OPERATORS MANUAL
Electric String Trimmer
Model
HTE381201 HTE461501
This Book Contains Important Information Regarding:
SAFETY, ASSEMBLY, OPERATION AND MAINTENANCE.
Please Read And Keep This Book For Future Reference.
Record The Following Information About Your Unit. This Information
Is Necessary When Ordering Parts Or In Case Of Loss Or Theft.
Serial Number:
F-041554C
TABLE OF CONTENTS
2
F–041554C
WARRANTY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATOR’S INFORMATION 3. . . . . . . . . . . . . . . . . . . .
RESPONSIBILITY OF OPERATOR 3. . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY RULES 3. . . . . . . . . . . . . . . . . . . .
INTERNATIONAL SYMBOLS 6. . . . . . . . . . . . . . . . . . . . .
SHIPPING CARTON CONTENTS 7. . . . . . . . . . . . . . . . .
KNOW YOUR TOOL 8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND SERVICE 14. . . . . . . . . . . . . . . . . .
CLEANING AND STORAGE 15. . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 16. . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES AND REPLACEMENT PARTS 17. . . . .
NOTES 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in material and work-
manship under normal use and service for a period of Two (2) Years from the date of purchase. Subject
to the terms and conditions noted in this Limited Warranty, we shall, at our option, repair or replace at no
cost to the original purchaser any part covered by this Limited Warranty during the applicable warranty
period.
The limited warranty does not cover the Normal Wear Parts. Depending upon the type of your product,
the Normal Wear Parts are defined as cutting parts/attachments including blades, cutting lines, spring cap,
inner spool and outer spool cover. These parts are warranted to be free from defects in material and work-
manship as delivered with the product.
This Murray, Inc. Two (2) Year Limited Warranty is your exclusive remedy; however, this warranty is void
or does not apply to any unit that has been tampered with, altered, misused, abused or used for rental or
other commercial and/or professional (non–homeowner and income–producing) uses. Your warranty
does not cover minor mechanical adjustments which are not due to any defect in material or workmanship.
For assistance in making such adjustments, consult your Operator’s Manual.
To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, Please call us at 1–800–251–8007
(US), or 1–800–661–6662 (Canada).
This Murray, Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. This Limited Warranty is given in lieu of all other expressed and
implied warranties including the implied warranty of merchantability and warranty of fitness for a particular
purpose. If you need additional information on this written warranty or assistance in obtaining service, visit
us at: www.murray.com.
MURRAY, INC. TWO YEAR LIMITED WARRANTY
3
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
BEFORE YOU USE THIS UNIT. The instructions are written for
a person with some mechanical ability. Like most service books,
not all the steps are described. Steps on how to loosen or tighten
fasteners are steps anyone can follow with some mechanical
ability.
Know your product: If you understand the unit and how the
unit operates, you will get the best performance. As you read
this manual, compare the illustrations to the unit. Learn the
location and the function of the controls. To help prevent an
accident, follow the operating instructions and the safety rules.
Keep this manual for future reference.
IMPORTANT: Many units are not assembled and are sold in
cartons. It is the responsibility of the operator to make sure the
assembly instructions in this manual are exactly followed. On
assembled units, it is the operators responsibility to make sure
the unit is correctly assembled. The operator must carefully
check the unit according to the instructions in this manual before
it is first used.
RESPONSIBILITY OF THE OPERATOR
The responsibility of the operator is to follow the
instructions below.
Carefully read and follow all safety rules. The rules for safe
operation and the other instructions in this manual must be
reviewed with any operator of this unit.
Before using the product for the first time, follow all the
preparation instructions.
Make sure the operator of the unit understands and knows
how to correctly use all the controls.
Correctly maintain the unit.
Service the unit only with authorized or approved
replacement parts.
CAUTION: The use of any trimmer may be hazardous. If the rotating
cutting line touches your body, it will cut you. When it hits solid
foreign objects such as rocks or bits of metal, it may fling them to
bystanders or the operator.
OPERATORS INFORMATION
WARNING:
When using electric gardening appliances,
basic safety precautions should always be
followed to reduce the risk of fire, electric
shock and personal injury.
Careless or improper use may cause
serious or even fatal injury.
READ AND UNDERSTAND ALL
INSTRUCTIONS.
• This is a double-insulated appliance. When
servicing use only identical replacement
parts.
• This appliance has a polarized plug (one
blade is wider than the other) and will
require the use of a polarized extension
cord. The appliance plug will fit into a
polarized extension cord only one way. If the
plug does not fit fully into the extension cord,
reverse the plug. If the plug still does not fit,
obtain a correct polarized extension cord. A
polarized extension cord will require the use
of a polarized wall outlet.
• This plug will fit into the polarized wall outlet
only one way. If the plug does not fit fully
into the wall outlet, reverse the plug. If the
plug still does not fit, contact a qualified
electrician to install the proper wall outlet.
• Do not change the equipment plug,
extension cord receptacle, or extension cord
plug in any way.
IMPORTANT SAFETY INSTRUCTIONS
F-041554C
4
IMPORTANT SAFETY INSTRUCTIONS
• Avoid Dangerous Environment Dont use
appliances in damp or wet locations.
• Dont use in rain or snow.
• Keep Children Away All visitors should be
kept 50 feets away from work area.
• Dress Properly Do not wear loose clothing
or jewelry. They can be caught in moving
parts. Use of rubber gloves and substantial
footwear is recommended when working
outdoors. Wear protective hair covering to
contain long hair. Wear heavy, long pants,
boots, gloves and a long sleeve shirt during
operation to reduce the risk of injury that
may be caused by flying debris.
• Use Safety Glasses Always use face or
dust mask if operation is dusty.
• Use Right Appliance Do not use appliance
for any job except that for which it is
intended.
• Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the
circuit(s) or outlet(s) to be used for the
gardening appliance. Receptacles are
available having built-in GFCI protection and
may be used for this measure of safety
• Warning To reduce the risk of electric
shock, use only with an extension cord
intended for outdoor use, such as an
extension cord of cord type SW-A, SOW-A,
STW-A, STOW-A, SJW-A, SJOW-A, SJTW-
A. or SJTOW-A.
• Types SW, SOW, STW, STOW, SJW,
SJOW, SJTW, and SJTOW are alternative
designations to Types SW-A, SOW-A, STW-
A, STOW-A, SJW-A, SJOW-A, SJTW-A,
and SJTOW-A, respectfully.
• Extension Cord Make sure your extension
cord is in good condition. When using an
extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized extension cord will
cause a drop in line voltage resulting in loss
of power and overheating.
• See the following Table for the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the gage
number, the heavier the cord.
Cord length (ft) 25 50 100 15
0
Wire size (AWG) 18 16 14 1
2
Minimum Wire Size For Extension Cords
• To reduce the risk of disconnection of
appliance cord from the extension cord
during operating. Secure extension cord as
show in the Assembly section of this
manual.
• Avoid Unintentional Starting Dont carry
plugged-in appliance with finger on switch.
Be sure switch is off when plugging in.
• Dont Abuse Cord Never carry appliance
by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and
sharp edges.
• Dont grasp the exposed cutting blades or
cutting edges when picking up or holding the
appliance.
• Dont Force Appliance It will do the job
better and with less likelihood of a risk of
injury at the rate for which it was designed.
• Dont Overreach Keep proper footing and
balance at all times.
• Stay Alert Watch what you are doing. Use
common sense. Do not operate appliance
when you are tired.
• Disconnect the appliance from the power
supply when not in use, before servicing,
when changing accessories.
• Store Idle Appliances Indoors When not in
use, appliances should be stored indoors in
dry, and high or locked-up place out of
reach of children.
• Maintain Appliance With Care Keep
cutting edge sharp and clean for best
performance and to reduce the risk of injury.
Follow instructions for lubricating and
changing accessories. Inspect appliance
cord periodically, and if damaged, have it
repaired by an authorized service facility.
Inspect extension cords periodically and
replace if damaged. Keep handles dry,
clean, and free from oil and grease.
• Check Damaged Parts Before further use
of the appliance, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
F-041554C
5
alignment of moving parts, binding of
moving parts, breakage of parts, mounting,
and any other condition that may affect its
operation. A guard or other part that is
damaged should be properly repaired or
replaced.
• Keep guards in place and in working order.
• Keep blades sharp.
• Keep hands and feet away from cutting
area.
• When servicing use only identical
replacement parts authorized by Murray Inc.
Use of any other parts or accessories could
lead to injury to user, or damage to the unit.
• Do not attempt any maintenance, repair or
replacement work not described in your
operators manual.
• Clear the area to be cut before each use.
Remove all objects such as rocks, broken
glass, nails, wire, or string which can be
thrown or become entangled in the cutting
attachment. Clear the area of children,
bystanders, and pets.
• Use the unit only in daylight or good artificial
light.
• Operate the unit only outdoors in a
ventilated area.
• Keep hair, loose clothing, fingers, hands and
all parts of body away from openings and
moving parts.
• If you strike or become entangled with a
foreign object, stop and unplug the unit
immediately and check for damage. Do not
operate before repairing damage. Do not
operate with loose or damaged parts.
• Always stop the unit when operation is
delayed or when walking from one work
location to another.
• Always turn off the unit and make sure the
cutting parts have stopped before putting
the unit down.
• Stop and unplug the unit for maintenance,
repair, or for changing the cutting
attachment or other attachments.
• Inspect all extension cords and the unit
power connection periodically. Replace the
cords if any defects or damage appear.
• Keep unit clean of vegetation and other
materials. They may become lodged
between the cutting attachment and shield.
• Clean after each use. Allow the unit to cool
before storing or transporting.
• Never douse or squirt the unit with water or
any other liquid. Keep handles dry, clean
and free from debris.
• When replacing cutting line, use only
identical 0.065 inch nylon line. Do not use
heavier lines than recommended by Murray.
Do not use line materials of other types
like metal wire, rope, and the like.
• Keep the unit below waist level.
• Do not operate unit without trimming line(s)
extended, and the proper line installed. Do
not extend the trimming line over 1 inch
beyond the length of the shield.
Save these instructions.
Refer to them often and use them to instruct other users.
If you loan someone this unit, also loan them these instructions.
IMPORTANT SAFETY INSTRUCTIONS
F-041554C
6
INTERNATIONAL SYMBOLS
Safety And International Symbols
Some of the following pictorials are located on your unit or on literature supplied with the product.
Before you operate the unit, learn and understand the purpose for each pictorial.
Symbol Meaning
Safety Alert Symbol Indicating Warning, Caution or Danger
Please Read Operators Manual
Wear Eye And Hearing Protection
Keep Bystanders Away
Keep Hands Away from Blade
Do Not Use in The Rain
Watch for Thrown Objects
Double Insulation
F-041554C
7
SHIPPING CARTON
Assist Handle Set, including:
Handle X 1
Securing Bolt X 1
Shield Set, including:
Shield X 1
Fastening Screws X 1
The Part Bag include the following items :
Guide Wheel X 1
F-041554C
8
KNOW YOUR TRIMMER
Extension
Cord Hook
Trigger Handle
Handle Lock
Assist Handle
Shaft Adjustment
Button
Guide
Wheel
Cutting Head
Tilt Adjusting
Lever
Shield
Line Limiter
F-041554C
9
ASSEMBLY
Mounting The Assist Handle (Fig. I)
1. Release the Securing Bolt (1) on the Assist
Handle set.
2. Fit the Assist Handle (2) to the Handle
Mount (3). (See the Figure for the right
direction of the handle. The nipples on the
Handle Mount should aline to the holes on
the Handle.)
3. Fasten the Securing Bolts (1).
Adjusting The Shaft Length To Most
Comfortable Position (Fig. II)
1. Press the Shaft Adjustment Button (6)
upwards and hold it.
2. Slide the upper shaft to adjust the shaft
length to your most comfortable position.
3. Release the Shaft Adjustment Button (6) and
let the shaft lock in the position.
(3)
(1)
(2)
(6)
(5)
Fig. I
Fig. II
Fig. III
Mounting The Shield (Fig. II)
1. Insert the bottom of the main body including
cutting line(s) into the hole of the Shield (5).
See the picture for right direction to put the
Shield.
2. Press and turn the Shield counter-clockwise
till it is fasten.
Note: If you find the screw hole on the
Shield doesnt align with the hole on the
trimmer body, that means the shield is in
wrong direction. In this case, re-mount
the shield in the other direction.
3. Use the long screw from the part bag to
fasten the Shield to the main body of the
trimmer.
F-041554C
10
Securing The Extension Cord Connection
(Fig. VI)
Use the cord hook when you connect the
extension cord to the power cord to prevent
disconnection.
ASSEMBLY
Adjusting The Cutting Line (Fig. IV)
1. If the trimmer is used for the first time, the
cutting line should be pulled out with force.
2. Press the Spring Cap (7) while pulling out
the line to the appropriate length.
3. The ideal length for line is shown in the
figure. If you are not sure, make the line a
little longer. It will be cut to the right length
by the Line Limiter (9) on the Shield (5)
when the trimmer is started.
You can also advance the cutting line by the
following directions:
(7)
(5)
Advancing The Cutting Line (Fig. V)
To advance the line, tap the bottom of the
cutting head on the ground while the trimmer is
running at full speed. The Line Limiter attached
to the Shield will cut the line to the proper
length.
For best results, tap the Spring Cap (7) on bare
ground or hard soil. If line release is attempted
in tall grass, the motor may stall.
Line Limiter
(7)
Tap
(9)
Fig. IV
Fig. V
Fig. VI
F-041554C
11
ASSEMBLY
Mounting The Guide Wheel (Optional)
(Fig. VII)
The Guide Wheel is very useful in edging
operation. (See Edging Operation in Operating
Section.)
1. Take the two short fastening screws from
the part bag.
2. Install the Guide Wheel at the position
shown in the figure and fasten the two
screws.
The Guide Wheel is only needed for edging
operation.
OPERATING
Holding The Trimmer (Fig. VIII)
Before operating the trimmer, stand in the
operating position (reference Fig. VIII) and
check for the following:
1. Operator wearing eye protection and proper
clothing.
2. Left arm straight, hand holding Assist
Handle.
3. Right arm slightly bent, hand holding Trigger
Handle.
4. With operator standing in straight upright
position, the Spring Cap is parallel to the
ground and easily contacts the material to
be cut.
Always take this position when operating.
To Start Unit (Fig. IX)
1. Plug in the trimmer and secure the
extension cord connection.
2. Depress the trigger.
To Stop Unit (Fig. IX)
1. Release the trigger.
2. Unplug the trimmer for moving,
checking, adjusting or maintaining the
unit.
Fig. VII
Fig. VIII
Fig. IX
F-041554C
12
OPERATING
To Convert To Edging Operation (Fig. XI)
1. Switch off the power and unplug the trimmer.
2. To turn the handle around: press the Handle
Lock and turn the handle 180 degrees
clockwise until it is locked. (Fig. XI)
3. Release the Handle Lock.
4. Mount the Guide Wheel. (See Mounting the
Guide Wheel in Assembly Section.)
Edging Operation (Fig XII)
See the figure for proper edging operation
position.
Adjusting Shaft Tilt Angle (Fig. X)
1. Switch off the power and unplug the trimmer.
2. Press the Tilt Adjusting Lever with one hand
while adjusting the shaft tilt angle with the
other hand.
3. Release the Tilt Adjusting Lever.
Fig. X
Fig. XI
Fig. XII
F-041554C
13
OPERATING
Tips For Best Trimming Results
1. The very tip of the trimming line is the most
powerful in cutting, so allow the line tip to do
the cutting job.
2. Trim only when grass and weeds are dry.
3. The correct angle for the cutting attachment
is parallel to the ground.
4. Grass over 8 inch should be cut by working
from top to the bottom in small increments to
avoid premature line wear or motor drag.
(Fig. XIII)
5. Whenever possible, cut right to left. When
cutting to the left, the units cutting efficiency
is improved slightly. Also, the clippings are
thrown away from the operator.
6. Slowly move the trimmer into and out of the
area being cut, maintaining the trimmer at
the desired cutting height. This can be either
a side-to-side or forward-backward motion.
Cutting shorter lengths produces best
results.
Fig. XIII
F-041554C
14
MAINTENANCE AND SERVICE
WARNING: Always stop and
unplug the unit before performing ANY
maintenance.
WARNING: Always use genuine
factory replacement parts.
Before Each Use Check For Damaged/Worn
Parts
• Cutting Head Replace Cutting Head parts
that are bent, warped, cracked, or damaged
in any way.
• Extension Cord Look closely for
deterioration, cuts or cracks in the
insulation. Also inspect the connections for
damage. Replace the cord if any defects or
damage appear.
After Each Use Clean Unit And Labels
• Clean the unit using a damp cloth.
• Wipe off the unit with a clean, dry, soft cloth.
Replacing Inner Spool Assembly
1. Depress the two latches on the ends of
spool cap to remove the spool cap from the
unit. (Fig. XIV)
2. Remove the old inner spool assembly. (Fig.
XV)
3. Use a clean cloth to clean the inner surface
of the outer cap and the cutting head base.
4. Insert the end of the line of the new inner
spool assembly through the eyelet in the
cutting head base. (Fig. XV)
5. Hold the inner spool in place; grasp the line
end and pull firmly to release the line.
6. Replace the spool cap by pressing it till the
latches are locked.
WARNING: Make sure the cutting
head assembly is installed correctly
before connecting power to the trimmer.
Service Of Double Insulated Units
This unit is double-insulated. In a double-
insulated unit, two systems of insulation are
provided instead of grounding. No means of
grounding are provided on a double-insulated
unit, nor should a means for grounding be
added to this unit.
Servicing a double-insulated unit requires
extreme care and knowledge of the system, and
should be done only by qualified service
personnel. Replacement parts for a double-
insulated unit must be identical to the parts they
replace. A double-insulated unit is marked with
the words DOUBLE INSULATION or DOUBLE
INSULATED or symbol .
Fig. XIV
Fig. XV
F-041554C
MAINTENANCE AND SERVICE
15
Replacing The Cutting Line
WARNING: Always use genuine 0.065
inch nylon replacement line. Using line
other than specified may cause the unit
to overheat or fail.
WARNING: Never use metal–reinforced
line, wire, or rope, etc. These can break
off and become a dangerous projectile.
1. Remove the cutting head assembly and remove
inner spool set from the outer cap. (See step
1–3 in “Replacing Inner Spool Assembly”)
2. Remove the semi–transparent plastic line cover.
3. Remove the existing line.
4. Take approximately 12 feet of new trimming line.
5. Insert one end of the line into one hole on the
inner spool from inside to outside, then into the
other hole from outside to inside. (Figure 11)
Figure 11
6. Wind the line, in even and tight layers, in the
direction indicated on the inner spool.
(Figure 11)
7. Insert the end of the line into one hole on the
semi–transparent plastic line cover.
8. Replace the line cover. So the inner spool
assembly is set.
9. Re–assemble the inner spool assembly onto the
trimmer. (See Step 4–6 in “Replacing An Inner
Spool Assembly”)
CLEANING AND STORAGE
Clean And Store The Unit
1. Stop and unplug the trimmer.
2. Clean the unit using a damp cloth with a mild
detergent.
3. Wipe off the unit with a clean, dry, soft cloth.
4. Store the trimmer in a dry, well–ventilated area,
out of the reach of children and other
unauthorized users.
WARNING: Do not use any strong deter-
gents on the plastic housing or the han-
dle. They can be damaged by certain
aromatic oils such as pine and lemon,
and by solvents such as kerosene.
Moisture can also cause a shock haz-
ard. Wipe off any moisture with a soft
dry cloth.
F-041554C
16
TROUBLESHOOTING
PROBLEM
CAUSE
ACTION
Power connection not right
Check the extension cord and trimmer
cord plug-in and connection
Crowding cutting line
against material being cut
Allow tip of line to do the cutting
Cutting line bound with
grass
Stop the unit, unplug and clean the cutting
attachment
Crowding cutting line
against material being cut
Allow tip of line to do the cutting
Incorrect line size
Replace the Cutting line (See "Replacing
Cutting Line" in Maintenance Section)
Incorrect spool
Replace the inner spool assembly (See
"Replacing Spool Assembly" in
Maintenance Section)
Cutting head dirty
Stop the unit, unplug and remove the
cutting head to clean
Not enough line exposed
Stop the unit, unplug and pull the line by
hand with force (See "Adjusting Cutting
Line" in Assembly Section)
Cutting line bound with
grass
Stop the unit, unplug and clean the cutting
attachment
Cutting head out of line
Replace the inner spool assembly (See
"Replacing Inner Spool Assembly" in
Maintenance Section)
Incorrect line size
Replace the Cutting line (See "Replacing
Cutting Line" in Maintenance Section)
Inner spool bound up
Replace the inner spool assembly (See
"Replacing Spool Assembly" in
Maintenance Section)
Incorrect line size
Replace the Cutting line (See "Replacing
Cutting Line" in Maintenance Section)
Inner spool assembly worn
or damaged
Replace the inner spool assembly (See
"Replacing Inner Spool Assembly" in
Maintenance Section)
If further assistance is required, call 1-800-251-8007.
Motor will not operate
Cutting head will not
advance line
Line is released too fast
Line welds onto spool
F-041554C
17
ACCESSORIES AND REPLACEMENT PARTS
Part Part Number
Shield for 12 Inch Unit 776901
2
Shield for 15 Inch Unit 776901
1
Spool Assembly 770103
6
Assist Handle for 12 Inch Unit 776902
4
Assist Handle for 15 Inch Unit 776902
5
Guide Wheel 776901
4
Spool Cover 776908
5
Spring 776908
6
F-041554C
18
NOTES
F-041554C
MODE DEMPLOI
Tondeuse électrique à fil
Modèle
HTE381201 HTE461501
Ce manuel contient des informations importantes sur :
LA SÉCURITÉ, LASSEMBLAGE, LUTILISATION ET LENTRETIEN.
Veuillez lire et conserver ce manuel pour référence ultérieure.
Inscrivez les renseignements suivants sur cet appareil. Ces renseignements
sont nécessaires lors de la commande de pièces détachées ou en cas de perte
ou de vol.
Numéro de série :
F-041554C
TABLE DES MATIÈRES
2
F–041554C
GARANTIE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INFORMATIONS POUR L’UTILISATEUR 3. . . . . . . . . .
RESPONSABILITÉ DE L’UTILISATEUR 3. . . . . . . . . . . . .
CONSIGNES DE SÉCURITÉ IMPORTANTES 3. . . . . . .
SYMBOLES INTERNATIONAUX 6. . . . . . . . . . . . . . . . . .
CONTENU DU CARTON D’EMBALLAGE 7. . . . . . . . . .
CONNAISSANCE DE L’OUTIL 8. . . . . . . . . . . . . . . . . . . .
MONTAGE 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UTILISATION 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENTRETIEN ET RÉPARATION 12. . . . . . . . . . . . . . . . . . .
NETTOYAGE ET REMISAGE 13. . . . . . . . . . . . . . . . . . . . .
DÉPANNAGE 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSOIRES ET PIÈCES DE RECHANGE 14. . . . . . . .
REMARQUES 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Murray, Inc. garantit à l’acheteur initial que cet appareil sera exempt de défauts de matériaux et de fabrica-
tion dans des conditions normales d’utilisation et de fonctionnement pendant une période de deux (2) ans
à partir de la date d’achat. Conformément aux modalités et conditions indiquées dans cette garantie limi-
tée, nous réparerons ou remplacerons, à notre choix, sans frais pour l’acheteur initial toute pièce couverte
par cette garantie limitée pendant la période de garantie applicable.
La garantie ne couvre pas les pièces dont l’usure est normale. Les pièces dont l’usure est normale sont
définies comme étant les pièces et accessoires de coupe, y compris les lames, filins, chapeaux de ressort,
couvre–bobine intérieur et extérieur. Ces pièces sont garanties contre les défauts de matériaux et de fabri-
cation dans l’état où elles sont livrées avec le produit.
Cette garantie limitée de deux (2) ans de Murray, Inc., représente votre seul recours. Néanmoins, cette
garantie est nulle et non avenue pour les appareils qui ont été altérés, utilisés de façon abusive, mal utili-
sés ou utilisés à des fins de location ou d’autres fins commerciales et/ou professionnelles (des fins non
domestiques et lucratives). Votre garantie ne couvre pas les réglages mécaniques mineurs, qui ne sont
pas dus à des défauts de matériaux ou de fabrication. Pour toute assistance dans l’exécution de ces régla-
ges, consultez votre mode d’emploi.
Pour faire une demande de réparation dans le cadre de cette garantie limitée de deux (2) ans de Murray,
Inc., veuillez nous appeler au 1–800–251–8007(US), 1–800–661–6662 (Canada).
Cette garantie limitée de deux (2) ans de Murray, Inc., vous confère des droits juridiques précis et vous
pouvez également avoir d’autres droits, qui varient d’un état à un autre ou d’une province à une autre.
Cette garantie limitée remplace toute autre garantie explicite ou implicite, y compris la garantie implicite
de valeur marchande et la garantie d’aptitude à une fin particulière. Si vous avez besoin de plus de rensei-
gnements sur cette garantie écrite ou d’assistance pour l’obtention de service, écrivez–nous ou appelez–
nous à visitez–nous à : www.murray.com.
GARANTIE MURRAY, INC. LIMITÉE DE DEUX ANS
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/