

When the amount tendered by cash or cheque is less than the sales amount including tax, the

display shows a deficit and “ ”. To compensate for the deficit, make an additional amount-

tendered entry or make a credit entry.

Your customer pays 8.30 in cash and 50.00 by credit for an including-tax subtotal of

58.30.

S 830 t R

Amount received Displays a

in cash deficit and “ ”

Example

Other Features for Sales Entries

Your cash register provides the following six tax systems.

Your cash register is pre-programmed as manual VAT 1 to 4 system.

Auto VAT 1 to 4 system (automatic operation method using programmed percentages)

This system, at settlement, calculates VAT for taxable 1 through 4 subtotals by using the

corresponding programmed percentages.

Auto tax 1 to 4 system (automatic operation method using programmed percentages)

This system, at settlement, calculates taxes for taxable 1 through 4 subtotals by using the

corresponding programmed percentages, and also adds the calculated taxes to those subtotals,

respectively.

Manual VAT 1 to 4 system (manual entry method using programmed percentages)

This system provides the VAT calculation for taxable 1 through 4 subtotals. This calculation is

performed using the corresponding programmed percentages when V is pressed just after

S.

VAT (Tax) Calculation

10

Other Features for Sales Entries

Manual VAT 1 system (manual entry method for subtotals that uses VAT 1 preset

percentages)

This system enables the VAT calculation for the subtotal. This calculation is performed using the

VAT 1 preset percentage when V is pressed just after S. For this system, the keyed-in VAT

rate can be used. In this case, after pressing S, enter the VAT rate and press V.

Manual tax 1 to 4 system (manual entry method using preset percentages)

This system provides the tax calculation for taxable 1 through 4 subtotals. This calculation is

performed using the corresponding programmed percentages when V is pressed just after

S. After this calculation, you must finalize the transaction.

Auto tax 1 to 3 and auto VAT 1 system

This system enables the calculation on the combination with automatic tax 1 through 3 and

automatic VAT 1. The combination can be any of VAT 1 corresponding to taxable 4 and any of tax

1 trough 3 corresponding to taxable 1 through 3 for each item. The tax amount is calculated

automatically with the percentages previously programmed for these taxes.

VAT/tax calculation for PLU items are performed according to the one set for its

associated department.

If you want to apply a discount or a premium for an item, enter the percent rate and press the

percent key. If you want to apply a discount or premium for the subtotal, enter all the items, press

S and then press the percent key following the percent rate.

Your machine is pre-programmed as discount. If you change to premium, refer to the

percent key programming section. Also you can preset a percent rate. If a percent rate is

preset, you do not have to enter a percent rate before pressing the percent key. For the

programming, also refer to the percent key programming section.

Applying a 20.00% discount to an item belonging to department 3

8:# 20:% t

Applying a 15.00% discount to the subtotal of a transaction

8P 12P 8:! S 15:% t

Example

Discounts and Premiums Using the Percent Key

Your register allows payment entries of foreign currency when you programmed a currency

exchange rate. After items entries or during tendering entries, press E, the subtotal in foreign

currency can be displayed. Then enter the tendered amount in foreign currency if not exact

amount payment, and press a finalization key (t / C or R when programmed). The change

due in domestic currency will be displayed.

• When the amount tendered is short, the deficit is shown in domestic currency.

• If you select "Yes" for cheque and credit operation when tendering in foreign currency in

EURO programming, you can finalize a sale in foreign currency using C or R.

• If you select “Yes” for exchange amount printing for total and change in EURO

programming, you can display a change in foreign currency by pressing E when the

change is displayed in domestic currency. To return to the display in domestic currency,

press E again.

Currency Exchange

11

Other Features for Sales Entries

Selling a department 3 item (price 79.50) in a foreign currency. (Preset exchange rate:

1.550220)

7950# E 130: t

Amount tendered in foreign currency

Example

When you need to open with no sale, for example to make changes, just press t. The drawer

will open.

No Sale

Since your cash register comes with no refund key, make a negative department (see the required

programming on pages 16 and 17) and use it.

Check that the taxable status of the returned item is the same as that of the negative

department. Otherwise the tax will not be calculated correctly.

Refund

Non-add code numbers can be entered and printed on the receipt or journal during the entry of a

sale. Non-add codes can be used for a variety of things. For example: credit numbers, check

numbers, serial numbers, products codes, service charge codes, or any other numbers for later

reference to specific transactions. Enter a code number of up to 8 digits and press S.

Non-add Code Number

When you receive an account from a customer or when you pay amount to a vendor, it is a good

idea to use V or p respectively.

For the received-on-account entry, enter the amount, and press V.

For the paid-out entry, enter the amount, and press p.

The entry limit is 8 digits (79999999), though it is different if you programmed.

Receiving 60.00 on account from a customer whose code number is 12345.

12345S 60: V

Example

Received-on Account and Paid-out Entries

If you should make an error when entering an item into a sale, correct it using the following

procedures.

• Correction of entered numbers

When you enter an incorrect number, delete it by pressing c immediately after the entry.

• Correction of the last entry (direct void)

If you make a mistake when making a department entry, PLU entry, multiplication entry or

repetitive entry (the last entry only), you can correct this by pressing v.

Corrections

12

Other Features for Sales Entries

This report, when taken in the X/F mode, prints the accumulated information of sales.

Taking an X report is a good way to do a mid-day check on daily sales. You can take X reports any

number of times, because they do not affect the cash register’s memory.

To issue an X report, set the mode switch to the X/F position and press t.

X reports for reading of sales

This report, when taken in the Z/PGM mode, prints the same information as an X report. Once this

report had been printed, the cash register’s memory of daily information is cleared and all the

transaction totals are reset to zero. Be sure to issue a Z report at the end of each day.

With a Z report printing, you can also reset GT (ground total).

To issue a Z report, follow the procedure described below.

1. Set the mode switch to the Z/PGM position.

2. If necessary, enter the secret code and press t.

To issue a Z report with resetting of GT:

3. Press C.

4. If necessary, enter the secret code and press C.

To issue a Z report without resetting of GT:

3. Press t.

4. If necessary, enter the secret code and press t.

Z reports for reading and resetting of sales

• Correction of earlier entries (indirect void)

With this function, you can correct department or PLU entry incorrectly made during a transaction

if you find it before finalizing the transaction by pressing t, R or C.

To correct 3P entry to 4P after another correct entry has been made, enter the

following:

3P 1150! 3vP 4P t

Indirect void correct

for

3P entry

• Correction after issuance of receipt

This function allows you to reverse the entries made on an incorrect receipt. The entries are

subtracted from each totalizer and add to a void totalizer. Slide the mode switch to position,

and enter the same details that are on the incorrect receipt. (If necessary, enter the secret code

and press t when you slide the mode switch to position.)

Example

All the data on all of your registrations as well as other transaction information will remain in the

memory of your cash register as long as your cash register has power (Be sure you have live

batteries installed in case of a power failure). This information can be printed in the form of a

report which can be helpful to you in running your business.

Reading and Resetting of Sales

13

Reading and Resetting of Sales

Use this function for on-the-spot checking of individual cash register’s sales data. The sales total is

shown on the display but is not printed nor cleared from the cash register’s memory.

To display the flash report for each individual item, press the following keys in the X/F mode:

Individual department sales Department key

Sales total S

Cash in drawer R

Flash reports for viewing on the display

Reset counter

Grand total

Quantity

Dept. counter

and total

Percent counter

and total

Item void counter

and total

Void mode counter

and total

*

2

Taxable 1 total

Tax 1 (VAT) total

Dept. code

Amount

*

1

Reset symbol

(“X” is printed

in case of

X reports.)

Count of transactions

Sales total

Cash sale counter

and total

Cheque sale counter

and total

Credit sale counter and total

Exchange counter

and total

(in cash tendering)

Exchange counter

and total

(in cheque tendering)

Exchange counter

and total

(in credit tendering)

Received-on account total

Paid-out total

No sale counter

Cash in drawer

*

3

*

4

*

4

Sales report

*

1

Printed in the Z report only.

*

2

Difference by rounding is printed here in case Australian rounding is applied.

*

3

Not printed in case that the exchange rate is set to 0.000000.

*

4

Not printed in case that “Cheque and credit operation when tendering in foreign

currency” is set to “No” on EURO programming, and/or the exchange rate is set to

0.000000.

14

EURO Migration Function

Your register can be modified to correspond with each period set for the introduction of EURO, and

in your register each currency is treated as shown on the table below depending on which period

you are in.

Basically your register can be automatically modified to correspond to the introduction of EURO by

executing automatic EURO modification operation shown below in Z/PGM mode. However, there

are several options you must set depending on your need. So, please carefully conduct necessary

settings.

How currencies are treated in your register

Automatic EURO modification operation

Make sure the mode switch is in the Z/PGM position first, (if necessary, enter the secret code and

press t) and perform the following procedure. Please note that you can perform each

operation only once with the substitution of “A=1”, “A=2” and “A=3”. For example, if you performed

the operation with the substitution of “A=2” first, you cannot perform the operation with the

substitution of “A=1”.

8:S A* S

*A: Enter 1 for the period 1, 2 for the period 2, and 3 for the period 3.

The details of the register system modification are as shown on the following page:

Period 1

After the introduction of

EURO, and before

EURO banknotes and

coins begin to circulate

Exchange key

Domestic currency

Period 2

After EURO banknotes

and coins begin to

circulate, and before

national currency is

withdrawn from

circulation. (Co-

existence of EURO and

national currency)

Domestic currency

Exchange key

Period 3

After the national

currency is withdrawn

from circulation

Domestic currency

Exchange key

EURO

National currency

(DM, F, etc.)

Foreign currency

Currency

15

EURO Migration Function

IMPORTANT

• After the execution of the procedure with “A=1”, treat EURO as foreign currency using E. Set

the EURO conversion rate as the currency conversion rate for E.

• After the execution of the procedure with “A=2”, treat EURO as domestic currency and national

currency as foreign currency using E. Set the EURO conversion rate as the currency conversion

rate for E.

• After the execution of the procedure with “A=3”, treat EURO as domestic currency.

• As for the percent rate for % and HALO setting, the automatic conversion is not made. So, when

your domestic currency becomes EURO, you must change these settings so that they are based

on EURO currency.

• You can receive the amount of exchange (EURO or national currency) in cheque or credit. For

the programming, please refer to EURO programming on page 20.

• When “Exchange amount printing for total and change” is set to “Yes”, you can display a change

in foreign currency by pressing E when the change is displayed in domestic currency.

Checking the current EURO status

You can check the EURO status currently set on the cash register. Set the mode switch to the

Z/PGM position, (if necessary, enter the secret code and press t) and perform the following

procedure. The current EURO status will be printed on the receipt or journal.

8:SS

EURO status

Items

General Z report

GT memory

Conversion of preset prices of Dept./PLU

Exchange amount printing for total and

change

Exchange calculation method

Domestic currency symbol

Domestic currency decimal point position

Exchange currency symbol

Exchange currency decimal point position

Rounding of exchange currency

A=1

(EURO status 1)

Issue

-

Yes

Division

-

[EURO]

2

Round off

A=2

(EURO status 2)

Issue

Clear

Yes

Multiplication

[EURO]

2

Previous domestic currency

symbol

Previous domestic currency

decimal point position

Round off

A=3

(EURO status 3)

Issue

Clear *

1

Yes *

1

No

Multiplication

[EURO]

2

-*

2

-

Round off

• The item marked with “-” remains the same as the previous data.

*

1

: When you perform from EURO status 2, previous data remains unchanged.

*

2

: When you perform from EURO status 1 or 2, “space” is set.

16

Programming

1. Set the mode switch to the Z/PGM mode.

2. If necessary, enter the secret code and press t.

• You can continue programming without printing the programming report by not pressing

S at the end of each program step. However, you must program PLUs independent

from other programming.

• Unless otherwise specified, programming options marked with

* indicate factory setting.

In case of values or number settings, the factory settings are shown with the word,

“Default”.

Preparations for Programming

Your cash register comes with the the ability to program six kinds of tax system. Program a tax

system required by your region, and program tax rates (00.0000% to 99.9999%) on the tax system

you selected.

Programming the Tax System

8

➜

S

➜ A ➜

S

(➜

S

)

Parameter A: Tax system

*Manual VAT 1-4: 0 Auto VAT 1-4: 1 Auto Tax 1-4: 2

Manual VAT 1: 3 Manual Tax 1-4: 4 Auto Tax 1-3 and Auto VAT 1: 5

Programming VAT (Tax) Rate

Parameters

A: VAT (Tax) 1: 1 VAT (Tax) 2: 2 VAT (Tax) 3: 3 VAT (Tax) 4: 4

B: VAT(tax) rate in 6 digits (000000 to 999999) (Default: 000000)

C: Lower tax limit (0 to 9999) only for TAX system. (Default: 0)

9 ➜ S ➜ A ➜ x ➜ B ➜ x ➜ C ➜ S (➜ S)

When lower tax limit is not specified

Tax Programming

Merchandise can be classified into eight departments. Items sold with use of the department keys

can later be printed on a report that shows the quantities sold and sales amounts classified by

department. The data is useful for making purchasing decisions and other store operations.

Departments can be assigned to articles whose prices were set using PLU function.

When using a department key, you must set the parameters to specify the department status, such

as plus or minus sign. Also prices can be assigned directly to department keys for frequently

purchased items, which enables you to enter the prices by simply pressing the department keys.

Department Programming

17

Programming

Programming the department status

ABCDEFG* ➜

x

➜ (

s

➜ ) Department key (➜

S

)

(Press s to program departments 5 to 8.)

Parameters: Selection: Entry:

A Sign +/- + sign* 0

- sign 1

B Normal/SICS (Single Item Cash Sale) Normal* 0

SICS 1

C VAT4 or TAX4 No* 0

Yes 1

D VAT3 or TAX3 No* 0

Yes 1

E VAT2 or TAX2 No* 0

Yes 1

F VAT1 or TAX1 No 0

Yes* 1

G Entry digit limit (0 to 7 digits) 0 through 7 (default: 7)

• Sign

Assign + sign to departments in which normal sale amounts are to be entered, and - sign to

departments in which payments for items such as refunds, bottle returns or other minus

transactions are to be entered.

• SICS (Single Item Cash Sale)

This allows the operator to finalize the transaction entry by entering the unit price of one item and

pressing the department key set for SICS. If the unit price is preset for the department key, you

can finalize the transaction by pressing the department key only.

• Entry digit limit

Setting this parameter for applicable departments prevents the accidental entry of too large an

amount during a sale. For example, if the highest entry to be allowed is 9.99, enter 3. If 0 is

entered you cannot enter a price and only a preset price can be entered.

Programming preset unit price

Unit price

(max. 5 digits) ➜ (

s

➜) Department key (➜

S

) (Default: 0.00)

(Press s to program departments 5 to 8.)

The PLU function allow speedy key entries whereby a preset price is automatically called up when

a code is entered. Up to 80 PLU settings are possible. Each PLU belongs to a department and

acquires the parameters of the department. The cash register was factory preset so that PLU1 to

10 are assigned to department 1 and unit price 0.00.

(Press s to program departments 5 to 8.)

To disable a PLU, enter the PLU code and press P, then press v and S.

PLU code ➜ P ➜ Unit price (max. 6 digits) ➜ (s ➜) Department key ➜ S

For the next PLU code programming

When the next PLU code to be programmed does not directory follow the one just entered.

PLU Programming

18

Programming

% can be programmed as a discount key or premium key. As a default, % is programmed as a

discount key. Also you can program a percent rate for %.

When 00.00% is programmed, use of preset percent rate is prohibited. (factory setting)

Programming the percent key function (discount or premium)

1

for discount or

0

for premium ➜

x

➜

%

(➜

S

)

Programming the percent rate (00.00 to 99.99%)

Percent rate in 4 digits (0000 to 9999) ➜

%

(➜

S

)

Percent Key Programming

To handle a foreign currency, you can program a currency exchange rate (000.000000% to

999.999999%) for the exchange key.

When 000.000000% is programmed, use of E is prohibited (factory preset).

Currency exchange rate in 9 digits (000000000 to 999999999) ➜

E

(➜

S

)

Exchange Key Programming

You can program a printing format of the receipt or journal by using the following eight kinds of

parameters.

2

➜

S

➜ ABCDEFGH ➜

S

(➜

S

)

Parameters: Selection: Entry:

A Currency symbol for domestic currency Space* 0

EURO 1

B Printing receipt/journal in the REG mode Yes (Receipt ON)* 0

(Receipt ON/OFF function) No (Receipt OFF) 1

C Printing format Journal format* 0

Receipt format 1

D Date printing Yes* 0

No 1

E Time printing Yes* 0

No 1

F Receipt number printing Yes* 0

No 1

G Taxable subtotal printing Yes* 0

No 1

H Subtotal printing with a press of

S

Yes 0

No* 1

• Printing format

When receipt format is selected, the take-up spool does not move.

Printing Format Programming

Page is loading ...

Weider XE-A101 User manual

Weider XE-A101 User manual

in other languages

Related papers

Other documents