Digitus DA-71540 Owner's manual

Digitus
Brand
Digitus
Model
DA-71540
Category
HDD/SSD docking stations
Type
Owner's manual

Digitus DA-71540 is a USB3.0 to Dual SATA (6G) Docking Station with Offline Clone Function. It allows you to connect two 2.5" or 3.5" SATA HDDs to your computer via a single USB3.0 port. The docking station supports data transfer speeds of up to 5 Gbps and is backward compatible with USB 2.0 and 1.1.

One of the key features of the Digitus DA-71540 is its offline clone function. This function allows you to clone the contents of one HDD to another without having to connect the docking station to a computer. Simply insert the source and target HDDs into the docking station, press the "Clone" button, and the cloning process will begin. The progress of the cloning process is indicated by LED lights on the front of the docking station.

Digitus DA-71540 is a USB3.0 to Dual SATA (6G) Docking Station with Offline Clone Function. It allows you to connect two 2.5" or 3.5" SATA HDDs to your computer via a single USB3.0 port. The docking station supports data transfer speeds of up to 5 Gbps and is backward compatible with USB 2.0 and 1.1.

One of the key features of the Digitus DA-71540 is its offline clone function. This function allows you to clone the contents of one HDD to another without having to connect the docking station to a computer. Simply insert the source and target HDDs into the docking station, press the "Clone" button, and the cloning process will begin. The progress of the cloning process is indicated by LED lights on the front of the docking station.

USB3.0 to Dual SATA (6G)
Docking Station
(With Offline Clone Function)
Manual
DA-71540
Features
- Super Speed (5 Gbps) / high-speed (480 Mbps) / full-speed (12 Mbps)
- Supports SATA6G & SATA3G & SATA1.5G
- Supports offline duplicate function, all data or system files copy into your target
hard disk by one simple button
- Supports 2 x 3.5" or 2.5" SATA HDD plug-in one compact unit, data can be transfer
between 2.5”and 3.5” SATA HDD
- Two hard drives can be read & write at the same time
- The dual bay docking station connects to the computer via USB3.0
- Hot swappable, without driver installation
- LED progress indicator shows clear clone status
CLONE
Offline Duplicate
Function
1. This product supports offline duplicate function which can clone the
HDD directly without connecting to computers by USB port.
2. Insert the HDDs to "A"&"B", A is the HDD to be cloned, B is the target
HDD to cloning, HDDs capacity requires B≥A
3. Start cloning: Press "Clone" button on the product about 3 seconds, when
release the button “The LED indicator of 100% will light up”, and quickly
click "Clone", then it start cloning. Indicator lights (25%, 50%, 75%, 100%)
flash up in turn during cloning, and whole lights on after complete Cloning
is done.
Sleep
Mode
1. After finishing cloning HDDs under offline duplicate mode, product goes to
sleep mode if there were no operations in 30min and HDDs stop running.
Power Indicator the light flash-up every 3 seconds, and other progress
indicator lights and disk LED light still work, that means clone is done and
goes to sleep mode without any operations. HDDs will wake up again to
stand-by mode by press clone button shortly.
2. When the product connects to computer, it goes to sleep mode if there
were no reading or writing on hard disk in 30mins and HDDs stop running.
Power Indicator light flashes in every 3 seconds, the A/B disk LED keep
lights up, It starts flashing when computer reads and writes again.
FAQ
1. Unable to start cloning: Please check whether the actual capacity of B disk
is higher than A disk (B≥A), otherwise it won’t work when A disk’s actual
capacity is higher than B disk’s. (B<A)
2. Indicator light stops flashing up during offline duplicating: it might because
of disk bad sectors so that data couldn’t be cloned as usual. It’s better to
change a good disk.
3. After cloning, the rest capacity of B disk is showed and operated via
“Computer management - Storage - Disk management”.
4. Why over 2TB hard disk couldn’t be identified by USB? Because the
maximum capacity of hard disk which Windows XP can supports is 2TB
and couldn’t be identified by system if over 2TB. It only supports after
upgrading the operating system above Vista (64 bit) version and we
suggest changing hard disk into a GPT disk partition, or the operating
system will not support over 2 TB disk partitions.
5. Please make sure that B hard disk data can be covered before cloning
data. Because once you start cloning, B hard disk partition methods and
data are completely cloned as A hard disk. Our company does NOT
undertake any responsibility for data or economy loss which could bring
by damaged data.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Digitus DA-71540 Owner's manual

Digitus
Brand
Digitus
Model
DA-71540
Category
HDD/SSD docking stations
Type
Owner's manual

Digitus DA-71540 is a USB3.0 to Dual SATA (6G) Docking Station with Offline Clone Function. It allows you to connect two 2.5" or 3.5" SATA HDDs to your computer via a single USB3.0 port. The docking station supports data transfer speeds of up to 5 Gbps and is backward compatible with USB 2.0 and 1.1.

One of the key features of the Digitus DA-71540 is its offline clone function. This function allows you to clone the contents of one HDD to another without having to connect the docking station to a computer. Simply insert the source and target HDDs into the docking station, press the "Clone" button, and the cloning process will begin. The progress of the cloning process is indicated by LED lights on the front of the docking station.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents