Extron PMK 300 User manual

Extron
Brand
Extron
Model
PMK 300
Category
Projector accessories
Type
User manual

This manual is also suitable for

Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
68-993-01
Rev. B 12 05
PMK 300 Multi-Product Projector Mounting Kit
Installation Instructions
N Only VersaTools products and most IP Link products can be
mounted using the multi-product projector mounting kit.
1. If necessary, remove the feet from the bottom of the device to be
installed.
2. Mount the device(s) to any of the bracket’s three mounting
plates. The device(s) can be vertically mounted facing either
up or down, whichever is most convenient. See fi gure 1 on the
other side of this card.
N On the side mounting plates, the device is typically mounted on
the outside of the bracket.
On the front mounting plate, the device is typically mounted on
the inside of the bracket.
a. For a VersaTools or IP Link device, use two supplied
4-40 x 3/16 screws in opposite (diagonal) corners to
secure the device to the bracket.
b. For a power supply, use the two included tie wraps to
strap the power supply to the bracket.
N The PMK 300 has a hole in the bottom plate that allows the
projector pole to be inserted through the center of the plate
rather than outside of the plate (see fi gure 2 on the other side of
this card). To install the PMK 300 in this confi guraion, slide
the bracket up from the bottom of the pole before the projector is
installed on the pole.
3. Affi x the supplied rubber pad to the side of the U-bolt clamping
plate that the projector pole contacts.
4. Place the U-bolt around the ceiling pole and insert the two legs
of the U-bolt through the slotted holes on the bracket’s clamping
plate and then through the round holes on the backing brace.
For a typical (1.5“ to 2.0“ diameter) pole — The supplied U-bolt
fi ts a typical ceiling pole.
For a smaller or larger pole — Locally obtain a U-bolt that fi ts
the ceiling pole. The slotted holes on the bracket can accomodate
a U-bolt for pole sizes from 1.0“ to 2.5“ in diameter.
5. Secure the bracket to the U-bolt with the included hex nuts,
washers, and lock washers. Use a proper-sized socket to tighten
the hex nuts.
PMK 300 Multi-Product Projector Mounting Kit
Installation Instructions (continued)
Extron
PMK 300
Multi Product Projector
Mount Kit
U-Bolt
Rubber Pad
Backing
Brace
Clamping
Plate
U-Bolt
Extron
PMK 300
Multi Product Projector
Mount Kit
Rubber Pad
Clamping
Plate
Backing
Brace
Figure 1 Figure 2
  • Page 1 1

Extron PMK 300 User manual

Extron
Brand
Extron
Model
PMK 300
Category
Projector accessories
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents