2. Kichler Lighting
  3. 43194MIZ
43194MIZ

Kichler Lighting 43194MIZ, 43194AP User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 43194MIZ User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
3) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
4) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
5) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
6) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
7) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
8) Insert recommended bulbs.
9) Screw short end of threaded pipe with hexnut into coupling
in center of socket cluster.
10) Slip hole in cupped washer over end of threaded pipe.
11) Raise shade up to fixture. Pass hole in bracket on shade
over end of threaded pipe.
12) Raise glass up to fixture. Fit glass inside shade and carefully
pass threaded pipe through hole in glass.
13) Pass bottom trim over threaded pipe.
14) Screw hexnut onto threaded pipe. (DO NOT over tighten.)
15) Screw finial onto end of threaded pipe. (DO NOT over tighten.)
Date Issued: 7/3/15 IS-43194-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
KNURL KNOB
PERILLA ESTRADA
GLASS
VIDRIO
THREADED PIPE
TUBO ROSCADO
HEXNUT
TUERCA HEXAGONAL
HEXNUT
TUERCA
HEXAGONAL
SHADE
PANTALLA
BOTTOM TRIM
GUARNICIÓN INFERIOR
FINIAL
CAPUCHON
SOCKET CLUSTER
GRUPO CASQUILLO
CUPPED WASHER
ARANDELA AHUECADA
Page is loading ...
1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
3) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
4) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
5) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
6) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
7) Insert recommended bulbs.
8) Screw short end of threaded pipe with hexnut into coupling
in center of socket cluster.
9) Slip hole in cupped washer over end of threaded pipe.
10) Raise shade up to fixture. Pass hole in bracket on shade
over end of threaded pipe.
11) Raise glass up to fixture. Fit glass inside shade and carefully
pass threaded pipe through hole in glass.
12) Pass bottom trim over threaded pipe.
13) Screw hexnut onto threaded pipe. (DO NOT over tighten.)
14) Screw finial onto end of threaded pipe. (DO NOT over tighten.)
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 7/3/15 IS-43194-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-
LATIONS.
VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-
DUCTIONS EN FRANÇAIS.
MOUNTING STRAP
PATTE DE FIXATION
CANOPY
CACHE
KNURL KNOB
BOUTON MOLETÉ
GLASS
VERRE
THREADED PIPE
TUBE FILETÉ
HEXNUT
ECROU HEXAGONAL
HEXNUT
ECROU
HEXAGONAL
FINIAL
ORNEMENT
SHADE
PANTALLA
BOTTOM TRIM
GARNITURE INFÉRIEURE
CUPPED WASHER
RONDELLE EN
FORME DE COUPE
SOCKET CLUSTER
GRAPPE DE DOUILLE
Page is loading ...
/