VoteCom VC02 User manual

User Manual

Wi-Fi Camera Alarm Clock

Contents

1.

BUTTONS AND LIGHTS .................................. 1

2.

CONDITIONS AND PREPARATIONS ................ 2

2.1

I

NSERT

M

ICRO

SD

CARD

...................................... 2

2.2

C

HARGE

............................................................ 2

2.3

P

OWER ON

/

OFF THE CAMERA

............................... 2

2.4

R

ESET

............................................................... 3

3.

PRIMARY FUNCTIONS ................................... 3

F

OR DETAILS

,

PLEASE FOLLOW THE STEPS BELOW

. ............ 4

3.1

S

CAN THE

QR

TO DOWNLOAD THE

A

PP

VOTECOM. . 4

3.2

O

PEN THE

A

PP

,

CHOOSE

W

I

-F

I

C

AMERA

. ................ 5

3.3

T

AP

C

ONNECT

C

AMERA

,

AND CONNECT THE CAMERA TO

YOUR SMARTPHONE VIA HOTSPOT

(UID). ...................... 6

3.4

P

LEASE CHOOSE THE WAY OF CONNECTING

. .............. 7

3.5

D

EVICE LIST

..................................................... 11

3.6

D

EVICE

S

ETTINGS

.............................................. 12

3.7

L

IVE

V

IDEO

...................................................... 18

4.

USE MORE .................................................. 19

5.

SPECIFICATIONS .......................................... 20

6.

TROUBLESHOOT ......................................... 21

Here come some tips for you. Please go

through the following items before setup.

Users should be responsible for any damage

and abnormalities due to improper operation.

1. Make sure you removed the plastic

insulating slip inside the back cover.

2. Before power it on, please charge it for

at least 1h for easy setup (maybe the

battery has run out). Or keep charging it

all the time.

3. Make sure you have connected your

VOTECOM Wi-Fi camera to your

smartphone via hotspot (named the

camera’s UID pasted on the camera)

before connecting it to a Wi-Fi.

4. Make sure your Wi-Fi is in 2.4G mode.

Ask the router manufacturer for help if

you need.

5. Simply reset it if your VOTECOM Wi-Fi

camera performs abnormally (such as

your smartphone couldn’t find the

hotspot, it can’t connect to Wi-Fi, or it

goes offline frequently).

For details, please refer to instructions

below.

VOTECOM Customer Care

1

1. Buttons and Lights

2

2. Conditions and Preparations

Open the back cover, and remove the plastic

insulating slip inside.

2.1 Insert Micro SD card

Here comes a Micro SD card for SD card

recording. Hold golden fingers of the Micro SD

card downwards, and then insert it into the

slot.

2.2 Charge

Please charge it before the first use. It can

support 1.5h after fully charged. To charge,

simply connect it to your adapter (DC 5V)

through the USB cord included.

Keep charging it if you use it for continuous

working. In this case, to maintain battery life

and avoid getting hot, we recommend you

remove the battery.

Please note that files will be saved

automatically when the battery runs out.

2.3 Power on/off the camera

2.3.1 Power on: Press “Power” button, it will

3

create a hotspot (named the camera’s UID

pasted on the camera).

2.3.2 Power off: Press “Power” button again to

power it off.

Please note that the clock is always working

until the battery runs out, no matter the

camera is on or off.

2.4 Reset

Simply reset it if the camera performs

abnormally. When the camera is on, just press

and hold “Reset” button for about 5s until

indicator lights turn off, it will create the

hotspot (named the camera’s UID pasted on

the camera) within 15s.

3. Primary Functions

Functions stated below are primary features of

this item. Download the App VOTECOM, go

step by step to set it up.

Please note: 1. It only supports 2.4G Wi-Fi

network. 2. The default password of the

4

camera is 8888.

To set it up, simply go through the following

process:

Download the App

Connect your smartphone to the device via

hotspot (named the camera’s UID pasted on

the camera)

Connect the device to Wi-Fi through the App

Congratulations. Enjoy this gadget

For details, please follow the steps below.

3.1 Scan the QR to download the App

VOTECOM.

You can also download the App VOTECOM

from Google Play Store (for Android) or Apple

Store (for iOS).

5

3.2 Open the App, choose Wi-Fi Camera.

6

3.3 Tap Connect Camera, and connect the

camera to your smartphone via hotspot

(UID).

Important Notice

In this step, you should choose the

network named UID pasted on the

camera (beginning with CM or PQ), NOT

YOUR HOME WI-FI.

7

3.4 Please choose the way of connecting.

Way1 Connect device to wireless router

In this way, you can view real-time video

anywhere.

8

 Choose your Wi-Fi, enter its password and

then join.

9

 Tap the icon to enter Device List. And then

go directly to item 3.5.

Way2 Connect directly by Point-to-Point

Your smartphone can connect directly by

Point-to-Point (hotspot) when your

smartphone is near.

In this way, it can’t support viewing real-time

video remotely.

10

Tap the right arrow icon to enter Device List.

If you want to connect your camera to Wi-Fi,

please go to Device list> Settings>Device

Settings>Wi-Fi Settings.

11

3.5 Device list

Tap it to add a new device

Tap it to add as many as 4 cameras in one

page

Motion detection is enabled

Motion detection is disabled

Tap it to enter Settings

12

Tap it to view real-time video

Tap it to view snapshots captured in the

real-time video interface

Tap it to view videos recorded in the

real-time video interface or Micro SD card

Tap it to view photos taken when it is

alarming

3.6 Device Settings

Tap to enter Settings>Device Settings.

3.6.1 Alarm Settings



Motion detection sensitivity: When

motion detection is enabled, the device

will send you an alarm automatically if

motion is detected. You can choose a

sensitivity level for Motion detection. It

has 7 levels. When you choose “disabled”,

motion detection will be closed.



Alarm schedule: You can set a time period

only in which it sends alarm information to

13

you.

 Warming Tone: After enabling motion

detection (Motion detection sensitivity is

not set to “disabled”), you can enable the

camera to send out alarm sound or not.

This function applies to certain types. For

some types, if smoke/gas detection is

available, the alarm also can be triggered.

14

When it sounds an alarm, you can tap the

icon to stop it.

 E-mail Alert: After enabling motion

detection, you can enable or disable the

E-mail alarm. Just go to “Email Settings” to

set it, then it will send you photos shot at

the moment it detects movement. For

some types, if smoke/gas detection is

available, the alarm also can be triggered.

 Alarm interval: After enabling motion

detection, if motion is detected, the

camera will perform alarm. You can type in

a number between 30 and 300 to set the

time interval between two alarms.

 Push notifications: You can enable or

disable this functionality. If you enable it,

the App will send you push notifications

even if you exit the App in

iOS-powered devices, or run the App in

background in Android-powered devices.

 On-Screen Display: If you enable this

15

functionality, current time stamp will show

up in the real-time video.

 Certain types with smoke/gas detection

functionality have a more item to enable

or disable smoke/gas detection alarm.

After setting, please tap “OK” to save.

3.6.2 SD Card Record Settings



Record: If you want to record all the time,

16

please choose “All day”. If you choose

“On alarm”, you need to enable motion

detection. You can also choose “Timing

Record” to set a time only in which it

records videos into Micro SD card.

 Resolution: You can choose the resolution

of video recorded in the Micro SD card

(not live video).

 File length (minute): It generates a file

every 3 minutes by default (that means it

will automatically generate a video file

every 3 minutes and continue recording).

You can type in a number to set file length

between 1 and 60 minutes.

 Record sound: When you enable this

functionality, it will record sound while

recording video.

 Loop recording: When you enable this

functionality, it will override the oldest file

and continue recording even if the Micro

SD card is full.

17

After setting, please tap “OK” to save.

3.6.3 Email Settings

Type in E-mail addresses for a sender and as

many as 4 recipients. Fill in “User” and

“Password” with the sender’s E-mail addresses

and corresponding password, respectively.

Then tap “OK” to save.

Page is loading ...

VoteCom VC02 User manual

This manual is also suitable for

VoteCom VC02 User manual

Other documents