Phoenix USA GDG01 Owner's manual

Brand: Phoenix USA

Model: GDG01

Type: Owner's manual

27448.doc

DOT Liner with Lug nuts and Tubular Stud Extenders

Fits sets: GDG01

Packing List: (add images of each item)

2 – Front wheel simulators, PGDGxxxFWL

2 – Rear wheel simulators, PGDGxxxRWL

8 – Lugnut covers with built in jamnut, PGDGxxLNT

8 – Stud extenders, PGDGxxxTSX

4 – Center hub logos, CLPH2

1 – Installation tool, PGD168TOL

Installation instructions

Note: This system can be installed with the installation tool provided. No other tools are

necessary. Do NOT use power tools for installation. Phoenix USA, Inc. recommends

storing the installation tool with the vehicle’s tire tool for future use.

1. Check parts listing and ensure all parts are available. If missing any parts, please

call customer service at 1-800-786-8785.

2. Do not remove the original equipment lug nuts.

3. Clean wheel and rim and remove all dirt, debris and grease with approved cleaner.

4. Front: Determine correct placement of simulator by aligning the handhole cutout

with the valve stem.

5. Rear: Determine correct placement of simulator by aligning the handholes of

simulator with the handholes of the wheel.

6. Install two stud extenders.

7. Place simulator over the exposed stud extenders “evenly”.

8. Install two jam nut/lugnut covers per simulator onto the two stud extenders.

9. Use installation tool (PGD205TOL) to tighten jamnuts. Do NOT use power tools

for installation.

10. Remove the paper backing from the included logos (CPLH2)

11. Place logo in center indentation of simulator.

12. Repeat process for each wheel.

Removal of wheel simulators

1. Find the two jamnut/lugnut covers that have an indicator notch on the side. They

should be located directly opposite from each other on the axle.

2. Remove the jamnut by using installation tool.

27448.doc

3. Remove the wheel liner and place in position and surface so as not to scratch the

liner.

4. Remove stud extenders using installation tool.

5. Remove spacers.

Caring for your wheel simulators

The care and maintenance of your Phoenix USA, Inc. stainless steel wheel product is

simple. Your wheel simulators are made of high quality stainless steel T304 ensuring

you a mirror finish shine and should never rust if properly cared for.

Regular care

1. Rinse with clean water to remove loose dirt and dust.

2. Clean with mild soap and water or use a cleaner specially formulated for stainless

steel. Ensure you use a non-chlorinated solvent in order to avoid leaving residues

of chloride ions in crevices and other locations where they can initiate crevice

attack, pitting and/or stress corrosion later on.

3. Use soft cloth and non abrasive cleaners on your stainless steel simulators.

4. Rinse thoroughly with clean water to remove excess soap and dirt.

5. Repeat above steps as needed.

6. Keep wheels and simulators clean to ensure years of enjoyment of your

investment.

Phoenix USA, Inc. Wheel Simulator Limited Warranty

Phoenix USA, Inc. warrants the stainless steel wheel simulators for a period of three (3)

years from the date of original purchase against manufacturer defects in materials,

workmanship, and finish under normal use. The warranty is limited to repair and

replacement of the product and does not include any charges to remove or re-install the

product, labor, freight, inconvenience, consequential damage or any other cost or

expenses. The original purchaser must return defective product to Phoenix USA, Inc.

Exclusions from warranty: The warranty of Phoenix USA, Inc. does not extend to the

damage to the products caused by intentional misconduct, negligence, abuse, misuse,

road hazards such as gravel or other debris, modifications or alterations to the product,

improper installation, uses of the product contrary to the product information sheet which

accompanies the product or normal wear and tear.

Exercise of right of warranty: The warranty is conditioned upon the return of the product

to the Phoenix USA, Inc. at the expense of the consumer with date of purchase and

invoice number if available. To return to Phoenix USA, Inc., call customer service at

(800) 786-8785 and a Return Goods Authorization number will be issued for return and

inspection. If it is determined that the product returned was defective because of

manufacturing defects or workmanship, Phoenix USA, Inc. will repair or replace the

product and return it to the customer at no expense to the customer. If the defect was not

due to a defect in manufacturing or workmanship, the product will be returned to the

customer if customer pays all the transportation expenses. If not, the product will be held

for a period of thirty (30) days for the customer to make arrangements to pick-up the

product. After that time, the product will be disposed of by Phoenix USA, Inc.

Phoenix USA, Inc. Stainless steel wheel simulator products are protected under one or more of

the following patents: #4932724; #5096263; #5193884; #5205614; #5205616; #5277478;

27448.doc

#5286093; #5645324; #5669672; #5676430, #5695257; #5722735; #5890773; #6152537;

#6511132; #7156470; #D536291; D538726; D538727; D566028; 7467829; other patents

pending.

Phoenix USA GDG01 Owner's manual

Brand: Phoenix USA

Model: GDG01

Type: Owner's manual

Download PDF

report

Phoenix USA GDG01 Owner's manual

Phoenix USA GDG01 Owner's manual

Other documents