Vega VEGAPULS C 21 Product information

Brand: Vega

Model: VEGAPULS C 21

Category: Measuring, testing & control

Type: Product information

This manual is also suitable for

Product information

Radar

Level measurement in liquids and bulk solids

VEGAPULS C 11

VEGAPULS C 21

VEGAPULS C 22

VEGAPULS C 23

VEGAPULS 11

VEGAPULS 21

VEGAPULS 31

Document ID: 58365

Contents

Radar

58365-US-210330

Contents

1 Measuring principle ............................................................................................................................................................................................... 3

2 Type overview ......................................................................................................................................................................................................... 4

3 Instrument selection .............................................................................................................................................................................................. 6

4 Mounting ................................................................................................................................................................................................................. 7

5 Electronics - Two-wire 4 … 20 mA ........................................................................................................................................................................ 9

6 Electronics - Two-wire 4 … 20 mA/HART ........................................................................................................................................................... 10

7 Electronics - SDI-12 .............................................................................................................................................................................................11

8 Electronics - Modbus ...........................................................................................................................................................................................12

9 Adjustment ........................................................................................................................................................................................................... 13

10 Dimensions ...........................................................................................................................................................................................................14

Take note of safety instructions for Ex applications

Please note the Ex specic safety information that you can nd at www.vega.com and that comes with each instrument. In hazardous areas you

should take note of the appropriate regulations, conformity and type approval certicates of the sensors and power supply units. The sensors must

only be operated on intrinsically safe circuits. The permissible electrical values are stated in the certicate.

Measuring principle

Radar

58365-US-210330

1 Measuring principle

Measuring principle

The devices emit a continuous radar signal through their antennas. The

emitted signal is reected by the medium and received as an echo by the

antenna.

The frequency dierence between the emitted and received signal is pro-

portional to the distance and depends on the lling height. The determined

lling height is converted into a respective output signal and output as

measured value.

80 GHz technology

The 80 GHz technology used enables a unique focusing of the radar beam

and a wide dynamic range of the radar sensors. The greater the dynamic

range of a radar sensor, the wider its application spectrum and the higher

its measurement reliability.

Advantages

Non-contact radar technology is characterized by extremely high mea-

surement accuracy. The measurement is inuenced neither by uctuating

product features nor by changing process conditions such as temperature,

pressure or strong dust generation. The user-friendly adjustment without

vessel lling and emptying saves time.

Input variable

The measured variable is the distance between the antenna edge of the

sensor and the medium surface. The antenna edge is also the reference

plane for the measurement.

Fig. 1: Data of the input variable

1 Reference plane

2 Measured variable, max. measuring range

Type overview

Radar

58365-US-210330

2 Type overview

VEGAPULS C 11 VEGAPULS C 21 VEGAPULS C 22

Applications Water processing, pump stations, storm wa-

ter overow tank, level monitoring

Water processing, pump stations, storm

water overow tank, ow measurement in

open umes, level monitoring

Water processing, pump stations, storm

water overow tank, ow measurement in

open umes, level monitoring

Max. measuring range 8 m (26.25 ft) 15 m (49.21 ft) 15 m (49.21 ft)

Antenna/Material Integrated antenna system/PVDF encap-

sulated

Integrated antenna system/PVDF encap-

sulated

Integrated antenna system/PVDF encap-

sulated

Beam angle 8° 8° 8°

Process tting/Material G1½, 1½ NPT, R1½/PVDF G1½, 1½ NPT, R1½ G1½, 1½ NPT, R1½

Connection for mounting

strap

G1, 1 NPT, R1 G1, 1 NPT, R1 G1½, 1½ NPT, R1½

Process temperature -40 … +60 °C

-40 … +140 °F)

-40 … +80 °C

(-40 … +176 °F)

-40 … +80 °C

(-40 … +176 °F)

Process pressure -1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

Deviation ≤ 5 mm ≤ 2 mm ≤ 2 mm

Frequency range W-band W-band W-band

Signal output

•

Two-wire 4 … 20 mA

•

Two-wire 4 … 20 mA/HART

•

SDI-12

•

Modbus

•

Two-wire 4 … 20 mA/HART

•

SDI-12

•

Modbus

Communication interface Bluetooth Bluetooth Bluetooth

Indication/Adjustment -/Via app on smartphone or tablet and Blue-

tooth

-/Via app on smartphone or tablet and Blue-

tooth

-/Via app on smartphone or tablet and Blue-

tooth

Approvals

•

c-UL-us, EAC, RCM

•

ATEX/IEC

•

EAC/SEPRO

•

NEPSI/CCOE/TIIS/KOSHA

•

INMETRO/IA

•

c-UL-us, EAC, RCM

•

ATEX/IEC

•

EAC/SEPRO

•

NEPSI/CCOE/TIIS/KOSHA

•

INMETRO/IA

Available or applied for

Type overview

Radar

58365-US-210330

VEGAPULS C 23 VEGAPULS 11 VEGAPULS 21 VEGAPULS 31

Water processing, pump stations, storm

water overow tank, ow measurement

in open umes, level monitoring

Water treatment, storage tanks in all

industrial areas, plastic tanks (measure-

ment through the tank wall)

Water treatment, storage tanks in all

industrial areas, plastic tanks (measure-

ment through the tank wall)

Water treatment, storage tanks in all

industrial areas, plastic tanks (measure-

ment through the tank wall)

30 m (98.43 ft) 8 m (26.25 ft) 15 m (49.21 ft) 15 m (49.21 ft)

Integrated antenna system/PVDF en-

capsulated

Integrated antenna system/PVDF en-

capsulated

Integrated antenna system/PVDF en-

capsulated

Integrated antenna system/PVDF en-

capsulated

4° 8° 8° 8°

- G1½, 1½ NPT, R1½ G1½, 1½ NPT, R1½ G1½, 1½ NPT, R1½

G1, 1 NPT, R1 G1½, 1½ NPT, R1½ G1½, 1½ NPT, R1½ G1½, 1½ NPT, R1½

-40 … +80 °C

(-40 … +176 °F)

-40 … +60 °C

-40 … +140 °F)

-40 … +80 °C

(-40 … +176 °F)

-40 … +80 °C

(-40 … +176 °F)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

-1 … +3 bar/-100 … +300 kPa

(-14.5 … +43.51 psi)

≤ 2 mm ≤ 5 mm ≤ 2 mm ≤ 2 mm

W-band W-band W-band W-band

•

Two-wire 4 … 20 mA/HART

•

SDI-12

•

Modbus

•

Two-wire 4 … 20 mA

•

Two-wire 4 … 20 mA/HART

•

Two-wire 4 … 20 mA/HART

Bluetooth Bluetooth Bluetooth Bluetooth

-/Via app on smartphone or tablet and

Bluetooth

-/Via app on smartphone or tablet and

Bluetooth

-/Via app on smartphone or tablet and

Bluetooth

Integrated display and adjustment unit/

Via app on smartphone or tablet and

Bluetooth

•

c-UL-us, EAC, RCM

•

ATEX/IEC

•

EAC/SEPRO

•

NEPSI/CCOE/TIIS/KOSHA

•

INMETRO/IA

•

c-UL-us, EAC, RCM

•

ATEX/IEC

•

EAC/SEPRO

•

NEPSI/CCOE/TIIS/KOSHA

•

INMETRO/IA

•

c-UL-us, EAC, RCM

•

ATEX/IEC

•

EAC/SEPRO

•

NEPSI/CCOE/TIIS/KOSHA

•

INMETRO/IA

Instrument selection

Radar

58365-US-210330

3 Instrument selection

Application area

The radar sensors of the VEGAPULS 10, 20, 30 series described here are

used for non-contact level measurement of liquids and bulk solids. They can

be used in both simple and aggressive liquids. The sensors also measure

light and heavy bulk solids absolutely reliably, both with strong dust and

noise generation and independent of buildup or condensation.

Device overview

VEGAPULS C 11

VEGAPULS C 11 is the ideal sensor for non-contact level measurement in

simple applications where a high degree of protection is required. It is par-

ticularly suitable for use in water treatment, pumping stations, rain overow

basins and level monitoring.

VEGAPULS C 21, C 22, C 23

VEGAPULS C 21, C 22, C 23 are the ideal sensors for non-contact level

measurement in simple applications where a high degree of protection is

required. They are particularly suitable for use in water treatment, pumping

stations and rain overow basins, for ow measurement in open channels

and level monitoring.

VEGAPULS 11, 21, 31

VEGAPULS 11, 21, 31 are the ideal sensors for non-contact level mea-

surement in simple applications. They are particularly suitable for use in

water treatment, storage tanks with acids, lyes and additives in all industrial

areas, or for measuring levels in plastic tanks from the outside through the

tank wall.

Conguration and housing protection classes

The radar sensors of series VEGAPULS 10, 20, 30 are available in dierent

designs, housing protection classes and connection techniques. The follow-

ing illustrations show typical examples.

Fig. 2: VEGAPULS C 11 with direct cable outlet in protection rating IP66/IP68 (3 bar)

1 Radar antenna

2 Processtting

3 Electronics housing

4 Mounting thread

5 Connection cable

Fig. 3: VEGAPULS C 22 with direct cable outlet for ceil mounting in protection rating

IP66/IP68 (3 bar)

1 Radar antenna

2 Processtting

3 Electronics housing

4 Cable outlet

Fig. 4: VEGAPULS C 23 with direct cable outlet in protection rating IP66/IP68 (3 bar)

1 Radar antenna

2 Electronics housing

3 Mounting thread

4 Connection cable

Fig. 5: VEGAPULS 31 in protection class IP66/IP67

1 Radar antenna

2 Processtting

3 Process seal

4 Electronics housing

5 Display and adjustment unit

6 Ventilation/pressure compensation

Mounting

Radar

58365-US-210330

4 Mounting

Installation position

Mount the sensor in a position which is at least 200 mm (7.874 in) away

from the vessel wall. If the sensor is installed in the center of dished or

round vessel tops, multiple echoes can arise. However, these can be sup-

pressed by an appropriate adjustment.

> 200 mm

(7.87

Fig. 6: Mounting of the radar sensor on round vessel tops

In vessels with conical bottom it can be advantageous to mount the sensor

in the centre of the vessel, as measurement is then possible down to the

bottom.

Fig. 7: Mounting of the radar sensor on vessels with conical bottom

Mounting examples gauge measurement

The following illustrations show mounting examples and possible measure-

ment setups.

River level

Fig. 8: Gauge measurement river, sensor mounting on bridge pier

Deep well level

Fig. 9: Gauge measurement deep well, sensor mounting on lid

Mounting examples ow measurement

The following illustrations show mounting examples and possible measure-

ment setups.

Rectangular overfall

3 ... 4 h

max

90°

max

≥ 2 x h

max

90°

42 3

≥ 250 mm

(

9.84")

≥ 250 mm

(

9.84")

Fig.10:Flowmeasurementwithrectangularume:h

max.

=max.llingoftherectangular

ume

1 Overfallorice(sideview)

2 Upstream water

3 Tailwater

4 Overfallorice(viewfromtailwater)

Mounting

Radar

58365-US-210330

Khafagi-Venturi ume

3 ... 4 x h

max

90°

max

≥ 250 mm

(

9.84")

Fig.11:FlowmeasurementwithKhafagi-Venturiume:h

max.

=max.llingoftheume;

B=tightestconstrictionintheume

1 Position sensor

2 Venturiume

Electronics - Two-wire 4 … 20 mA

Radar

58365-US-210330

5 Electronics - Two-wire 4 … 20 mA

Voltage supply

Power the instrument via an energy-limited circuit (power max. 100 W) acc.

to IEC 61010-1.

Specications of the voltage supply:

•

Operating voltage

– 12 … 35 V DC

•

Permissible residual ripple

– for U

12 V DC (12 V < U

< 18 V): ≤ 0,7 V

e

(16 … 400 Hz)

– for U

24 V DC (18 V < U

< 35 V): ≤ 1,0 V

e

(16 … 400 Hz)

Keep in mind the following additional factors that inuence the operating

voltage:

•

Lower output voltage of the power supply unit under nominal load (e.g.

with a sensor current of 20.5 mA or 22 mA in case of fault)

•

Inuence of additional instruments in the circuit (see load values in

chapter " Technical data" of the operating instructions of the respective

instrument)

Connection cable

The instrument is connected with standard two-wire cable.

Connection

Direct cable outlet

Fig. 12: Wire assignment in permanently connected connection cable

Wire colour Function Polarity

1 Brown Voltage supply, signal output +

2 Blue Voltage supply, signal output -

Connection housing

(+)1 2(-)

Fig. 13: Connection compartment VEGAPULS

1 Voltage supply, signal output

Electronics - Two-wire 4 … 20 mA/HART

Radar

58365-US-210330

6 Electronics - Two-wire 4 … 20 mA/HART

Voltage supply

Power the instrument via an energy-limited circuit (power max. 100 W) acc.

to IEC 61010-1.

Specications of the voltage supply:

•

Operating voltage

– 12 … 35 V DC

•

Permissible residual ripple

– for U

12 V DC (12 V < U

< 18 V): ≤ 0,7 V

e

(16 … 400 Hz)

– for U

24 V DC (18 V < U

< 35 V): ≤ 1,0 V

e

(16 … 400 Hz)

Keep in mind the following additional factors that inuence the operating

voltage:

•

Lower output voltage of the power supply unit under nominal load (e.g.

with a sensor current of 20.5 mA or 22 mA in case of fault)

•

Inuence of additional instruments in the circuit (see load values in

chapter " Technical data" of the operating instructions of the respective

instrument)

Connection cable

The instrument is connected with standard two-wire cable. If electromag-

netic interference is expected which is above the test values of EN 61326-1

for industrial areas, shielded cable should be used.

Shielded cable generally necessary in HART multidrop mode.

Connection

Direct cable outlet

Fig. 14: Wire assignment in permanently connected connection cable

Wire colour Function Polarity

1 Brown Voltage supply, signal output +

2 Blue Voltage supply, signal output -

3 Shielding

Connection housing

(+)1 2(-)

Fig. 15: Connection compartment VEGAPULS

1 Voltage supply, signal output

2 Plug connector for display and adjustment unit

Electronics - SDI-12

Radar

58365-US-210330

7 Electronics - SDI-12

Voltage supply

The device is supplied with power via an SDI-12 datalogger.

Power the instrument via an energy-limited circuit (power max. 100 W) acc.

to IEC 61010-1.

Specications of the voltage supply:

•

Operating voltage

– 9 … 32 V DC

•

max. number of sensors

– 32

Connection cable

The instrument is connected with standard three-wire cable without shield-

ing. If electromagnetic interference is expected which is above the test

values of EN 61326-1 for industrial areas, shielded cable should be used.

Connection

Direct cable outlet

Fig. 16: Wire assignment in permanently connected connection cable

Wire colour Function Polarity

1 Brown Voltage supply +

2 Blue Voltage supply -

3 White SDI Data +

4 Shielding

Electronics - Modbus

Radar

58365-US-210330

8 Electronics - Modbus

Voltage supply

The operating voltage and the digital bus signal are routed via separate

two-wire connection cables.

Power the instrument via an energy-limited circuit (power max. 100 W) acc.

to IEC 61010-1.

Specications of the voltage supply:

•

Operating voltage

– 8 … 30 V DC

•

max. number of sensors

– 32

Connection cable

The instrument is connected with standard two-wire, twisted cable suitable

for RS 485. If electromagnetic interference is expected which is above the

test values of EN 61326 for industrial areas, shielded cable should be used.

Make sure that the entire installation is carried out according to the Fieldbus

specication. In particular, make sure that the bus is terminated with suit-

able terminating resistors.

Connection

Direct cable outlet

Fig. 17: Wire assignment in permanently connected connection cable

Wire colour Function Polarity

1 Brown Voltage supply +

2 Blue Voltage supply -

3 Black Modbus signal D0 +

4 White Modbus signal D1 -

5 Shielding

Adjustment

Radar

58365-US-210330

9 Adjustment

9.1 Wireless adjustment

Devices with integrated Bluetooth module can be adjusted wirelessly via

standard adjustment tools:

•

Smartphone/tablet (iOS or Android operating system)

•

PC/notebook (Windows operating system)

Fig. 18: Wireless connection to standard operating devices with integrated Blue-

tooth LE

1 Sensor

2 Smartphone/Tablet

3 PC/Notebook

9.2 Adjustment via the signal cable

Devices with signal output 4 … 20 mA/HART can also be operated via a

signal cable. This is done via an interface adapter and a PC/notebook using

DTM/PACTware.

2 4

OPEN

TWIST

USB

LOCK

Fig. 19: Connecting the PC to the signal cable

1 Sensor

2 HARTresistance250Ω(optionaldependingonevaluation)

3 Connection cable with 2 mm pins and terminals

4 Voltage supply

5 Interface adapter VEGACONNECT

9.3 Local adjustment

The integrated display and adjustment unit is used for on-site adjustment of

VEGAPULS 31

Fig. 20: Integrated display and adjustment unit

1 LC display

2 Adjustment keys

Dimensions

Radar

58365-US-210330

10 Dimensions

VEGAPULS C 11, C 21

1 2 3

ø 68 mm

(2.68")

ø 6 mm

(0.24")

SW 41

ø 76 mm

(2.99")

G1½

G1; 1NPT

1½ - 14 NPT

R 1½

23 mm

(0.92")

29 mm

(1.14")

109 mm

(4.28")

Fig. 21: Dimensions VEGAPULS C 11, C 21

1 Thread G1½

2 Thread 1½ NPT

3 Thread R1½

VEGAPULS C 22

23 mm

(0.91")

57 mm

(2.24")

ø 6 mm

(0.24")

G1½

ø 58 mm

(2.28")

64 mm

(2.52")

1½ - 14 NPT R 1½

79 mm

(3.11")

1 2 3

Fig. 22: Dimensions VEGAPULS C 22

1 Thread G1½

2 Thread 1½ NPT

3 Thread R1½

VEGAPULS C 23

29 mm

(1.14")

130 mm

(5.13")

ø 76 mm

(2.99")

G1;

1 NPT; R1

ø 6 mm

(0.24")

SW 41

Fig. 23: Dimensions VEGAPULS C 23

1 Thread G1½

2 Thread 1½ NPT

3 Thread R1½

VEGAPULS 11, 21, 31

50 mm

(1.97")

122 mm

(4.80")

25 mm

(0.98")

G1½

SW 50

ø 58 mm

(2.28")

ø 77,5 mm

(3.05")

1½ - 14 NPT R 1½

156 mm

(6.14")

1 2 3

Fig. 24: Dimensions VEGAPULS 11, 21, 31

1 Thread G1½

2 Thread 1½ NPT

3 Thread R1½

Mounting strap for ceiling mounting

1 2

86 mm

(3.39")

65 mm

(2.56")

ø 31,4 mm

(1.24")

10 mm

(0.39")

49 mm

(1.93")

14,5 mm

(0.57")

ø 8 mm

(0.31")

66,7 mm

(2.63")

81,3 mm

(3.2")

40 mm

(1.57")

16,1 mm

(0.63")

8 mm

(0.31")

2 mm

(0.08")

36,1 mm

(1.42")

Fig. 25: Mounting strap for ceiling mounting

1 Sensor holder 1"

2 Sensor holder 1½"

Mounting strap for wall mounting - bracket 200 mm

433 mm

(17.05")

10 mm

(0.39")

ø 34,1 mm

(1.34")

ø 49 mm

(1.93")

128 mm

(5.04")

65 mm

(2.56")

ø 10,5 mm

(0.41")

ø 10,5 mm

(0.41")

14,5 mm

(0.57")

8 mm

(0.31")

63 mm

(2.48")

2 mm

(0.08")

23 mm

(0.91")

18 mm

(0.71")

9,5 mm

(0.37")

SW 5

Fig. 26: Mounting strap for wall mounting - bracket 200 mm

1 Sensor holder 1"

2 Sensor holder 1½"

The listed drawings represent only an excerpt of the available ver-

sions and mounting possibilities. You can nd more drawings at

www.vega.com/downloads under " Drawings".

Notes

Radar

58365-US-210330

VEGA Grieshaber KG

Am Hohenstein 113

77761 Schiltach

Germany

58365-US-210330

All statements concerning scope of delivery, application, practical use and operating conditions of the sensors and processing systems correspond to the information available

at the time of printing.

Subject to change without prior notice

Phone +49 7836 50-0

E-mail: [email protected]

www.vega.com