Fujitsu TFT 463VFA User manual

Brand: Fujitsu

Model: TFT 463VFA

Category: TVs & monitors

Type: User manual

This manual is also suitable for

463V FA

Page is loading ...

Sie haben ...

... technische Fragen oder Probleme?

Wenden Sie sich bitte an

unseren Help Desk (siehe Garantieheft).

Aktuelle Informationen zu unseren Produkten, Tipps, Updates usw. finden Sie im Internet:

http://www.fujitsu-siemens.com

Are there ...

... any technical problems or other

questions you need clarified?

Please contact

our Help Desk (see Warranty Booklet).

The latest information on our products, tips, updates, etc., can be found on the Internet under:

http://www.fujitsu-siemens.com

Page is loading ...

Dieses Handbuch wurde auf Recycling-Papier gedruckt.

This manual has been printed on recycled paper.

Ce manuel est imprimé sur du papier recyclé.

Este manual ha sido impreso sobre papel reciclado.

Questo manuale è stato stampato su carta da riciclaggio.

Denna handbok är tryckt på recyclingpapper.

Dit handboek werd op recycling-papier gedrukt.

Herausgegeben von/Published by

Fujitsu Siemens Computers GmbH

Bestell-Nr./Order No.:

A26361-K864-Z100-1-5E19

Printed in Taiwan

AG 0502 05/02

636

1-K

4-Z1

-1-

463V FA

BETRIEBSANLEITUNG

OPERATING MANUAL

463V FA

LCD-Bildschirm

LCD monitor

Betriebsanleitung

Operating Manual

Deutsch

English

Ausgabe Mai 2002

May 2002 edition

VESA, DDC und DPMS sind eingetragene Warenzeichen der Video Electronics Standards

Association.

Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren.

Zuwiderhandlungen verpflichten zu Schadenersatz.

Liefermöglichkeiten und technische Änderungen vorbehalten.

Dieses Handbuch wurde erstellt von

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

VESA, DDC and DPMS are registered trademarks of Video Electronics Standards

Association.

All rights, including rights of translation, reproduction by printing, copying or similar methods,

even of parts are reserved.

Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model or design,

are reserved.

Delivery subject to availability. Right of technical modification reserved.

This manual was produced by

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

A26361-K864-Z100-1-5E19 English

Contents

Introduction........................................................................................................................................1

Notational conventions ..............................................................................................................2

Important notes..................................................................................................................................2

Safety........................................................................................................................................2

Cleaning ....................................................................................................................................3

Transport...................................................................................................................................3

Energy Star Guidelines..............................................................................................................4

CE marking................................................................................................................................4

FCC Class B Compliance Statement.........................................................................................4

Declaration of Conformity ..........................................................................................................5

Power cable...............................................................................................................................5

Disposal and recycling...............................................................................................................6

Checking the contents of the consignment ........................................................................................6

Installing an ergonomic video workstation..........................................................................................7

Connecting the monitor......................................................................................................................7

Connecting cables to the monitor...............................................................................................8

Connecting cables to the computer............................................................................................9

Operation of the monitor....................................................................................................................9

Adjusting rake and rotation........................................................................................................9

Switching the monitor on/off.....................................................................................................10

Notes on power management..................................................................................................10

Changing the monitor settings .................................................................................................11

Notes on ergonomic colour adjustment............................................................................................17

Removing the monitor base.............................................................................................................18

Technical data.................................................................................................................................18

VESA-DDC-compatible VGA interface.....................................................................................19

Preset operating modes...........................................................................................................20

Pin assignment D-SUB............................................................................................................20

Monitor port DVI-D...................................................................................................................21

Trouble shooting..............................................................................................................................21

Page is loading ...

A26361-K864-Z100-1-5E19 English - 1

Introduction

Your new LCD (Liquid Crystal Display) monitor 463V FA offers numerous features and functions, for

example:

· TFT display (Thin Film Transistor; active matrix)

· minimal space requirements thanks to slim casing

· optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour

purity right into the corners)

· high degree of brightness and good contrast

· high resolution (1280x1024) for displaying the information content of a conventional 21-inch

screen with CRT (Cathode Ray Tube)

· presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)

· automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical

frequencies) from 56 to 76 Hz (absolutely flicker-free)

· digital screen controller with microprocessor for storing 26 different display modes

· freely adjustable colour alignment for matching the screen colours to the colours of various

input and output devices

· convenient operation via integrated OSD (On-Screen-Display) menu

· VESA-DDC compatibility

· VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) - mechanical

interface to swivel arm and wall bracket)

· plug&play capability

· power management for reducing power consumption when the computer is not in use

· compliance with the recommendations in accordance with TCO ’99

In normal screen mode (dark characters against a light background) the monitor satisfies the

ergonomic requirements for the GS symbol.

This Operating Manual contains important information you require to start up and run your LCD

monitor.

A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is

required to control the 463V FA LCD monitor. The monitor processes the data supplied to it by the

screen controller. The screen controller/the associated driver software is responsible for setting the

modes (resolution and refresh rate).

When putting the monitor into operation for the first time, the screen display should be optimally

adapted to the screen controller used and adjusted in accordance with your needs (see the

"Changing the monitor settings" section in the"Operation of the monitor" chapter).

Target group

You don't need to be an "expert" to perform the operations described here. Do, however, read the

chapter "Important notes" in the Operating Manual of the computer and in this Operating Manual.

In the event of any problems occurring, please contact your sales outlet or our Help Desk.

Further information

Details of how you set the resolution and refresh rate are provided in the documentation on your

screen controller/the associated driver software.

Colour monitor 463V FA

2 - English A26361-K864-Z100-1-5E19

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

Pay particular attention to text marked with this symbol. Failure to observe this warning

endangers your life, destroys the device, or may lead to loss of data.

Supplementary information, remarks, and tips follow this symbol.

Ê Text which follows this symbol describes activities that must be performed in the order shown.

"Quotation marks" indicate names of chapters or terms.

Texts in italics indicate filenames and menu items.

Important notes

In this chapter you will find information regarding safety which is essential to take note of

with your monitor.

Safety

This device complies with the relevant safety regulations for data processing equipment, including

electronic office machines for use in an office environment. If you have any questions, contact your

sales outlet or our Help Desk.

· The display surface of the LCD monitor is sensitive to pressure and scratches. You should

therefore be careful with the display surface so as to avoid lasting damage (Newton rings,

scratches).

· If the device is brought into the installation site from a cold environment, condensation can

form. Before operating the device, wait until it is absolutely dry and has reached approximately

the same temperature as the installation site.

· During installation and before operating the device, please observe the instructions on

environmental conditions in the "Technical data" chapter as well as the instructions in the

"Installing an ergonomic video workstation" chapter.

· To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never

be blocked.

· The power adapter automatically sets itself to a mains voltage in the range of 100 V to 240 V.

Ensure that the local mains voltage lies within these limits.

· Ensure that the power socket on the power adapter or the grounded mains outlet is freely

accessible.

· The ON/OFF switch does not disconnect the device from the mains voltage. To completely

disconnect the mains voltage, remove the power plug from the socket.

· Lay all cables so that nobody can stand on them or trip over them. When attaching the device,

observe the relevant notes in the chapter "Connecting the monitor".

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 3

· If you use a different data cable from the one supplied, ensure that it is adequately shielded.

CE conformance and optimum picture quality are guaranteed only if you use the data cable

supplied.

· No data transmission cable should be connected or disconnected during a thunderstorm.

· Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the

device (danger of electric shock, short circuit).

· In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign

matter), switch off the unit, disconnect the power plug and contact your sales outlet or our Help

Desk.

· The screen background lighting contains mercury. You must observe the applicable handling

and disposal safety regulations for fluorescent tubes.

· Only qualified technicians should repair the device. Unauthorised opening and incorrect repair

may greatly endanger the user (electric shock, fire risk).

· Only use the power adapter supplied or a power adapter of the same type: LSE9901B1260 (Li

Shin) or UP06041120A (Potrans).

· The power adapter may only be opened by authorised specialist personnel.

· You may set only those resolutions and refresh rates specified in the "Technical data" chapter.

Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or

our Help Desk.

· Keep this operating manual together with your device. If you pass on the device to third parties,

you should include this manual.

Cleaning

· Always pull out the power plug before you clean the monitor.

· Do not clean any interior parts yourself, leave this job to a service technician.

· Do not use any cleaning agents that contain abrasives or may corrode plastic.

· Ensure that no liquid will run into the system.

· Ensure that the ventilation areas of the monitor are free.

· The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only

using a soft, slightly moistened cloth.

Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has

been moistened in mild domestic detergent and then carefully wrung out.

Transport

· Transport the monitor with care and only in its original packaging or another corresponding

packaging fit to protect it against knocks and jolts.

· Never drop the LCD monitor (danger of glass breakage).

Colour monitor 463V FA

4 - English A26361-K864-Z100-1-5E19

Energy Star Guidelines

The Fujitsu Siemens LCD colour monitor 463V FA is designed to conserve

electricity by dropping to less than 3 W when it goes into standby,

suspend and OFF mode. With this new power management the 463V FA

qualifies for the U.S. Environmental Protection Agency's (EPA) Energy

Star Computers award.

The EPA estimates that computer equipment uses 5 percent of all business electricity and that this

is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in

use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings

could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the

equivalent of 5 million automobiles.

As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product

meets the Energy Star guidelines for energy efficiency.

CE marking

The shipped version of this device complies with the requirements of the EEC

directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage

directive".

FCC Class B Compliance Statement

The following statement applies to the products covered in this manual, unless otherwise specified

herein. The statement for other products will appear in the accompanying documentation.

NOTE:

This equipment has been tested and found to comply with the limits for a "Class B" digital device,

pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-

Causing Equipment Regulations. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in strict accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between equipment and the receiver.

· Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused

by unauthorized modifications of this equipment or the substitution or attachment of connecting

cables and equipment other than those specified by Fujitsu Siemens Computers GmbH The

correction of interference caused by such unauthorized modification, substitution or attachment will

be the responsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to any and all optional

peripheral or host devices. Failure to do so may violate FCC rules.

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 5

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Product Name: LCD Monitor

Trade Name: Fujitsu Siemens Computers

Model Number(s): 463V FA

Name of Responsible Party: Fujitsu Siemens Computers Inc.

598 Gibraltar Drive

Milpitas, CA 95035-6315

U.S.A.

Contact Person: Reiner Johannis

Phone No.: (408) 571-6051

Fax No.: (408) 571-6196

Power cable

To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary

to replace the original cable set.

· The female/male receptacles of the cord set must meet CEE-22 requirements.

· The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the

outer sheath or on the insulation of one of the inner conductors.

· For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.

For devices which sit on the floor, only SJT type cable sets may be used.

· The cable set must be selected according to the rated current for your device.

Power cable for devices distributed in the US and Canada

In the United States and Canada the cord set must also be UL-listed and CSA-labelled. The voltage

rating should be min. 250 volts a.c.

Please consult the following table for the selection criteria for power cables used in the United

States and Canada.

Cable type Size of conductors in cable Maximum current rating of the device

SJT 18 AWG

16 AWG

14 AWG

10 Amps

12 Amps

SVT 18 AWG

17 AWG

10 Amps

12 Amps

Colour monitor 463V FA

6 - English A26361-K864-Z100-1-5E19

Disposal and recycling

This device has been manufactured to the highest possible degree from materials which can be

recycled or disposed of in a manner that is not environmentally damaging. The device may be taken

back after use to be recycled, provided that it is returned in a condition that is the result of normal

use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.

If you have any questions on disposal, please contact your local office, our Help Desk, or:

Fujitsu Siemens Computers GmbH

Recyclingcenter

D-33106 Paderborn

Tel.: +49 5251 / 81 80 10, Fax: +49 5251 / 81 80 15

Checking the contents of the consignment

Ê Unpack all the individual parts.

Ê Check the delivery for damage incurred during transportation.

Ê Check whether the delivery agrees with the details in the delivery note.

The complete LCD monitor package includes:

- one monitor

- one data cable (D-SUB)

- one data cable (DVI-D)

- one power cable

- a power adapter with power adapter cable

- one floppy disk

- one Warranty Booklet

- this Operating Manual

Should you discover that the delivery does not correspond to the delivery note, notify your local

sales outlet immediately.

It is recommended not to throw away the original packaging material. Keep it for future

transportation.

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 7

Installing an ergonomic video workstation

Before you set up your equipment, you should select a suitable position for working at the monitor.

Please observe the following advice when installing a video workstation.

Window

permissible

reaching sector

600 mm

edge of desk

permissible

reaching sector

600 mm

Avoid direct and reflected glare. Avoid glare from electric

lighting.

Position the keyboard where it

is easiest to reach.

30°

65°

0°

60°

0°

permissible viewing sector

preferable viewing sector

permissible

viewing sector

approx. 90°

and more

approx. 90°

Position the monitor for

optimum viewing. The viewing

distance to the monitor should

be approximately 50 cm.

Keep ventilated areas clear. Remember to maintain correct

posture.

Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available

from specialised dealers, may be advisable. For this purpose the monitor base must be removed

beforehand as described in chapter "Removing the monitor base".

Connecting the monitor

Please note the information provided in the "Safety" section in the chapter "Important

notes" at the beginning of this manual.

CE conformance and optimum picture quality are guaranteed only if you use the data

cable supplied.

Do not cover the ventilation openings of the monitor.

The computer power plug must be pulled out!

Ê Be sure that the monitor and the computer are switched off.

Colour monitor 463V FA

8 - English A26361-K864-Z100-1-5E19

Connecting cables to the monitor

The monitor ports are protected by a cover.

2 3 4

1 = Cover

2 = Connector for the power supply

3 = D-SUB connector (ANALOG)

4 = DVI-D connector (DIGITAL)

Ê Remove the cover (1).

The data cables provided have plugs for the D-SUB connector or the DVI-D connector on the

monitor.

Ê Select the suitable data cable for your computer.

Digital graphics card with DVI interface: DVI connector

Graphics card with VGA interface: D-SUB connector

Information on the computer connections and interfaces is contained in the operating manual for

your computer.

Ê Connect one of the D-SUB connectors of the data cable to the D-SUB connector on the

monitor (3) and secure the plug-in connection by tightening the safety screws.

If you want to use the data cable with DVI-D connector or if you want to connect the

monitor to a second computer, proceed as follows:

Ê Connect the DVI-D connector of the data cable to the DVI-D connector on the

monitor (4) and secure the plug-in connection by tightening the safety screws.

After switching on the monitor you must select the desired input with the OSD menu (Input

Select function, see "Changing the monitor settings" chapter).

Ê Plug the power adapter cable into the power connector (2) of the monitor.

Ê Firmly insert the socket with the power cable supplied into the power cable connection of the

power adapter and check whether the socket is securely seated.

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 9

Ê Mount the cover over the connections again.

Connecting cables to the computer

Information on the computer connections and interfaces is contained in the operating manual for

your computer.

If your computer has two monitor ports ("onboard" screen controller and separate

graphics card), the monitor port for the separate graphics card is usually active.

Ê Connect the data cable to the (active) monitor port on the computer and secure the plug-in

connection by tightening the safety screws.

Ê Connect the male receptacle of the power cable supplied to the monitor socket of the computer

and ensure a secure connection.

Ê Plug the power connector of the computer into a properly grounded mains outlet.

When you start working with your monitor for the first time you should install the

appropriate graphics drivers for your application software. Details of how to do this are

provided in the documentation on your screen controller/the associated driver software.

Operation of the monitor

The monitor offers the following possibilities that enable it to be optimally adjusted for the respective

user and the respective situation.

Adjusting rake and rotation

The rake of the monitor can be adjusted by –5°

(forward) and +20° (back) from its vertical

position.

Ê Grasp the monitor with both hands on the

right and left edge of the casing and adjust

it to the desired rake.

The monitor can be rotated by ± 45° from its

centre position.

Ê Grasp the monitor with both hands on the

right and left edge of the casing and rotate it

into the desired position.

Colour monitor 463V FA

10 - English A26361-K864-Z100-1-5E19

Switching the monitor on/off

1 = Buttons for the OSD menu

(On-Screen-Display)

2 = Power indicator

3 = Power button

The ON/OFF switch (3) is used for switching the monitor on and off.

The power indicator (2) glows green when the monitor and computer are switched on. The power

indicator glows orange when the monitor does not receive a video signal or is in the energy-saving

mode. The power indicator goes off when the monitor is switched off.

When you switch the computer system on, you must proceed in the following order:

Ê First switch the LCD monitor on with the ON/OFF switch (3).

Ê Then switch on the computer.

If your computer has a power management function (energy-saving mode), you should

read the "Notes on power management" section in this chapter.

Notes on power management

If your computer is equipped with power management, the monitor can support this function fully.

Here the monitor does not distinguish between the individual energy-saving modes of the computer

(standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the

mode with the highest energy-saving effect.

Stage ON Energy-saving mode

Power indicator lights green glows orange

Function Monitor

operating

normally

Monitor

is dark

Power consumption normal

< 60 W

reduced to < 3 W

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 11

If your computer detects inactivity (no input) it sends an appropriate signal to the monitor to reduce

the power consumption (energy-saving mode). The power indicator of the monitor changes colour to

indicate the status change.

Once an input is made at the computer the screen contents are redrawn and full power is restored.

For detailed information on how energy-saving mode operates refer to the Operating Manual or

Technical Manual of the computer.

When the monitor is switched to the energy-saving mode by the power management

system a power consumption of up to 3 W is maintained to feed the circuit for redrawing

the screen contents.

To completely switch off the power consumption, switch off the computer or pull the plug

of the monitor power cable out of the monitor socket of the computer.

Changing the monitor settings

When putting the monitor into operation for the first time, the screen display should be optimally

adapted to the screen controller used and adjusted in accordance with your needs.

Basic monitor settings with the floppy disk supplied

If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000,

Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be

set with the floppy disk supplied.

Ê Insert the supplied floppy disk into the floppy disk drive.

Ê Open the Readme file on the floppy disk and follow the instructions in the file.

Your monitor should now already be properly adjusted. If none of the above operating systems is

used or minor corrections are to be made to the screen display, then change the monitor settings

with the OSD menu.

Monitor settings with the buttons of the control panel

AUTOMENU \

INPUT

1 = Buttons for the OSD menu

(On-Screen-Display)

2 = Power indicator

3 = Power button

Use the buttons of the control panel to make the following monitor settings directly while the OSD

menu is switched off.

Colour monitor 463V FA

12 - English A26361-K864-Z100-1-5E19

Performing auto-adjustment of the monitor

Ê Press the MENU \ AUTO button for approx. 1 second while the OSD menu is switched off.

The Auto Processing message is displayed.

Picture quality and position are set to optimum values for your system.

Adjusting contrast/background lighting

Ê Press the + or – button to call the Contrast / Backlight setting window.

This setting window can also be called, when the OSD menu is locked.

Selecting input signal

The monitor can be operated with analogue or digital signals. You can switch between the analogue

and the digital mode (depending on the graphics card you use).

Ê Press the INPUT button to change the mode of the input signal.

Locking the OSD menu

The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor

settings.

Ê Press the MENU \ AUTO button and the + button simultaneously and hold them until the status

indicator on the screen is completely filled.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked OSD menu again.

Locking the ON/OFF button

The ON/OFF switch can be locked to prevent the monitor from being switched off inadvertently or by

an unauthorised person.

Ê Press the MENU \ AUTO button and the + button simultaneously and hold them until the status

indicator on the screen is completely filled.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked ON/OFF switch again.

Monitor settings using the OSD menu

With the buttons on the control panel, call up and use the integrated OSD (On-Screen Display)

menu.

The OSD menu is available in different languages. The English menu names are used in

the following description (default setting). With the OSD function Language Select in the

Setup Menu you can select another language.

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 13

To set the OSD menu, perform the following steps:

Ê Briefly press the MENU \ AUTO button to activate the OSD menu.

The main menu appears on the screen with icons for the setting functions.

The first symbol (Auto Image Adjust) is

highlighted. At the bottom of the OSD menu

each button's function is displayed.

Ê Press the - or + button to highlight another

icon if necessary (e.g. Manual Image Adjust).

Ê Press the INPUT button to select the

highlighted icon.

The corresponding setting window (here: Manual Image Adjust) is displayed.

The first symbol (H. / V. Position) is highlighted.

Ê If necessary, press the - or + button to mark

the next icon.

Ê Press the INPUT button to select the

highlighted icon.

The icon's colour changes.

Ê Press the - or + button to adjust the

selected function.

Ê Press the MENU \ AUTO button to save the

settings.

The icon's colour changes.

Ê Press the - or + button to mark another

symbol or press the MENU \ AUTO button

to return to the main menu.

All changes are stored automatically.

If you want to change other settings, select the corresponding function from the OSD main menu. All

possible adjustments of the main menu are described in the following.

The OSD menu for analogue monitor operation is described in the following. During digital

operation some functions are not available, as they are not required due to the digital

transmission technology used.

Colour monitor 463V FA

14 - English A26361-K864-Z100-1-5E19

Performing auto-adjustment

Performing auto-adjustment (Auto Image Adjust)

The Auto Processing message is displayed.

Adjusting the brightness and contrast

Calling the Contrast / Brightness / Backlight setting window.

Setting the contrast of the display (Contrast)

This function allows you to modify the contrast of bright colour tones.

Setting the brightness of the display (Brightness)

This function allows you to modify the contrast of dark colour tones.

Setting the brightness of the background lighting (Backlight)

This function allows you to change the brightness of the entire display.

If the contrast is set too high, bright surfaces can no longer be distinguished from very

bright surfaces. If the contrast is set too low, the maximum brightness will not be

achieved.

Adjusting size and position

Calling the Manual Image Adjust setting window

Adjusting picture position (H./V.Position)

The INPUT button allows you to switch between the H.Position and the

V.Position.

Adjusting the horizontal size (H.Size)

There is an optimum setting for every resolution.

Eliminating picture interference (Fine Tune)

This function enables the fine tuning of your monitor in case of picture

interferences.

Adjusting the Zoom

This function allows you to enlarge a section of the display.

Colour monitor 463V FA

A26361-K864-Z100-1-5E19 English - 15

Setting colour temperature and colours

Calling the Color Adjust setting window

Selecting colour temperature (Color Temperature)

The "warmth" of the screen colours is set using the colour temperature.

The colour temperature is measured in K (= Kelvin). You can select from

9300 K, 6500 K, 5400 K, 5000 K and Native.

Native = original colour of the LCD display

Setting user-defined colours (User Color)

In the user-defined setting you can change the colour ratios of the basic

colours (red, green, blue) as required.

Adjusting the intensity of the grey levels (Gamma correction) (Gamma)

This function allows you to optimise the display of multimedia

applications.

Linear = default setting

Emphasize Brighter Level = Bright areas remain bright, dark areas become

darker

Emphasize Darker Level = Dark areas remain dark, bright areas become

brighter

Setting functions in the "Advanced Menu" menu

Calling the Advanced Menu setting window

Setting scaling (Scaling)

1:1 = full picture size (depending on the resolution)

Fill All = switch on the full-screen mode. The display area is stretched to

the full picture size (1,280 pixels, side ratio 5:4). As a result, the display

may appear distorted.

Fill Aspect Ratio = Switch on the proportional full-screen mode: The

display area is expanded to the maximum picture size while maintaining

the side ratio (either full picture width or full picture height).

Adjusting the picture quality in case of interpolation (Sharpness)

This function allows you to set the sharpness of the interpolation filter.

Thus the display can be optimised for pictures or texts.

Displaying the monitor information (Information)

This function allows you to display e.g. the current resolution and refresh

rate.

Page is loading ...

Fujitsu TFT 463VFA User manual

Brand: Fujitsu

Model: TFT 463VFA

Category: TVs & monitors

Type: User manual

This manual is also suitable for

463V FA

Download PDF

report

Fujitsu TFT 463VFA User manual

This manual is also suitable for

Fujitsu TFT 463VFA User manual

Related papers

Other documents