www.bigjohnproducts.com
MADE IN THE U.S.A.
Installation
Instructions
Height
Adjustment
From
7.5” to 14”
Part #
612011919-S
Support Stop
Included
Part #
612011919
Height
Adjustment
From
7.5” to 14”
Height
Adjustment
From
5” to 7.5”
See Our
Toilet Seats
on the back
Open front original
seat without cover shown.
Part#2445263-4W
PRODUCTS
www.bigjohnproducts.com
800 lbs. Capacity
1
½
” Rise
ABS Hinges
STANDARD
BIG JOHN TOILET SEAT
BIG JOHN TOILET SEAT
Other Genuine Big John Products
BIG JOHN
COMMODE
CHAIR
BIG JOHN
COMMODE
CHAIR
1,000 lb. capacity
Versatile use:
Bedside or
over toilets
1,000 lbs. Capacity
2 ½” Rise
Unbreakable Stainless Steel Hinges
14” wide from Side to Side
CLASSIC
19” wide from Side to Side
1200 lbs. Capacity
2 ½” Rise
Stainless Steel Hinges
ORIGINAL
The new era of stability, comfort and safety
Regular seats are too small and too flimsy.
Perfect for Hospitals, Nursing Homes,
Government Facilities, Stadiums, Airports,
Theaters and Office Buildings.
For more information
about our NEW
Plunger Splash Guard
and other genuine
Big John Products visit
our website.
The Big John toilet
seat in comparison
with a regular sized
seat. 75% Larger
Sitting Area
NEW
MADE IN THE U.S.A.
ADA Compliant Registration Number 4.23 ADAAG
Meets or exceeds
ASME / ANSI Z124.5
CSA
IAPMO / UPC
Big John Products 8533 Canoga Ave. Suite D, Canoga Park, CA 91304
TOLL FREE: 866-366-0669
PRODUCTS
www.bigjohnproducts.com
PLUNGER
SPLASH GUARD
PLUNGER
SPLASH GUARD
When plunging your clogged
toilet, PROTECTION is key!
The Plunger Splash Guard
keeps the water and germs
in the toilet bowl where
they belong.
NEW
6
6 Easy Step-by-Step Instructions for Installing the Big John Toilet Support
Step Step Step
Step Step
6
Step
www.bigjohnproducts.com
TOLL FREE: 866-366-0669
1
2
3
4
5
For toilets that have a
raised section at the
bottom of the toilet bowl,
remove the enclosed insert
to allow for a tight fit.
For toilets that don’t have
a raised section at the
bottom of the toilet bowl,
put the insert into the
grooves on the carriage.
Remove liner from adhesive
tape on the top of the
carriage and place the Toilet
Support in position under
the toilet bowl.
Use one of the enclosed
alcohol wipes to clean under
the toilet where the support
meets the toilet bowl.
DO NOT CAULK THE TOP OF
THE CARRIAGE. MAKE SURE
BOTTOM OF TOILET IS
CLEAN BEFORE INSTALLING.
With the Toilet Support
under the bowl unscrew
the leg down to the floor.
DO NOT OVERTIGHTEN.
Make sure the Toilet
Support is mounted
straight and that it is
centered under the toilet.
OPTIONAL SUPPORT STOP
INSTALLATION
Mark spot where the leg meets
the floor. Raise leg and adhere
support stop to floor using an
adhesive best suitable for
adhering aluminum.
Unscrew the leg to tighten it
snugly against the floor.
DO NOT OVERTIGHTEN.
Wipe around the entire
carriage and toilet where
they meet, with the enclosed
alcohol wipes, to remove
any dirt.
Apply a bead of the enclosed caulk around
the entire Toilet Support carriage where it
meets the toilet. Make sure to fill in all gaps.
Wipe off any excess with a damp cloth.
Allow it to cure for 24 hours.
Once caulk has cured, leg can be raised
to clean underneath it. Re-lower
the leg after cleaning, making
sure that it fits snugly.
1
2 3
4 5
For the Short Swivel
Place under P-trap or any
other suitable forward position.
Short
Swivel
Support
For toilets that the
large support doesn’t fit.
PRODUCTS
www.bigjohnproducts.com
/
